Slotted Round Nut manufactured in A2 Stainless Steel (ISO 3506 group A2 (304 / 1.4301), commonly supplied A2-70) are dimensioned to GB/T 812. The sections below give the mechanical and physical properties of the grade, its behavior in corrosive and elevated-temperature service, and the full size table.
Why Choose A2 Stainless Steel for Slotted Round Nut — GB/T 812 (Series 069)
The most common stainless group for indoor and general outdoor fasteners. For slotted round nut — gb/t 812 (series 069), this matters when good general corrosion resistance is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 3506 group A2 (304 / 1.4301), commonly supplied A2-70 |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C, subject to the property class and the joint |
| Corrosion characteristic | Good general corrosion resistance |
Corrosion Behavior in Service
A2 (304) gives excellent atmospheric and most-water corrosion resistance and is the most common stainless for Slotted Round Nut — GB/T 812 (Series 069) in indoor and general outdoor service. In chloride-bearing environments (marine air, road salt, swimming pools) consider stepping up to A4 (316).
Comparable Grades
For Slotted Round Nut — GB/T 812 (Series 069), the alternative stainless grade is A4 (316). A2 (304) suits general indoor and outdoor service; A4 (316) adds molybdenum for marine and chloride environments. Where higher strength matters more than corrosion, switch to plated alloy-steel class 8.8 or 10.9.
Using Stainless Fasteners in Aluminum
Stainless steel is more noble than aluminum, so in the presence of an electrolyte — rain, condensation, salt spray — the aluminum becomes the anode and corrodes at the joint. The effect is driven by the area ratio: a small stainless fastener in a large aluminum section is normally acceptable, while a large stainless fastener in thin aluminum is not. Where the joint is wet, isolate the two metals with a coated or nylon washer and a sealant, or specify an aluminum or coated fastener instead.
Sizes of Slotted Round Nut — GB/T 812 (Series 069) Available in A2 Stainless Steel
| Size | Pitch (mm) | Outer diameter D (mm) | Nut height m (mm) | Slot width (mm) | Slot depth (mm) | Reference standard |
|---|---|---|---|---|---|---|
| M10x1.0 | 1.0 | 18 | 8 | 3 | 2 | GB/T 812 / DIN 1804 |
| M12x1.25 | 1.25 | 22 | 8 | 3 | 2 | GB/T 812 / DIN 1804 |
| M16x1.5 | 1.5 | 28 | 8 | 4 | 2.5 | GB/T 812 / DIN 1804 |
| M20x1.5 | 1.5 | 34 | 10 | 4 | 2.5 | GB/T 812 / DIN 1804 |
| M24x1.5 | 1.5 | 40 | 10 | 5 | 3 | GB/T 812 / DIN 1804 |
| M30x1.5 | 1.5 | 48 | 12 | 5 | 3 | GB/T 812 / DIN 1804 |
| M36x1.5 | 1.5 | 58 | 12 | 6 | 3 | GB/T 812 / DIN 1804 |
| M48x1.5 | 1.5 | 72 | 15 | 6 | 4 | GB/T 812 / DIN 1804 |
| M60x2.0 | 2.0 | 90 | 18 | 7 | 4 | GB/T 812 / DIN 1804 |
| M80x2.0 | 2.0 | 115 | 20 | 8 | 5 | GB/T 812 / DIN 1804 |
| M100x2.0 | 2.0 | 140 | 22 | 10 | 5 | GB/T 812 / DIN 1804 |
