---
title: "What Are Oval-Head Sheet-Metal Screws Used For?"
description: "Oval-Head Sheet-Metal Screws (Trade series (oval sheet-metal screws)) are used for forming a thread in sheet metal while retaining an oval head that sits int…"
url: https://engineeringhardware.com/applications/oval-head-sheet-metal-screws/
source: Engineering Hardware & Fasteners
---

# What Are Oval-Head Sheet-Metal Screws Used For?

Screws · Trade series (oval sheet-metal screws) · Application guide

Typical applications, the industries that specify oval-head sheet-metal screws, and how to choose the right size, material and finish for the joint.

Oval-Head Sheet-Metal Screws are used for forming a thread in sheet metal while retaining an oval head that sits into a shallow countersink. They are manufactured to Trade series (oval sheet-metal screws), and selection is driven by the screw size, the fit and tolerance the assembly requires, and the service environment.

- **Primary duty:** Forming a thread in sheet metal while retaining an oval head that sits into a shallow countersink
- **Governing standard:** Trade series (oval sheet-metal screws)
- **Screw size range:** #4 to #6
- **Category:** Screws

Application notes are general engineering guidance. Verify the property class and any approval requirement against your own design calculation.

![What Are Oval-Head Sheet-Metal Screws Used For? application image](https://engineeringhardware.com/wp-content/uploads/2026/09/Oval-Head-Sheet-Metal-Screws.webp)

The primary duty of Oval-Head Sheet-Metal Screws is forming a thread in sheet metal while retaining an oval head that sits into a shallow countersink. Below: the sectors that specify them in volume, the checklist used to select the right size and material for the application, installation notes, and the known limits of the type. Stocked across roughly 4 to 6, they cover light-duty and instrument-scale work.

## Typical Applications for Oval-Head Sheet-Metal Screws

The most common settings where these are specified:

- **Sheet-metal panels:** Oval pointed screws fasten thin sheet with a finished raised head.
- **Appliance trim:** 18-8 stainless resists corrosion on visible light-gauge panels.
- **Enclosures:** No. 1 and No. 2 drives fit the supplied small sizes.
- **Light fabrication:** The 82-degree seat is chosen where a flat appearance matters.

Product catalog

## Related Oval-Head Sheet-Metal Screws products

[![Factory Wholesale Long Yellow Zinc Countersunk Wafer Torx Building Timber Wood Construction Screws](https://img.engineeringhardware.com/Factory-Wholesale-Long-Yellow-Zinc-Countersunk-Wafer-Torx-Building-Timber-Wood-Construction-Screws.webp)](https://engineeringhardware.com/product/factory-wholesale-long-yellow-zinc-countersunk-wafer-torx-building-timber-wood/)

Countersunk & Flat-Head Machine Screws

### [Factory Wholesale Long Yellow Zinc Countersunk Wafer Torx Building Timber Wood Construction Screws](https://engineeringhardware.com/product/factory-wholesale-long-yellow-zinc-countersunk-wafer-torx-building-timber-wood/)

Compound Slot · DIN

**US$0.012 – 0.036**MOQ 5,000 pieces

[![Anti-Vibration Screws Vibration-Resistant Screws for Mounting Components Within Appliances](https://img.engineeringhardware.com/Anti-Vibration-Screws-Vibration-Resistant-Screws-for-Mounting-Components-Within-Appliances.webp)](https://engineeringhardware.com/product/anti-vibration-screws-vibration-resistant-screws-for-mounting-components-within/)

Countersunk & Flat-Head Machine Screws

### [Anti-Vibration Screws Vibration-Resistant Screws for Mounting Components Within Appliances](https://engineeringhardware.com/product/anti-vibration-screws-vibration-resistant-screws-for-mounting-components-within/)

Countersunk Head · DIN, GB, ANSI, JIS

**US$0.072 – 0.096**MOQ 5,000 pieces

[![M3 M4 M5 M6 M8 M10 SS304 Conical Solid Countersunk Head Washer Flat Gasket Concave and Convex Tapered Conical Washers](https://img.engineeringhardware.com/M3-M4-M5-M6-M8-M10-SS304-Conical-Solid-Countersunk-Head-Washer-Flat-Gasket-Concave-and-Convex-Tapered-Conical-Washers.webp)](https://engineeringhardware.com/product/m3-m4-m5-m6-m8-m10-ss304-conical-solid-countersunk-head-washer-flat-gasket-concave/)

