Skip to content
info@engineeringhardware.com
WhatsApp
Request a Quote
Tools · DIN 3126 / ISO 1173 (C6.3 hexagon drive) · Application guide

What Are Cross-Recess Screwdriver Bits (PH / PZ) Used For?

Typical applications, the industries that specify cross-recess screwdriver bits (ph / pz), and how to choose the right size, material and finish for the joint.

Cross-Recess Screwdriver Bits (PH / PZ) are used for installing, adjusting or servicing the assembly rather than forming part of it. They are manufactured to DIN 3126 / ISO 1173 (C6.3 hexagon drive), and selection is driven by the size designation, the fit and tolerance the assembly requires, and the service environment.

Primary duty
Installing, adjusting or servicing the assembly rather than forming part of it
Governing standard
DIN 3126 / ISO 1173 (C6.3 hexagon drive)
Size designation range
PZ1 to PZ3
Category
Tools

Application notes are general engineering guidance. Verify the property class and any approval requirement against your own design calculation.

What Are Cross-Recess Screwdriver Bits (PH / PZ) Used For? application image

Cross-Recess Screwdriver Bits (PH / PZ) (DIN 3126 / ISO 1173 (C6.3 hexagon drive)) are specified where the joint requires installing, adjusting or servicing the assembly rather than forming part of it. The sections below cover the typical end-uses by industry, the size and material decisions for each, assembly practice, and the applications this fastener type is not suited to. Stocked across roughly 1 to 3, they cover light-duty and instrument-scale work.

Typical Applications for Cross-Recess Screwdriver Bits (PH / PZ)

The most common settings where these are specified:

  • General machine building: fastening covers, brackets, motors and sub-assemblies on production equipment.
  • Maintenance & repair (MRO): a stocked size for servicing existing plant where the original fastener spec must be matched.
  • Fabrication & metalwork: bench and on-site assembly of steel frames, enclosures and weldments.

How to Specify Cross-Recess Screwdriver Bits (PH / PZ) for Your Application

  • Size: Select on size designation, and confirm it against the mating feature in the assembly. This product spans 1–3; check the full table below for the exact dimensions of each size.
  • Material: Choose the material and finish for the service environment — plated steel for general use, stainless for corrosion resistance.
  • Environment: For damp, coastal or chemical exposure prefer A4/316 stainless or a suitable coating; indoors, plated steel or A2 is usually sufficient.
  • Standard: This product is supplied to DIN 3126 / ISO 1173 (C6.3 hexagon drive). Quoting the standard on your order guarantees interchangeable dimensions between suppliers.

Where Cross-Recess Screwdriver Bits (PH / PZ) Are Not the Right Choice

Match the fastener to the load, environment and whether the joint must be reopened; the wrong class or style is the usual cause of joint failure.

Technical Drawing

Customize the parameters below — every spec field is editable, and the drawing redraws to match the values you choose. Changing the size will snap the other fields to that size's standard values; you can then override any individual value.

Sends the selected values to the quote form below.

Request a Quote

The form below follows the current technical drawing configuration. Change the drawing values above and the request details update automatically.

Request a Quotation

Specification
Business Information

Dimensions & Specifications (DIN 3126 / ISO 1173 (C6.3 hexagon drive))

BitRecessTypical screw sizeDistinguishing mark on the screw
PH0PhillipsM2 u2013 M2.5plain cross, tapered flanks
PH1PhillipsM3 u2013 M3.5plain cross, tapered flanks
PH2PhillipsM4 u2013 M5plain cross, tapered flanks
PH3PhillipsM6 u2013 M8plain cross, tapered flanks
PZ1PozidrivM3 u2013 M3.5cross plus four fine radial ticks
PZ2PozidrivM4 u2013 M5cross plus four fine radial ticks
PZ3PozidrivM6 u2013 M8cross plus four fine radial ticks
Inside the plant

Manufactured in our own plant

This part is cold-formed, threaded, heat-treated and finished in-house. The stages below are where its class and finish are actually decided.

  1. Wire rod feeding into a cold heading machine
    01

    Cold heading

    Wire rod is drawn to size and cold-formed into blanks. Forming rather than cutting keeps the grain flow continuous around the head, which is where a bolt is most likely to fail.

    Head dimensions and under-head radius checked at set-up and per shift.

  2. Thread rolling machine producing bolt threads
    02

    Thread rolling

    Threads are rolled between hardened dies rather than cut. Rolled threads are stronger in fatigue than cut threads and hold pitch and flank angle far more consistently across a batch.

    Go / no-go ring gauges to ISO 965 tolerance class 6g.

  3. Baskets of bolts staged for heat treatment
    03

    Heat treatment

    Quench-and-temper brings carbon and alloy steel to the property class ordered — 8.8, 10.9 or 12.9 — with the furnace charge tracked so a finished lot can be traced back to it.

    Core hardness and tensile tested per lot to ISO 898-1.

  4. Zinc plated bolts in a treatment basket
    04

    Surface treatment

    Zinc, zinc-nickel, hot-dip galvanizing, black oxide, phosphate and Dacromet, selected against the service environment rather than against the price list.

    Coating thickness and neutral salt spray hours to ISO 9227.

Frequently Asked Questions

What are Cross-Recess Screwdriver Bits (PH / PZ) used for?

Installing, adjusting or servicing the assembly rather than forming part of it. They are supplied to DIN 3126 / ISO 1173 (C6.3 hexagon drive).

Which industries use Cross-Recess Screwdriver Bits (PH / PZ)?

They are commonly specified in general machine building, maintenance & repair (mro) and fabrication & metalwork, among other sectors.

How do I choose the right size of Cross-Recess Screwdriver Bits (PH / PZ)?

Select on size designation and on the fit the assembly requires. This product is available from 1 to 3; the full dimension table on this page lists each size.

Are Cross-Recess Screwdriver Bits (PH / PZ) made to a recognized standard?

Yes — they are manufactured to DIN 3126 / ISO 1173 (C6.3 hexagon drive), so dimensions are interchangeable between suppliers when you quote the standard on your order.

Can I get a quote for Cross-Recess Screwdriver Bits (PH / PZ) in the size and material I need?

Yes. Use the technical drawing and quote form on this page to set the size and options, then send the exact configuration to our team for pricing and lead time.