---
title: "What Are Friction-Bearing Ball Spring Plungers Used For?"
description: "Friction-Bearing Ball Spring Plungers (Trade series (GN 615.8)) are used for friction-bearing ball contact with a defined spring load. Catalogued M5 to M16."
url: https://engineeringhardware.com/applications/friction-bearing-ball-spring-plungers-gn-615-8/
source: Engineering Hardware & Fasteners
---

# What Are Friction-Bearing Ball Spring Plungers Used For?

Pins · Trade series (GN 615.8) · Application guide

Typical applications, the industries that specify friction-bearing ball spring plungers, and how to choose the right size, material and finish for the joint.

Friction-Bearing Ball Spring Plungers are used for friction-bearing ball contact with a defined spring load. They are manufactured to Trade series (GN 615.8), and selection is driven by the thread size, the fit and tolerance the assembly requires, and the service environment.

- **Primary duty:** Friction-bearing ball contact with a defined spring load
- **Governing standard:** Trade series (GN 615.8)
- **Thread size range:** M5 to M16
- **Category:** Pins

Application notes are general engineering guidance. Verify the property class and any approval requirement against your own design calculation.

![What Are Friction-Bearing Ball Spring Plungers Used For? application image](https://engineeringhardware.com/wp-content/uploads/2026/09/Friction-Bearing-Ball-Spring-Plungers.webp)

Friction-Bearing Ball Spring Plungers are used primarily for friction-bearing ball contact with a defined spring load. This page lists the industries and assemblies where they are specified, the selection criteria that matter for each application, installation practice, and the cases where a different fastener type is the correct choice. Parts are supplied to Trade series (GN 615.8). Stocked across roughly M5 to M16, they cover general to heavy-duty work.

## Typical Applications for Friction-Bearing Ball Spring Plungers

The most common settings where these are specified:

- **Positioning mechanisms:** friction-bearing ball plungers for repeat contact on moving surfaces.
- **Fixture plates:** detent points where low sliding friction matters.
- **Drawer and slide hardware:** ball contact that holds a mechanism in position.
- **Assembly tooling:** replaceable contact elements on changeover fixtures.

Product catalog

## Related Spring Plungers products

[![OEM Suppliers of Polished Coiled Spring Pins for Industry](https://img.engineeringhardware.com/OEM-Suppliers-of-Polished-Coiled-Spring-Pins-for-Industry.webp)](https://engineeringhardware.com/product/oem-suppliers-of-polished-coiled-spring-pins-for-industry/)

Spring, Roll & Coiled Pins

### [OEM Suppliers of Polished Coiled Spring Pins for Industry](https://engineeringhardware.com/product/oem-suppliers-of-polished-coiled-spring-pins-for-industry/)

Stainless Steel · Ordinary/Polished/Galvanized/Oxidized/Nickel Plate

**US$0.024 – 0.06**MOQ 1,000 pieces

[![Black Oxide Grooved Spring Pin – Carbon Steel, Standard & Heavy Duty](https://img.engineeringhardware.com/Black-Oxide-Grooved-Spring-Pin-Carbon-Steel-Standard-Heavy-Duty.webp)](https://engineeringhardware.com/product/black-oxide-grooved-spring-pin-carbon-steel-standard-heavy-duty/)

Spring, Roll & Coiled Pins

### [Black Oxide Grooved Spring Pin – Carbon Steel, Standard & Heavy Duty](https://engineeringhardware.com/product/black-oxide-grooved-spring-pin-carbon-steel-standard-heavy-duty/)

Round Head · DIN, GB, ANSI

**US$0.0012**MOQ 10,000 pieces

[![Steel Us System Hair Type Split Spring Pin](https://img.engineeringhardware.com/Steel-Us-System-Hair-Type-Split-Spring-Pin.webp)](https://engineeringhardware.com/product/steel-us-system-hair-type-split-spring-pin/)

Spring, Roll & Coiled Pins

### [Steel Us System Hair Type Split Spring Pin](https://engineeringhardware.com/product/steel-us-system-hair-type-split-spring-pin/)

Split Spring Pin · DIN94

**US$0.072 – 0.37**MOQ 500 pieces

[![High Elastic Clevis Roll Pin Anti-Loose Fastener for Automotive Parts](https://img.engineeringhardware.com/High-Elastic-Clevis-Roll-Pin-Anti-Loose-Fastener-for-Automotive-Parts.webp)](https://engineeringhardware.com/product/high-elastic-clevis-roll-pin-anti-loose-fastener-for-automotive-parts/)