Countersunk & Flat-Head Machine Screws

### [M3 M4 M5 M6 M8 M10 SS304 Conical Solid Countersunk Head Washer Flat Gasket Concave and Convex Tapered Conical Washers](https://engineeringhardware.com/product/m3-m4-m5-m6-m8-m10-ss304-conical-solid-countersunk-head-washer-flat-gasket-concave/)

Stainless Steel · ISO, ROHS, SGS

**US$0.0012**MOQ 100,000 pieces

[![Open All Stainless Steel Flat Head Aluminum Blind Rivet Countersunk Head Pull Rivet](https://img.engineeringhardware.com/Open-All-Stainless-Steel-Flat-Head-Aluminum-Blind-Rivet-Countersunk-Head-Pull-Rivet.webp)](https://engineeringhardware.com/product/open-all-stainless-steel-flat-head-aluminum-blind-rivet-countersunk-head-pull-rivet/)

Countersunk & Flat-Head Machine Screws

### [Open All Stainless Steel Flat Head Aluminum Blind Rivet Countersunk Head Pull Rivet](https://engineeringhardware.com/product/open-all-stainless-steel-flat-head-aluminum-blind-rivet-countersunk-head-pull-rivet/)

DIN7337 · Aluminum

**US$0.036 – 0.06**MOQ 1,000 pieces

[![Stainless Steel Metric Zinc Plated Flat Head Machine Screws M5 M10 M12](https://img.engineeringhardware.com/Stainless-Steel-Metric-Zinc-Plated-Flat-Head-Machine-Screws-M5-M10-M12.webp)](https://engineeringhardware.com/product/stainless-steel-metric-zinc-plated-flat-head-machine-screws-m5-m10-m12/)

Countersunk & Flat-Head Machine Screws

### [Stainless Steel Metric Zinc Plated Flat Head Machine Screws M5 M10 M12](https://engineeringhardware.com/product/stainless-steel-metric-zinc-plated-flat-head-machine-screws-m5-m10-m12/)

Countersunk Head · Stainless Steel

**US$0.12 – 0.18**MOQ 100 pieces

[![China Screw Manufacturer Flat Head Screw Machine Screw OEM Auto Part](https://img.engineeringhardware.com/China-Screw-Manufacturer-Flat-Head-Screw-Machine-Screw-OEM-Auto-Part.webp)](https://engineeringhardware.com/product/china-screw-manufacturer-flat-head-screw-machine-screw-oem-auto-part/)

Countersunk & Flat-Head Machine Screws

### [China Screw Manufacturer Flat Head Screw Machine Screw OEM Auto Part](https://engineeringhardware.com/product/china-screw-manufacturer-flat-head-screw-machine-screw-oem-auto-part/)

GB, ANSI, DIN, UNI, JIS and ISO · Stainless Steel

**US$1.08 – 32.40**MOQ 5,000 pieces

[View all Countersunk & Flat-Head Machine Screws →](https://engineeringhardware.com/fastener-products/screws/countersunk-flat-head-machine-screws/) [Full product catalog](https://engineeringhardware.com/products/)

## How to Specify Oval-Head Sheet-Metal Screws for Your Application

- **Size:** Match the nominal size to the mating thread or hole. This product spans 4–6; check the full table below for the exact dimensions of each size.
- **Drive & head:** Pick the drive (socket, cross, slot) and head style for the tool access and seating surface; a recessed drive resists cam-out under power tools.
- **Environment:** For damp, coastal or chemical exposure prefer A4/316 stainless or a suitable coating; indoors, plated steel or A2 is usually sufficient.
- **Standard:** This product is supplied to Trade series (oval sheet-metal screws). Quoting the standard on your order guarantees interchangeable dimensions between suppliers.

## Installation & Assembly Practice

- Match the driver exactly to the recess (PH ≠ PZ; hex key sizes per ISO 2936) and keep the tool axial — side load is the main cause of stripped drives.
- In tapped holes, engage a thread length of at least 1× the nominal diameter in steel, 2× in aluminum.
- Set power tools to a torque that seats the head without embedding it into the mating surface.

## Common Selection Mistakes with Oval-Head Sheet-Metal Screws

- Under-sizing the drive for the installation torque — a small recess at high torque strips before the screw is seated.
- Using a countersunk head in thin sheet where the countersink removes most of the load-bearing material.
- Specifying stainless in high-strength duty: A2-70 is roughly class 7 steel, not a 10.9 substitute.

## Where Oval-Head Sheet-Metal Screws Are Not the Right Choice

Not for high-preload structural joints (use a property-class bolt and nut), and not in thin sheet where a self-drilling or self-tapping type suits better.

