--- title: "Full-Length Grooved Pins with Pilot" description: "Full-Length Grooved Pins with Pilot to ISO 8739: full dimensional table. 13 catalogued sizes with materials and finishes." url: https://engineeringhardware.com/fastener/iso-8739-full-length-grooved-pin-with-pilot/ source: Engineering Hardware & Fasteners --- # Full-Length Grooved Pins with Pilot Pins · Grooved Pins 13 catalogued sizes, dimensioned to ISO 8739. Pick any row and the technical drawing redraws to it. Full-Length Grooved Pins with Pilot to ISO 8739: the full dimensional table is reproduced below. 13 sizes are held in the table below, and the technical drawing redraws to whichever row you select. - **Standard:** ISO 8739 - **Catalogued sizes:** 13 Dimensions are nominal values from the governing standard. Confirm the tolerance class for your application before ordering. ![Full-Length Grooved Pins with Pilot technical product image](https://engineeringhardware.com/wp-content/uploads/2026/09/iso-8739-full-length-grooved-pin-with-pilot.webp) ## Materials & Grades Select a material class to see the grades we supply it in. Each designation is listed with its ISO/EN, AISI/SAE, JIS and GB equivalents. Stainless Steel38 Carbon Steel66 Alloy Steel41 Bearing Steel5 Spring Steel25 Aluminum and Aluminum Alloys21 Brass17 Bronze11 Copper8 Titanium and Titanium Alloys18 Nickel and Nickel Alloys22 Iron-Nickel and High-Temperature Alloys10 Tool Steel and Specialty Hardened Steel9 Structural and Construction Steel9 ### Stainless Steel #### Austenitic Stainless Steel - A1 AISI 303 · SAE 303 · SUS303 · EN 1.4305 · X8CrNiS18-9 - A2 AISI 304 · SAE 304 · SUS304 · EN 1.4301 · X5CrNi18-10 · 06Cr19Ni10 - 304L AISI 304L · SUS304L · EN 1.4307 · X2CrNi18-9 · 022Cr19Ni10 - 302 AISI 302 · SUS302 · EN 1.4310 - 305 AISI 305 · SUS305 · EN 1.4303 - A4 AISI 316 · SAE 316 · SUS316 · EN 1.4401 · X5CrNiMo17-12-2 · 06Cr17Ni12Mo2 - 316L AISI 316L · SUS316L · EN 1.4404 · X2CrNiMo17-12-2 · 022Cr17Ni12Mo2 - 321 AISI 321 · SUS321 · EN 1.4541 · X6CrNiTi18-10 - 310 / 310S AISI 310 · AISI 310S · SUS310S · EN 1.4845 - 302HQ AISI 302HQ - A3 - A5 - 347 AISI 347 · SUS347 · EN 1.4550 · X6CrNiNb18-10 - 309 / 309S AISI 309 · AISI 309S · SUS309S #### Martensitic Stainless Steel - AISI 410 SUS410 · EN 1.4006 · X12Cr13 · 12Cr13 - AISI 420 SUS420J1 · SUS420J2 · EN 1.4021 · EN 1.4028 · 20Cr13 · 30Cr13 - AISI 431 SUS431 · EN 1.4057 · X17CrNi16-2 - C1 - C3 - C4 - AISI 440A - AISI 440B - AISI 440C SUS440C · EN 1.4125 #### Ferritic Stainless Steel - AISI 430 SUS430 · EN 1.4016 · X6Cr17 · 10Cr17 - F1 - AISI 434 - AISI 444 #### Precipitation-Hardening Stainless Steel - 17-4 PH AISI 630 · UNS S17400 · SUS630 · EN 1.4542 · X5CrNiCuNb16-4 - 15-5 PH UNS S15500 - 17-7 PH UNS S17700 #### Duplex and Super Duplex Stainless Steel - Duplex 2205 UNS S31803 · UNS S32205 · EN 1.4462 - Super Duplex 2507 UNS S32750 · EN 1.4410 - D2 - D4 - D6 - D8 - Lean Duplex 2101 UNS S32101 - Super Duplex S32760 UNS S32760 · EN 1.4501 ### Carbon Steel #### Low-Carbon Steel - SAE 1006 - SAE 1008 - SAE 1010 - SAE 1018 - SAE 1020 - Q195 - Q235 - SAE 1012 - SAE 1015 - Q215 - ML08 - ML08Al - ML10 - ML15 - ML20 - SWRCH6A - SWRCH8A - SWRCH10A - SWRCH12A - SWRCH15A - SWRCH18A #### Medium-Carbon Steel - SAE 1035 - SAE 1045 - S45C - C45 - SAE 1030 - SAE 1040 - SAE 1050 - 30 - 35 - 40 - 45 - 50 - S35C - S40C - S50C - C35 - C40 #### High-Carbon Steel - SAE 1060 - SAE 1070 - 65Mn - SAE 1065 - SAE 1075 - SAE 1080 - SAE 1085 - SAE 1090 - SAE 1095 - 60 - 65 - 70 - 75 - 80 - 85 #### Cold-Heading Steel - SWRCH22A - 10B21 - SWRCH22K - SWRCH25K - SWRCH30K - SWRCH35K - SWRCH40K - ML20Mn - ML25 - ML30 - ML35 - ML40 - 15B25 ### Alloy Steel #### Chromium Steel - 40Cr - 45Cr - AISI 5140 - SAE 5140 - AISI 5120 - SAE 5120 - SCr420 - SCr440 #### Chromium-Molybdenum Steel - 35CrMo - 42CrMo - AISI 4140 - SCM435 - SCM440 - 42CrMo4 - 30CrMo - AISI 4130 - SAE 4130 - SAE 4140 - AISI 4142 - AISI 4145 - SCM415 - SCM420 - SCM445 - EN 1.7220 - EN 1.7225 - 25CrMo4 - 34CrMo4 #### Nickel-Chromium-Molybdenum Steel - AISI 4340 - SAE 4340 - 40CrNiMo - SNCM439 - EN 1.6511 - 36CrNiMo4 #### Boron Alloy Steel - 10B22 - 10B21 - 15B21 - 15B25 - 20MnTiB - 20Mn2B - 35VB - 40MnB ### Bearing Steel #### Bearing Steel - GCr15 - AISI 52100 SAE 52100 · UNS G52986 - SUJ2 - 100Cr6 EN 1.3505 - GCr15SiMn ### Spring Steel #### Carbon Spring Steel - SAE 1065 - SAE 1070 - SAE 1075 - SAE 1080 - SAE 1095 - 65 - 70 - 75 - 80 - 65Mn #### Silicon-Manganese Spring Steel - 60Si2Mn - 60Si2MnA - SUP6 - SUP7 #### Chromium-Vanadium Spring Steel - 50CrVA - SAE 6150 - AISI 6150 - SUP10 #### Stainless Spring Steel - AISI 301 - SUS301 - EN 1.4310 - AISI 302 - AISI 304 - AISI 316 - 17-7 PH ### Aluminum and Aluminum Alloys #### Commercially Pure Aluminum - 1050 - 1060 - 1070 - 1100 #### 2xxx Series Aluminum - 2024 - 2011 - 2014 - 2017 #### 5xxx Series Aluminum - 5052 - 5083 - 5754 #### 6xxx Series Aluminum - 6061 - 6061-T6 - 6063 - 6082 - 6082-T6 #### 7xxx Series Aluminum - 7075 - 7075-T6 - 7005 - 7050 - 7075-T73 ### Brass #### Free-Cutting Brass - C36000 - H62 - HPb59-1 - C3601 - C3602 - C3604 - CuZn36Pb3 - CuZn39Pb3 - EN CW614N - EN CW617N - H65 #### Lead-Free Brass - C69300 - C27450 - CW510L - CW511L #### Naval Brass - C46400 - CuZn39Sn1 ### Bronze #### Silicon Bronze - C65500 - C65100 - C65600 #### Phosphor Bronze - C51000 - C52100 - CuSn6 - CuSn8 #### Aluminum Bronze - C95400 - C95500 - C63000 - CuAl10Ni5Fe4 ### Copper #### Copper - C11000 - T2 - C10100 - C10200 - C12200 - T1 - TU1 - TU2 ### Titanium and Titanium Alloys #### Commercially Pure Titanium - Grade 2 - Grade 1 - Grade 3 - Grade 4 - TA1 - TA2 - TA3 #### Alpha-Beta Titanium Alloys - Grade 5 - Ti-6Al-4V - TC4 - UNS R56400 #### Low-Interstitial Grade - Grade 23 - Ti-6Al-4V ELI - UNS R56407 #### Other Titanium Fastener Alloys - Ti-6Al-6V-2Sn - Ti-6Al-2Sn-4Zr-2Mo - Beta-C titanium - Ti-10V-2Fe-3Al ### Nickel and Nickel Alloys #### Commercially Pure Nickel - Nickel 200 - UNS N02200 - Nickel 201 - UNS N02201 #### Inconel Alloys - Inconel 625 UNS N06625 - Inconel 718 UNS N07718 - Inconel 600 UNS N06600 - Inconel 601 UNS N06601 - Inconel 686 UNS N06686 - Inconel X-750 UNS N07750 #### Monel Alloys - Monel 400 UNS N04400 - Monel K-500 UNS N05500 #### Hastelloy Alloys - Hastelloy C-276 UNS N10276 - Hastelloy C-22 UNS N06022 - Hastelloy B-2 UNS N10665 - Hastelloy B-3 UNS N10675 - Hastelloy X UNS N06002 #### Other Nickel Alloys - Alloy 20 UNS N08020 - Alloy 625 - Alloy 718 - Alloy 825 UNS N08825 - Alloy 925 UNS N09925 ### Iron-Nickel and High-Temperature Alloys #### A286 - A-286 - UNS S66286 - EN 1.4980 #### Invar - Invar 36 - Alloy 36 - UNS K93600 - FeNi36 #### Alloy 42 - Alloy 42 - UNS K94100 - FeNi42 ### Tool Steel and Specialty Hardened Steel #### Tool Steel and Specialty Hardened Steel - AISI D2 - AISI H13 - SKD11 - Cr12MoV - AISI O1 - AISI A2 - AISI S7 - SKD61 - 9CrSi ### Structural and Construction Steel #### Structural and Construction Steel - ASTM A36 - Q235B - Q355B - S355JR - Q235C - Q355C - S235JR - S275JR - S355J2 ## Applications & Industries Where Full-Length Grooved Pins with Pilot are used, and what decides the specification in each case. Stocked from 1.5 mm to 25 mm (nominal diameter). ### Industries that specify Full-Length Grooved Pins with Pilot - **Appliances:** pivots and levers. - **Automotive:** hinges and