---
title: "What Are Micro Thin-Head Phillips Machine Screws Used For?"
description: "Micro Thin-Head Phillips Machine Screws (Trade series (micro machine screws)) are used for threaded assemblies where the head drive and seating style matter."
url: https://engineeringhardware.com/applications/micro-thin-head-phillips-machine-screws/
source: Engineering Hardware & Fasteners
---

# What Are Micro Thin-Head Phillips Machine Screws Used For?

Screws · Trade series (micro machine screws) · Application guide

Typical applications, the industries that specify micro thin-head phillips machine screws, and how to choose the right size, material and finish for the joint.

Micro Thin-Head Phillips Machine Screws are used for threaded assemblies where the head drive and seating style matter. They are manufactured to Trade series (micro machine screws), and the choice of size, property class and finish is driven by the load in the joint and the environment it sits in.

- **Primary duty:** Threaded assemblies where the head drive and seating style matter
- **Governing standard:** Trade series (micro machine screws)
- **Thread size range:** M1.4 to M2.0
- **Category:** Screws

Application notes are general engineering guidance. Verify the property class and any approval requirement against your own design calculation.

![What Are Micro Thin-Head Phillips Machine Screws Used For? application image](https://engineeringhardware.com/wp-content/uploads/2026/09/Micro-Thin-Head-Phillips-Machine-Screws.webp)

Micro Thin-Head Phillips Machine Screws are selected when an assembly calls for threaded assemblies where the head drive and seating style matter. This application guide to the Trade series (micro machine screws) type covers concrete end-uses, the specification checklist, correct installation, and where an alternative fastener performs better. Stocked across roughly M1.4 to M2, they cover light-duty and instrument-scale work.

## Typical Applications for Micro Thin-Head Phillips Machine Screws

The most common settings where these are specified:

- **Thin electronics:** The 0.2 mm head thickness leaves clearance above miniature shields.
- **Sensors and optics:** Low-profile Phillips hardware fits around lenses and adjustment mechanisms.
- **Compact mechanisms:** Small heads secure covers where counterboring is not available.
- **Precision service:** Short micro screws replace damaged hardware without adding head height.

Product catalog

## Related Micro & Miniature Screws products

[![Vodafast Round Flat Head Screw with Plastic Head Assembled](https://img.engineeringhardware.com/Vodafast-Round-Flat-Head-Screw-with-Plastic-Head-Assembled.webp)](https://engineeringhardware.com/product/vodafast-round-flat-head-screw-with-plastic-head-assembled/)

Countersunk & Flat-Head Machine Screws

### [Vodafast Round Flat Head Screw with Plastic Head Assembled](https://engineeringhardware.com/product/vodafast-round-flat-head-screw-with-plastic-head-assembled/)

Round Head · DIN, GB, ANSI, BSW, JIS, GOST

**US$0.0084 – 0.012**MOQ 10,000 pieces

[![Wood Building Screw Countersunk Head Torx Drive with Nibs&Type 17 Cutting Point](https://img.engineeringhardware.com/Wood-Building-Screw-Countersunk-Head-Torx-Drive-with-Nibs-Type-17-Cutting-Point.webp)](https://engineeringhardware.com/product/wood-building-screw-countersunk-head-torx-drive-with-nibs-type-17-cutting-point/)

Countersunk & Flat-Head Machine Screws

### [Wood Building Screw Countersunk Head Torx Drive with Nibs&Type 17 Cutting Point](https://engineeringhardware.com/product/wood-building-screw-countersunk-head-torx-drive-with-nibs-type-17-cutting-point/)

Countersunk Head · DIN, GB, ANSI, BSW, JIS, GOST

**US$1.69 – 2.53**MOQ 900 kilograms

[![Collated Screws with Countersunk Head Type17](https://img.engineeringhardware.com/Collated-Screws-with-Countersunk-Head-Type17.webp)](https://engineeringhardware.com/product/collated-screws-with-countersunk-head-type17/)

Countersunk & Flat-Head Machine Screws

### [Collated Screws with Countersunk Head Type17](https://engineeringhardware.com/product/collated-screws-with-countersunk-head-type17/)

Swrch22A · nom

**US$0.012 – 0.30**MOQ 50,000 pieces

[![Powerful Magnet Disc with Countersunk Hole Neodymium Magnet with Screw Hole](https://img.engineeringhardware.com/Powerful-Magnet-Disc-with-Countersunk-Hole-Neodymium-Magnet-with-Screw-Hole.webp)](https://engineeringhardware.com/product/powerful-magnet-disc-with-countersunk-hole-neodymium-magnet-with-screw-hole/)