Spring, Roll & Coiled Pins

### [High Elastic Clevis Roll Pin Anti-Loose Fastener for Automotive Parts](https://engineeringhardware.com/product/high-elastic-clevis-roll-pin-anti-loose-fastener-for-automotive-parts/)

Stainless Steel, Carbon Steel, Brass · Machinery/Building/Chemical Ind…

**US$0.012 – 0.36**MOQ 1,000 pieces

[![Kp-534, MB-294272, Mk526240, MK385991, Mc992486 Mitsubishi Canter Fuso 35 (3s13) / 75 (7C15) King Pin Kits](https://img.engineeringhardware.com/Kp-534-MB-294272-Mk526240-MK385991-Mc992486-Mitsubishi-Canter-Fuso-35-3s13-75-7C15-King-Pin-Kits.webp)](https://engineeringhardware.com/product/kp-534-mb-294272-mk526240-mk385991-mc992486-mitsubishi-canter-fuso-35-3s13-75-7c15/)

Spring, Roll & Coiled Pins

### [Kp-534, MB-294272, Mk526240, MK385991, Mc992486 Mitsubishi Canter Fuso 35 (3s13) / 75 (7C15) King Pin Kits](https://engineeringhardware.com/product/kp-534-mb-294272-mk526240-mk385991-mc992486-mitsubishi-canter-fuso-35-3s13-75-7c15/)

Spring Pin · Steel

**US$4.80 – 8.40**MOQ 200 pieces

[![M3 M4 M5 Stainless Steel 304 316 Full Length Spring Pin Grooved Pin](https://img.engineeringhardware.com/M3-M4-M5-Stainless-Steel-304-316-Full-Length-Spring-Pin-Grooved-Pin.webp)](https://engineeringhardware.com/product/m3-m4-m5-stainless-steel-304-316-full-length-spring-pin-grooved-pin/)

Spring, Roll & Coiled Pins

### [M3 M4 M5 Stainless Steel 304 316 Full Length Spring Pin Grooved Pin](https://engineeringhardware.com/product/m3-m4-m5-stainless-steel-304-316-full-length-spring-pin-grooved-pin/)

Clevis Pin · DIN1474

**US$0.22 – 0.29**MOQ 1,000 pieces

[View all Spring, Roll & Coiled Pins →](https://engineeringhardware.com/fastener-products/pins-dowel-fasteners/spring-roll-coiled-pins/) [Full product catalog](https://engineeringhardware.com/products/)

## How to Specify Friction-Bearing Ball Spring Plungers for Your Application

- **Size:** Match the nominal size to the mating thread or hole. This product spans M5–M16; check the full table below for the exact dimensions of each size.
- **Material:** Choose the material and finish for the service environment — plated steel for general use, stainless for corrosion resistance.
- **Environment:** For damp, coastal or chemical exposure prefer A4/316 stainless or a suitable coating; indoors, plated steel or A2 is usually sufficient.
- **Standard:** This product is supplied to Trade series (GN 615.8). Quoting the standard on your order guarantees interchangeable dimensions between suppliers.

## Installation & Assembly Practice

- Ream the hole to the specified fit class; a dowel pressed into a drilled-only hole will not locate accurately.
- Press pins in with steady force rather than hammer blows where possible, and chamfer the hole entry.

## Common Selection Mistakes with Friction-Bearing Ball Spring Plungers

- Using a dowel pin as a load-carrying shear bolt — dowels locate, they are not sized for sustained shear.
- Ignoring the fit class: a locational fit and an interference fit need different hole tolerances.

## Where Friction-Bearing Ball Spring Plungers Are Not the Right Choice

Not for carrying significant tensile or repeated heavy shear loads — use a bolt or a keyed joint for that.

Custom manufacturing · Made to drawing

## Need a friction-bearing ball spring plungers outside the standard range?

Tolerance class is what a special pin usually turns on — a locating pin and a retaining pin want very different fits in the same nominal size. Made by cold heading or turning.

Minimum order from 2,000 pieces; samples within 7 days of drawing approval.

[Custom pin manufacturing](https://engineeringhardware.com/custom/pins/)[Send a drawing](https://engineeringhardware.com/custom/pins/#rfq)

## Technical Drawing

Dimensioned line drawing of M5 Friction-Bearing Ball Spring Plungers to Trade series (GN 615.8). Side view and top view, drawn to the dimensions in the table below and redrawn for any size selected.