linkages. - **Mechanisms:** gear and hub fixing. - **Toys and consumer goods:** shafts in plastic parts. - **Jigs, tooling & fixtures:** Locating plates and tooling so they reassemble in the same position. - **Machine building:** Hinges, pivots and linkages carrying light to moderate shear. ### Typical applications - fixing without reaming the hole - starting straight with the pilot end - retaining parts by the rolled grooves - high-volume press assembly - pivot and hinge joints loaded in shear - quick connections made and broken by hand ### Service conditions to specify against - **Marine and coastal:** Available in A4 (316) stainless for chloride exposure — coastal structures, pool halls, water treatment and deck hardware, where A2 will eventually pit. - **Hole preparation:** The hole is half the specification: a ground dowel needs a reamed H7 hole, a grooved or spring pin will hold in a drilled one. ### Where to use something else - Do not re-use a grooved pin after removal; the grooves flatten and hold is lost. [Full application guide: where Full-Length Grooved Pins with Pilot are used, how to specify them, and the cases they are wrong for](https://engineeringhardware.com/applications/iso-8739-full-length-grooved-pin-with-pilot/) ## Technical Drawing Dimensioned line drawing of 1.5 mm Full-Length Grooved Pins with Pilot to ISO 8739. Side view and top view, drawn to the dimensions in the table below and redrawn for any size selected. - **d_1 (mm):** 1.5 - **d_2 (mm):** 1.6 - **c (mm):** 1.5 - **a (mm):** 0.2 - **Length range l (mm):** 8~20 ## Dimensions & Specifications (ISO 8739) Every row below is a starting point for the customizer above — pick any size and the drawing will redraw to that row. | Nominal diameter d (mm) | d_1 (mm) | d_2 (mm) | c (mm) | a (mm) | Length range l (mm) | Reference standard | | --- | --- | --- | --- | --- | --- | --- | | 1.5 mm | 1.5 | 1.6 | 1.5 | 0.2 | 8~20 | ISO 8739 | | 2 mm | 2 | 2.15 | 1.5 | 0.25 | 8~30 | ISO 8739 | | 2.5 mm | 2.5 | 2.65 | 2 | 0.3 | 10~30 | ISO 8739 | | 3 mm | 3 | 3.2 | 2 | 0.4 | 10~40 | ISO 8739 | | 4 mm | 4 | 4.25 | 2.5 | 0.5 | 10~60 | ISO 8739 | | 5 mm | 5 | 5.25 | 2.5 | 0.63 | 14~60 | ISO 8739 | | 6 mm | 6 | 6.3 | 3.5 | 0.8 | 14~80 | ISO 8739 | | 8 mm | 8 | 8.3 | 3.5 | 1 | 14~100 | ISO 8739 | | 10 mm | 10 | 10.35 | 4.5 | 1.2 | 14~100 | ISO 8739 | | 12 mm | 12 | 12.35 | 4.5 | 1.6 | 18~100 | ISO 8739 | | 16 mm | 16 | 16.4 | 4.5 | 2 | 22~100 | ISO 8739 | | 20 mm | 20 | 20.5 | 6.5 | 2.5 | 26~100 | ISO 8739 | | 25 mm | 25 | 25.5 | 6.5 | 3 | 26~100 | ISO 8739 | Full-Length Grooved Pins with Pilot conform to ISO 8739. As pins, they are specified by the dimensions in the table below; this page also covers materials, finishes and typical uses. ## What Are Full-Length Grooved Pins with Pilot? Full-Length Grooved Pins with Pilot are pins defined by ISO 8739. They are selected by nominal diameter and the dimensional characteristics shown below, and are available in a range of materials and finishes to suit the application and environment. ## Materials & Finishes Common materials include carbon steel (typically zinc plated or hot-dip galvanized), hardened or case-hardened steel where wear matters, and stainless steel A2 (304) or A4 (316) for corrosion resistance. Specify the material, hardness where relevant, and the surface finish appropriate to your application and environment. ## Specification Guides Each size, material and standard of Full-Length Grooved Pins with Pilot has its own reference page with the figures for that one configuration. ## Goes With Hardware commonly specified alongside Full-Length Grooved Pins with Pilot. ## Pricing Full-Length