Countersunk & Flat-Head Machine Screws

### [Powerful Magnet Disc with Countersunk Hole Neodymium Magnet with Screw Hole](https://engineeringhardware.com/product/powerful-magnet-disc-with-countersunk-hole-neodymium-magnet-with-screw-hole/)

Neodymium-Iron-Boron · N52

**US$0.12 – 24.00**MOQ 10 pieces

[![GB/T 2673.1 Hexalobular Socket Countersunk Head Screw Torx Carbon Steel Zinc](https://img.engineeringhardware.com/GB-T-2673-1-Hexalobular-Socket-Countersunk-Head-Screw-Torx-Carbon-Steel-Zinc.webp)](https://engineeringhardware.com/product/gb-t-2673-1-hexalobular-socket-countersunk-head-screw-torx-carbon-steel-zinc/)

Countersunk & Flat-Head Machine Screws

### [GB/T 2673.1 Hexalobular Socket Countersunk Head Screw Torx Carbon Steel Zinc](https://engineeringhardware.com/product/gb-t-2673-1-hexalobular-socket-countersunk-head-screw-torx-carbon-steel-zinc/)

Torx Screw · GB

**US$0.012 – 0.024**MOQ 1,000 pieces

[![Heavy Duty Countersunk Ball Lock Pin for 3D Flexible Welding Platform](https://img.engineeringhardware.com/Heavy-Duty-Countersunk-Ball-Lock-Pin-for-3D-Flexible-Welding-Platform.webp)](https://engineeringhardware.com/product/heavy-duty-countersunk-ball-lock-pin-for-3d-flexible-welding-platform/)

Countersunk & Flat-Head Machine Screws

### [Heavy Duty Countersunk Ball Lock Pin for 3D Flexible Welding Platform](https://engineeringhardware.com/product/heavy-duty-countersunk-ball-lock-pin-for-3d-flexible-welding-platform/)

Welding Fixture Accessories · Alloy Steel Materials

**US$9.60 – 18.00**MOQ 1 piece

[View all Countersunk & Flat-Head Machine Screws →](https://engineeringhardware.com/fastener-products/screws/countersunk-flat-head-machine-screws/) [Full product catalog](https://engineeringhardware.com/products/)

## How to Specify Micro Thin-Head Phillips Machine Screws for Your Application

- **Size:** Match the nominal size to the mating thread or hole. This product spans M1.4–M2; check the full table below for the exact dimensions of each size.
- **Drive & head:** Pick the drive (socket, cross, slot) and head style for the tool access and seating surface; a recessed drive resists cam-out under power tools.
- **Environment:** For damp, coastal or chemical exposure prefer A4/316 stainless or a suitable coating; indoors, plated steel or A2 is usually sufficient.
- **Standard:** This product is supplied to Trade series (micro machine screws). Quoting the standard on your order guarantees interchangeable dimensions between suppliers.

## Installation & Assembly Practice

- Match the driver exactly to the recess (PH ≠ PZ; hex key sizes per ISO 2936) and keep the tool axial — side load is the main cause of stripped drives.
- In tapped holes, engage a thread length of at least 1× the nominal diameter in steel, 2× in aluminum.
- Set power tools to a torque that seats the head without embedding it into the mating surface.

## Common Selection Mistakes with Micro Thin-Head Phillips Machine Screws

- Under-sizing the drive for the installation torque — a small recess at high torque strips before the screw is seated.
- Using a countersunk head in thin sheet where the countersink removes most of the load-bearing material.
- Specifying stainless in high-strength duty: A2-70 is roughly class 7 steel, not a 10.9 substitute.

## Where Micro Thin-Head Phillips Machine Screws Are Not the Right Choice

Not for high-preload structural joints (use a property-class bolt and nut), and not in thin sheet where a self-drilling or self-tapping type suits better.

Custom manufacturing · Made to drawing

## Need a micro thin-head phillips machine screws outside the standard range?

Head form and drive can be specified to the assembly rather than to a standard: a larger bearing face, a security drive, or a socket sized for the tool already on the bench. Made by cold heading or warm forging.

Minimum order from 2,000 pieces; samples within 7 days of drawing approval.

