Flat Plain Washer manufactured in A2 Stainless Steel (ISO 3506 group A2 (304 / 1.4301), commonly supplied A2-70) are dimensioned to GB/T 95 / ISO 7091. The sections below give the mechanical and physical properties of the grade, its behavior in corrosive and elevated-temperature service, and the full size table.
Why Choose A2 Stainless Steel for Flat Plain Washer — GB/T 95 / ISO 7091 (Series 079)
The most common stainless group for indoor and general outdoor fasteners. For flat plain washer — gb/t 95 / iso 7091 (series 079), this matters when good general corrosion resistance is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 3506 group A2 (304 / 1.4301), commonly supplied A2-70 |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C, subject to the property class and the joint |
| Corrosion characteristic | Good general corrosion resistance |
Corrosion Behavior in Service
A2 (304) gives excellent atmospheric and most-water corrosion resistance and is the most common stainless for Flat Plain Washer — GB/T 95 / ISO 7091 (Series 079) in indoor and general outdoor service. In chloride-bearing environments (marine air, road salt, swimming pools) consider stepping up to A4 (316).
Comparable Grades
For Flat Plain Washer — GB/T 95 / ISO 7091 (Series 079), the alternative stainless grade is A4 (316). A2 (304) suits general indoor and outdoor service; A4 (316) adds molybdenum for marine and chloride environments. Where higher strength matters more than corrosion, switch to plated alloy-steel class 8.8 or 10.9.
Using Stainless Fasteners in Aluminum
Stainless steel is more noble than aluminum, so in the presence of an electrolyte — rain, condensation, salt spray — the aluminum becomes the anode and corrodes at the joint. The effect is driven by the area ratio: a small stainless fastener in a large aluminum section is normally acceptable, while a large stainless fastener in thin aluminum is not. Where the joint is wet, isolate the two metals with a coated or nylon washer and a sealant, or specify an aluminum or coated fastener instead.
Sizes of Flat Plain Washer — GB/T 95 / ISO 7091 (Series 079) Available in A2 Stainless Steel
| For bolt size | Inner diameter d1 (mm) | Outer diameter d2 (mm) | Thickness t (mm) | Reference standard |
|---|---|---|---|---|
| M3 | 3.2 | 7.0 | 0.5 | ISO 7089 / GB/T 97.1 |
| M4 | 4.3 | 9.0 | 0.8 | ISO 7089 / GB/T 97.1 |
| M5 | 5.3 | 10.0 | 1.0 | ISO 7089 / GB/T 97.1 |
| M6 | 6.4 | 12.0 | 1.6 | ISO 7089 / GB/T 97.1 |
| M8 | 8.4 | 16.0 | 1.6 | ISO 7089 / GB/T 97.1 |
| M10 | 10.5 | 20.0 | 2.0 | ISO 7089 / GB/T 97.1 |
| M12 | 13.0 | 24.0 | 2.5 | ISO 7089 / GB/T 97.1 |
| M14 | 15.0 | 28.0 | 2.5 | ISO 7089 / GB/T 97.1 |
| M16 | 17.0 | 30.0 | 3.0 | ISO 7089 / GB/T 97.1 |
| M18 | 19.0 | 34.0 | 3.0 | ISO 7089 / GB/T 97.1 |
| M20 | 21.0 | 37.0 | 3.0 | ISO 7089 / GB/T 97.1 |
| M24 | 25.0 | 44.0 | 4.0 | ISO 7089 / GB/T 97.1 |
| M30 | 31.0 | 56.0 | 4.0 | ISO 7089 / GB/T 97.1 |
| M36 | 37.0 | 66.0 | 5.0 | ISO 7089 / GB/T 97.1 |