Custom manufacturing · Made to drawing

## Need a oval-head sheet-metal screws outside the standard range?

Dimensions, material, finish and form are specified from the drawing — a screw outside the standard range is a variation on existing tooling rather than a new design. Made by cold heading or warm forging.

Minimum order from 2,000 pieces; samples within 7 days of drawing approval.

[Custom screw manufacturing](https://engineeringhardware.com/custom/screws/)[Send a drawing](https://engineeringhardware.com/custom/screws/#rfq)

## Technical Drawing

Dimensioned line drawing of #4 Oval-Head Sheet-Metal Screws to Trade series (oval sheet-metal screws). Side view and top view, drawn to the dimensions in the table below and redrawn for any size selected.

- **Head diameter (in):** 0.212
- **Head height (in):** 0.104
- **Drive:** No. 1
- **Thread pitch:** 24 TPI
- **Length options (in):** 3/8~1
- **Material:** 18-8 stainless steel

## Dimensions & Specifications (Trade series (oval sheet-metal screws))

| Size example | Head diameter (in) | Head height (in) | Drive | Thread pitch | Length options (in) | Material |
| --- | --- | --- | --- | --- | --- | --- |
| #4 | 0.212 | 0.104 | No. 1 | 24 TPI | 3/8~1 | 18-8 stainless steel |
| #6 | 0.262 | 0.128 | No. 2 | 18 TPI | 3/8~1 | 18-8 stainless steel |

Inside the plant

## Manufactured in our own plant

This part is cold-formed, threaded, heat-treated and finished in-house. The stages below are where its class and finish are actually decided.

1. ![Wire rod feeding into a cold heading machine](https://engineeringhardware.com/wp-content/uploads/2026/08/09-wire-rod-feed-cold-heading-machine.webp) 01 **Cold heading** Wire rod is drawn to size and cold-formed into blanks. Forming rather than cutting keeps the grain flow continuous around the head, which is where a bolt is most likely to fail. Head dimensions and under-head radius checked at set-up and per shift.
2. ![Thread rolling machine producing bolt threads](https://engineeringhardware.com/wp-content/uploads/2026/08/03-thread-rolling-machine-bolt-production.webp) 02 **Thread rolling** Threads are rolled between hardened dies rather than cut. Rolled threads are stronger in fatigue than cut threads and hold pitch and flank angle far more consistently across a batch. Go / no-go ring gauges to ISO 965 tolerance class 6g.
3. ![Baskets of bolts staged for heat treatment](https://engineeringhardware.com/wp-content/uploads/2026/08/05-heat-treatment-baskets-black-bolts.webp) 03 **Heat treatment** Quench-and-temper brings carbon and alloy steel to the property class ordered — 8.8, 10.9 or 12.9 — with the furnace charge tracked so a finished lot can be traced back to it. Core hardness and tensile tested per lot to ISO 898-1.
4. ![Zinc plated bolts in a treatment basket](https://engineeringhardware.com/wp-content/uploads/2026/08/23-zinc-plated-bolts-treatment-basket.webp) 04 **Surface treatment** Zinc, zinc-nickel, hot-dip galvanizing, black oxide, phosphate and Dacromet, selected against the service environment rather than against the price list. Coating thickness and neutral salt spray hours to ISO 9227.

## Frequently Asked Questions

### What drive type do Oval-Head Sheet-Metal Screws use?

Drive depends on the head style — socket (hex key), cross (Phillips/Pozi) or slot. A recessed drive resists cam-out when driven with power tools; check the product head style on this page.

### What material should Oval-Head Sheet-Metal Screws be for outdoor use?

For damp, coastal or chemical environments specify A4 (316) stainless or a suitably coated steel. For indoor or dry use, A2 (304) stainless or zinc-plated steel is normally adequate.

### Are Oval-Head Sheet-Metal Screws made to a recognized standard?

Yes — they are manufactured to Trade series (oval sheet-metal screws), so dimensions are interchangeable between suppliers when you quote the standard on your order.

### What are Oval-Head Sheet-Metal Screws used for?

Forming a thread in sheet metal while retaining an oval head that sits into a shallow countersink. They are supplied to Trade series (oval sheet-metal screws).

### Can I get a quote for Oval-Head Sheet-Metal Screws in the size and material I need?

Yes. Use the technical drawing and quote form on this page to set the size and options, then send the exact configuration to our team for pricing and lead time.

## Related Pages

Product page: [Oval-Head Sheet-Metal Screws — specifications & sizes](https://engineeringhardware.com/fastener/oval-head-sheet-metal-screws/)

### Oval-Head Sheet-Metal Screws Specification Guides

### Related Fastener Applications