Grooved Pins with Pilot are supplied to order. Pricing starts from approximately US$0.050 per piece for standard sizes in carbon steel; final pricing depends on size, material, finish and order quantity (MOQ applies). Submit your exact configuration with the quote form above. Custom manufacturing · Made to drawing ## Need a full-length grooved pins with pilot outside the standard range? Tolerance class is what a special pin usually turns on — a locating pin and a retaining pin want very different fits in the same nominal size. Made by cold heading or turning. Minimum order from 2,000 pieces; samples within 7 days of drawing approval. [Custom pin manufacturing](https://engineeringhardware.com/custom/pins/)[Send a drawing](https://engineeringhardware.com/custom/pins/#rfq) Inside the plant ## Manufactured in our own plant This part is cold-formed, threaded, heat-treated and finished in-house. The stages below are where its class and finish are actually decided. 1. ![Wire rod feeding into a cold heading machine](https://engineeringhardware.com/wp-content/uploads/2026/08/09-wire-rod-feed-cold-heading-machine.webp) 01 **Cold heading** Wire rod is drawn to size and cold-formed into blanks. Forming rather than cutting keeps the grain flow continuous around the head, which is where a bolt is most likely to fail. Head dimensions and under-head radius checked at set-up and per shift. 2. ![Thread rolling machine producing bolt threads](https://engineeringhardware.com/wp-content/uploads/2026/08/03-thread-rolling-machine-bolt-production.webp) 02 **Thread rolling** Threads are rolled between hardened dies rather than cut. Rolled threads are stronger in fatigue than cut threads and hold pitch and flank angle far more consistently across a batch. Go / no-go ring gauges to ISO 965 tolerance class 6g. 3. ![Baskets of bolts staged for heat treatment](https://engineeringhardware.com/wp-content/uploads/2026/08/05-heat-treatment-baskets-black-bolts.webp) 03 **Heat treatment** Quench-and-temper brings carbon and alloy steel to the property class ordered — 8.8, 10.9 or 12.9 — with the furnace charge tracked so a finished lot can be traced back to it. Core hardness and tensile tested per lot to ISO 898-1. 4. ![Zinc plated bolts in a treatment basket](https://engineeringhardware.com/wp-content/uploads/2026/08/23-zinc-plated-bolts-treatment-basket.webp) 04 **Surface treatment** Zinc, zinc-nickel, hot-dip galvanizing, black oxide, phosphate and Dacromet, selected against the service environment rather than against the price list. Coating thickness and neutral salt spray hours to ISO 9227. ## Frequently Asked Questions ### What standard are Full-Length Grooved Pins with Pilot manufactured to? Full-Length Grooved Pins with Pilot are manufactured to ISO 8739. The dimensional values on this page follow that standard. ### What is the size range of Full-Length Grooved Pins with Pilot? The table on this page lists 13 sizes for Full-Length Grooved Pins with Pilot, ranging from 1.5 mm to 25 mm. Sizes outside the table can be quoted on request. ### In which materials are Full-Length Grooved Pins with Pilot supplied? Full-Length Grooved Pins with Pilot are supplied in hardened alloy steel and stainless, with finishes including zinc plating, hot-dip galvanizing and black oxide. Choose material and finish to suit the load and the service environment for Full-Length Grooved Pins with Pilot. ### How do I request a quotation? Use the parametric drawing on this page to set the exact configuration (size, material, finish) and click "Request this configuration" — a specialist from Engineering Hardware will respond within one business day.