---
title: "What Are Push-Barb Cable Tie Mounts Used For?"
description: "Push-Barb Cable Tie Mounts (Trade series (push-in barbed tie mounts)) are used for routing, bundling and strain-relieving cable at a panel entry or a fixing…"
url: https://engineeringhardware.com/applications/push-barb-cable-tie-mounts/
source: Engineering Hardware & Fasteners
---

# What Are Push-Barb Cable Tie Mounts Used For?

Cable & Cord Management · Trade series (push-in barbed tie mounts) · Application guide

Typical applications, the industries that specify push-barb cable tie mounts, and how to choose the right size, material and finish for the joint.

Push-Barb Cable Tie Mounts are used for routing, bundling and strain-relieving cable at a panel entry or a fixing point. They are manufactured to Trade series (push-in barbed tie mounts), and selection is driven by the nominal size, the fit and tolerance the assembly requires, and the service environment.

- **Primary duty:** Routing, bundling and strain-relieving cable at a panel entry or a fixing point
- **Governing standard:** Trade series (push-in barbed tie mounts)
- **Category:** Cable & Cord Management

Application notes are general engineering guidance. Verify the property class and any approval requirement against your own design calculation.

![What Are Push-Barb Cable Tie Mounts Used For? application image](https://engineeringhardware.com/wp-content/uploads/2026/09/Push-Barb-Cable-Tie-Mounts.webp)

Push-Barb Cable Tie Mounts are used primarily for routing, bundling and strain-relieving cable at a panel entry or a fixing point. This page lists the industries and assemblies where they are specified, the selection criteria that matter for each application, installation practice, and the cases where a different fastener type is the correct choice. Parts are supplied to Trade series (push-in barbed tie mounts).

## Typical Applications for Push-Barb Cable Tie Mounts

The most common settings where these are specified:

- **General machine building:** fastening covers, brackets, motors and sub-assemblies on production equipment.
- **Maintenance & repair (MRO):** a stocked size for servicing existing plant where the original fastener spec must be matched.
- **Fabrication & metalwork:** bench and on-site assembly of steel frames, enclosures and weldments.

Product catalog

## Related Cable Tie Mounts products

[![Single Bolt Cable Clamp Stainless Steel 2-10mm Simplex Wire Rope Clip](https://img.engineeringhardware.com/Single-Bolt-Cable-Clamp-Stainless-Steel-2-10mm-Simplex-Wire-Rope-Clip.webp)](https://engineeringhardware.com/product/single-bolt-cable-clamp-stainless-steel-2-10mm-simplex-wire-rope-clip/)

Pipe, Tube, Beam & Cable Clamps

### [Single Bolt Cable Clamp Stainless Steel 2-10mm Simplex Wire Rope Clip](https://engineeringhardware.com/product/single-bolt-cable-clamp-stainless-steel-2-10mm-simplex-wire-rope-clip/)

Standard · Stainless Steel

**US$0.18 – 3.60**MOQ 1,000 pieces

[![Electrical Insulated Cable Clamp Insulation 2 Bolt Piercing Connectors](https://img.engineeringhardware.com/Electrical-Insulated-Cable-Clamp-Insulation-2-Bolt-Piercing-Connectors.webp)](https://engineeringhardware.com/product/electrical-insulated-cable-clamp-insulation-2-bolt-piercing-connectors/)

Pipe, Tube, Beam & Cable Clamps

### [Electrical Insulated Cable Clamp Insulation 2 Bolt Piercing Connectors](https://engineeringhardware.com/product/electrical-insulated-cable-clamp-insulation-2-bolt-piercing-connectors/)

Terminal Clamp · GB

**US$1.31 – 1.68**MOQ 200 pieces

[![Tiger Beam Clamp for Screw Rod Hanger Brace of Steel Structure M10/M12 Cast Steel Jaws Clamp](https://img.engineeringhardware.com/Tiger-Beam-Clamp-for-Screw-Rod-Hanger-Brace-of-Steel-Structure-M10-M12-Cast-Steel-Jaws-Clamp.webp)](https://engineeringhardware.com/product/tiger-beam-clamp-for-screw-rod-hanger-brace-of-steel-structure-m10-m12-cast-steel/)