- **Length L (mm):** 12
- **Ball diameter (mm):** 2
- **Standard spring initial/end load (N):** 4.8 / 6.8
- **High-load spring initial/end load (N):** 10 / 14
- **Housing material:** blackened steel or AISI 303 stainless

## Dimensions & Specifications (Trade series (GN 615.8))

| Thread size | Length L (mm) | Ball diameter (mm) | Standard spring initial/end load (N) | High-load spring initial/end load (N) | Housing material |
| --- | --- | --- | --- | --- | --- |
| M5 | 12 | 2 | 4.8 / 6.8 | 10 / 14 | blackened steel or AISI 303 stainless |
| M6 | 14 | 2.5 | 6.3 / 10 | 11 / 16 | blackened steel or AISI 303 stainless |
| M8 | 16 | 3.5 | 16 / 24 | 23 / 40 | blackened steel or AISI 303 stainless |
| M10 | 19 | 4.5 | 18.8 / 31.7 | 28 / 54.3 | blackened steel or AISI 303 stainless |
| M12 | 22 | 6.5 | 26 / 49 | 39.5 / 77.3 | blackened steel or AISI 303 stainless |
| M16 | 24 | 8.5 | 38 / 68 | 50 / 88.7 | blackened steel or AISI 303 stainless |

Inside the plant

## Manufactured in our own plant

This part is cold-formed, threaded, heat-treated and finished in-house. The stages below are where its class and finish are actually decided.

1. ![Wire rod feeding into a cold heading machine](https://engineeringhardware.com/wp-content/uploads/2026/08/09-wire-rod-feed-cold-heading-machine.webp) 01 **Cold heading** Wire rod is drawn to size and cold-formed into blanks. Forming rather than cutting keeps the grain flow continuous around the head, which is where a bolt is most likely to fail. Head dimensions and under-head radius checked at set-up and per shift.
2. ![Thread rolling machine producing bolt threads](https://engineeringhardware.com/wp-content/uploads/2026/08/03-thread-rolling-machine-bolt-production.webp) 02 **Thread rolling** Threads are rolled between hardened dies rather than cut. Rolled threads are stronger in fatigue than cut threads and hold pitch and flank angle far more consistently across a batch. Go / no-go ring gauges to ISO 965 tolerance class 6g.
3. ![Baskets of bolts staged for heat treatment](https://engineeringhardware.com/wp-content/uploads/2026/08/05-heat-treatment-baskets-black-bolts.webp) 03 **Heat treatment** Quench-and-temper brings carbon and alloy steel to the property class ordered — 8.8, 10.9 or 12.9 — with the furnace charge tracked so a finished lot can be traced back to it. Core hardness and tensile tested per lot to ISO 898-1.
4. ![Zinc plated bolts in a treatment basket](https://engineeringhardware.com/wp-content/uploads/2026/08/23-zinc-plated-bolts-treatment-basket.webp) 04 **Surface treatment** Zinc, zinc-nickel, hot-dip galvanizing, black oxide, phosphate and Dacromet, selected against the service environment rather than against the price list. Coating thickness and neutral salt spray hours to ISO 9227.

## Frequently Asked Questions

### What are Friction-Bearing Ball Spring Plungers used for?

Friction-bearing ball contact with a defined spring load. They are supplied to Trade series (GN 615.8).

### Which industries use Friction-Bearing Ball Spring Plungers?

They are commonly specified in assembly tooling, positioning mechanisms and fixture plates, among other sectors.

### How do I choose the right size of Friction-Bearing Ball Spring Plungers?

Match the nominal size to the mating thread or hole. This product is available from M5 to M16; the full dimension table on this page lists each size.

### What material should Friction-Bearing Ball Spring Plungers be for outdoor use?

For damp, coastal or chemical environments specify A4 (316) stainless or a suitably coated steel. For indoor or dry use, A2 (304) stainless or zinc-plated steel is normally adequate.

### Can I get a quote for Friction-Bearing Ball Spring Plungers in the size and material I need?

Yes. Use the technical drawing and quote form on this page to set the size and options, then send the exact configuration to our team for pricing and lead time.

## Related Pages

Product page: [Friction-Bearing Ball Spring Plungers — specifications & sizes](https://engineeringhardware.com/fastener/friction-bearing-ball-spring-plungers-gn-615-8/)

### Friction-Bearing Ball Spring Plungers Specification Guides

### Related Fastener Applications