[Custom screw manufacturing](https://engineeringhardware.com/custom/screws/)[Send a drawing](https://engineeringhardware.com/custom/screws/#rfq)

## Technical Drawing

Dimensioned line drawing of M1.4 Micro Thin-Head Phillips Machine Screws to Trade series (micro machine screws). Side view and top view, drawn to the dimensions in the table below and redrawn for any size selected.

- **Head diameter (mm):** 2.5
- **Head thickness (mm):** 0.2
- **Typical length range (mm):** 2~10
- **Drive:** miniature Phillips
- **Material options:** steel / stainless steel / brass

## Dimensions & Specifications (Trade series (micro machine screws))

| Thread size | Head diameter (mm) | Head thickness (mm) | Typical length range (mm) | Drive | Material options |
| --- | --- | --- | --- | --- | --- |
| M1.4 | 2.5 | 0.2 | 2~10 | miniature Phillips | steel / stainless steel / brass |
| M1.6 | 2.8 | 0.2 | 2~10 | miniature Phillips | steel / stainless steel / brass |
| M1.7 | 3.0 | 0.2 | 2~10 | miniature Phillips | steel / stainless steel / brass |
| M2.0 | 3.5 | 0.2 | 2~10 | miniature Phillips | steel / stainless steel / brass |

Inside the plant

## Manufactured in our own plant

This part is cold-formed, threaded, heat-treated and finished in-house. The stages below are where its class and finish are actually decided.

1. ![Wire rod feeding into a cold heading machine](https://engineeringhardware.com/wp-content/uploads/2026/08/09-wire-rod-feed-cold-heading-machine.webp) 01 **Cold heading** Wire rod is drawn to size and cold-formed into blanks. Forming rather than cutting keeps the grain flow continuous around the head, which is where a bolt is most likely to fail. Head dimensions and under-head radius checked at set-up and per shift.
2. ![Thread rolling machine producing bolt threads](https://engineeringhardware.com/wp-content/uploads/2026/08/03-thread-rolling-machine-bolt-production.webp) 02 **Thread rolling** Threads are rolled between hardened dies rather than cut. Rolled threads are stronger in fatigue than cut threads and hold pitch and flank angle far more consistently across a batch. Go / no-go ring gauges to ISO 965 tolerance class 6g.
3. ![Baskets of bolts staged for heat treatment](https://engineeringhardware.com/wp-content/uploads/2026/08/05-heat-treatment-baskets-black-bolts.webp) 03 **Heat treatment** Quench-and-temper brings carbon and alloy steel to the property class ordered — 8.8, 10.9 or 12.9 — with the furnace charge tracked so a finished lot can be traced back to it. Core hardness and tensile tested per lot to ISO 898-1.
4. ![Zinc plated bolts in a treatment basket](https://engineeringhardware.com/wp-content/uploads/2026/08/23-zinc-plated-bolts-treatment-basket.webp) 04 **Surface treatment** Zinc, zinc-nickel, hot-dip galvanizing, black oxide, phosphate and Dacromet, selected against the service environment rather than against the price list. Coating thickness and neutral salt spray hours to ISO 9227.

## Frequently Asked Questions

### What material should Micro Thin-Head Phillips Machine Screws be for outdoor use?

For damp, coastal or chemical environments specify A4 (316) stainless or a suitably coated steel. For indoor or dry use, A2 (304) stainless or zinc-plated steel is normally adequate.

### Are Micro Thin-Head Phillips Machine Screws made to a recognized standard?

Yes — they are manufactured to Trade series (micro machine screws), so dimensions are interchangeable between suppliers when you quote the standard on your order.

### What are Micro Thin-Head Phillips Machine Screws used for?

Threaded assemblies where the head drive and seating style matter. They are supplied to Trade series (micro machine screws).

### Which industries use Micro Thin-Head Phillips Machine Screws?

They are commonly specified in compact mechanisms, precision service and thin electronics, among other sectors.

### Can I get a quote for Micro Thin-Head Phillips Machine Screws in the size and material I need?

Yes. Use the technical drawing and quote form on this page to set the size and options, then send the exact configuration to our team for pricing and lead time.

## Related Pages

Product page: [Micro Thin-Head Phillips Machine Screws — specifications & sizes](https://engineeringhardware.com/fastener/micro-thin-head-phillips-machine-screws/)

### Micro Thin-Head Phillips Machine Screws Specification Guides

### Related Fastener Applications