Pipe, Tube, Beam & Cable Clamps

### [Tiger Beam Clamp for Screw Rod Hanger Brace of Steel Structure M10/M12 Cast Steel Jaws Clamp](https://engineeringhardware.com/product/tiger-beam-clamp-for-screw-rod-hanger-brace-of-steel-structure-m10-m12-cast-steel/)

Beam Clamps · GB, ASTM, DIN, JIS, AISI, BS

**US$0.012 – 5.99**MOQ 1 piece

[![PVC Pipe Clamp for Garden Water Pipes Locking Tube Holder Snap Clip](https://img.engineeringhardware.com/PVC-Pipe-Clamp-for-Garden-Water-Pipes-Locking-Tube-Holder-Snap-Clip.webp)](https://engineeringhardware.com/product/pvc-pipe-clamp-for-garden-water-pipes-locking-tube-holder-snap-clip/)

Pipe, Tube, Beam & Cable Clamps

### [PVC Pipe Clamp for Garden Water Pipes Locking Tube Holder Snap Clip](https://engineeringhardware.com/product/pvc-pipe-clamp-for-garden-water-pipes-locking-tube-holder-snap-clip/)

GB/ASTM/DIN/BS · Plastic

**US$0.22 – 0.36**MOQ 3,000 pieces

[![No Welding Stainless Steel Pipe Repair Clamp for PE PVC Pipe Pipe Clamp Single- Clip-Type](https://img.engineeringhardware.com/No-Welding-Stainless-Steel-Pipe-Repair-Clamp-for-PE-PVC-Pipe-Pipe-Clamp-Single-Clip-Type.webp)](https://engineeringhardware.com/product/no-welding-stainless-steel-pipe-repair-clamp-for-pe-pvc-pipe-pipe-clamp-single-clip/)

Pipe, Tube, Beam & Cable Clamps

### [No Welding Stainless Steel Pipe Repair Clamp for PE PVC Pipe Pipe Clamp Single- Clip-Type](https://engineeringhardware.com/product/no-welding-stainless-steel-pipe-repair-clamp-for-pe-pvc-pipe-pipe-clamp-single-clip/)

Standard · Stainless Steel

**US$1.20 – 48.00**MOQ 10 pieces

[![FTTH Optical Cable Accessories Odwac-22p Drop Cable Clamp](https://img.engineeringhardware.com/FTTH-Optical-Cable-Accessories-Odwac-22p-Drop-Cable-Clamp.webp)](https://engineeringhardware.com/product/ftth-optical-cable-accessories-odwac-22p-drop-cable-clamp/)

Pipe, Tube, Beam & Cable Clamps

### [FTTH Optical Cable Accessories Odwac-22p Drop Cable Clamp](https://engineeringhardware.com/product/ftth-optical-cable-accessories-odwac-22p-drop-cable-clamp/)

Stainless Steel and UV-Resistant Plastic Component · FTTH / FTTB / FTT…

**US$0.42 – 0.46**MOQ 1,002 pieces

[View all Pipe, Tube, Beam & Cable Clamps →](https://engineeringhardware.com/fastener-products/clamps-clips-cable-ties/pipe-tube-beam-cable-clamps/) [Full product catalog](https://engineeringhardware.com/products/)

## How to Specify Push-Barb Cable Tie Mounts for Your Application

- **Size:** Match the size to the mating part — see the dimension table below for each option.
- **Material:** Choose the material and finish for the service environment — plated steel for general use, stainless for corrosion resistance.
- **Environment:** For damp, coastal or chemical exposure prefer A4/316 stainless or a suitable coating; indoors, plated steel or A2 is usually sufficient.
- **Standard:** This product is supplied to Trade series (push-in barbed tie mounts). Quoting the standard on your order guarantees interchangeable dimensions between suppliers.

## Where Push-Barb Cable Tie Mounts Are Not the Right Choice

Match the fastener to the load, environment and whether the joint must be reopened; the wrong class or style is the usual cause of joint failure.

Custom manufacturing · Made to drawing

## Need a push-barb cable tie mounts outside the standard range?

The geometry is whatever the drawing says. A machined component has no standard to depart from, so the drawing and the tolerance scheme are the whole specification.

Minimum order from 2,000 pieces; samples within 7 days of drawing approval.

[Custom cable management manufacturing](https://engineeringhardware.com/custom/cable-management/)[Send a drawing](https://engineeringhardware.com/custom/cable-management/#rfq)

## Technical Drawing

Dimensioned line drawing of barbed push-in stem Push-Barb Cable Tie Mounts to Trade series (push-in barbed tie mounts). Side view and top view, drawn to the dimensions in the table below and redrawn for any size selected.

- **Panel access needed:** front only
- **Selected by:** panel hole diameter and panel thickness
- **Reusable:** no

## Dimensions & Specifications (Trade series (push-in barbed tie mounts))

| Fixing | Panel access needed | Selected by | Reusable |
| --- | --- | --- | --- |
| barbed push-in stem | front only | panel hole diameter and panel thickness | no |
| barbed push-in stem with disc | front only | panel hole diameter and panel thickness | no |
| arrowhead push-in stem | front only | panel hole diameter and panel thickness | no |

Inside the plant

## Manufactured in our own plant

This part is cold-formed, threaded, heat-treated and finished in-house. The stages below are where its class and finish are actually decided.

1. ![Wire rod feeding into a cold heading machine](https://engineeringhardware.com/wp-content/uploads/2026/08/09-wire-rod-feed-cold-heading-machine.webp) 01 **Cold heading** Wire rod is drawn to size and cold-formed into blanks. Forming rather than cutting keeps the grain flow continuous around the head, which is where a bolt is most likely to fail. Head dimensions and under-head radius checked at set-up and per shift.
2. ![Thread rolling machine producing bolt threads](https://engineeringhardware.com/wp-content/uploads/2026/08/03-thread-rolling-machine-bolt-production.webp) 02 **Thread rolling** Threads are rolled between hardened dies rather than cut. Rolled threads are stronger in fatigue than cut threads and hold pitch and flank angle far more consistently across a batch. Go / no-go ring gauges to ISO 965 tolerance class 6g.
3. ![Baskets of bolts staged for heat treatment](https://engineeringhardware.com/wp-content/uploads/2026/08/05-heat-treatment-baskets-black-bolts.webp) 03 **Heat treatment** Quench-and-temper brings carbon and alloy steel to the property class ordered — 8.8, 10.9 or 12.9 — with the furnace charge tracked so a finished lot can be traced back to it. Core hardness and tensile tested per lot to ISO 898-1.
4. ![Zinc plated bolts in a treatment basket](https://engineeringhardware.com/wp-content/uploads/2026/08/23-zinc-plated-bolts-treatment-basket.webp) 04 **Surface treatment** Zinc, zinc-nickel, hot-dip galvanizing, black oxide, phosphate and Dacromet, selected against the service environment rather than against the price list. Coating thickness and neutral salt spray hours to ISO 9227.

## Frequently Asked Questions

### What are Push-Barb Cable Tie Mounts used for?

Routing, bundling and strain-relieving cable at a panel entry or a fixing point. They are supplied to Trade series (push-in barbed tie mounts).

### Which industries use Push-Barb Cable Tie Mounts?

They are commonly specified in general machine building, maintenance & repair (mro) and fabrication & metalwork, among other sectors.

### How do I choose the right size of Push-Barb Cable Tie Mounts?

Match the size to the mating part using the dimension table on this page.

### Are Push-Barb Cable Tie Mounts made to a recognized standard?

Yes — they are manufactured to Trade series (push-in barbed tie mounts), so dimensions are interchangeable between suppliers when you quote the standard on your order.

### Can I get a quote for Push-Barb Cable Tie Mounts in the size and material I need?

Yes. Use the technical drawing and quote form on this page to set the size and options, then send the exact configuration to our team for pricing and lead time.

## Related Pages

Product page: [Push-Barb Cable Tie Mounts — specifications & sizes](https://engineeringhardware.com/fastener/push-barb-cable-tie-mounts/)

### Push-Barb Cable Tie Mounts Specification Guides

### Related Fastener Applications