A2 Stainless Steel (A2-70 (304)) is the most common stainless grade for indoor and general outdoor fasteners. When hydraulic compression fittings are specified in this grade, the dimensions remain per DIN 2353; the material determines corrosion behavior (good general corrosion resistance) and the service temperature range (approx. -200 °C to +400 °C). Both are covered below with the size table.
Why Choose A2 Stainless Steel for Hydraulic Compression Fittings
The most common stainless grade for indoor and general outdoor fasteners. For hydraulic compression fittings, this matters when good general corrosion resistance is the primary requirement.
Mechanical & Physical Properties
| Grade designation | A2-70 (304) |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C |
| Corrosion characteristic | Good general corrosion resistance |
Galvanic & Galling Considerations
Two important notes for stainless hydraulic compression fittings: (1) stainless can gall on stainless threads under load — use a thread lubricant or anti-galling compound, especially for M6 and below; (2) when joined to aluminum or galvanized steel, stainless can drive galvanic corrosion of the less-noble metal in wet service — isolate with a coating or sleeve where appropriate.
Comparable Grades
For Hydraulic Compression Fittings, the alternative stainless grade is A4 (316). A2 (304) suits general indoor and outdoor service; A4 (316) adds molybdenum for marine and chloride environments. Where higher strength matters more than corrosion, switch to plated alloy-steel class 8.8 or 10.9.
Sizes of Hydraulic Compression Fittings Available in A2 Stainless Steel
| Tube OD (mm) | Nut length L (mm) | Nut width across flats (mm) | Tube bore (mm) | Max working pressure (bar) | Mating thread | Reference standard | Notes |
|---|---|---|---|---|---|---|---|
| 4 | 22 | 13 | 8 | 400 | M10x1 | DIN 2353 / ISO 8434-1 | Compression hydraulic fitting |
| 5 | 24 | 14 | 9 | 400 | M12x1.5 | DIN 2353 / ISO 8434-1 | Compression hydraulic fitting |
| 6 | 27 | 17 | 11 | 400 | M14x1.5 | DIN 2353 / ISO 8434-1 | Compression hydraulic fitting |
| 8 | 30 | 19 | 13 | 400 | M16x1.5 | DIN 2353 / ISO 8434-1 | Compression hydraulic fitting |
| 10 | 33 | 22 | 16 | 400 | M18x1.5 | DIN 2353 / ISO 8434-1 | Compression hydraulic fitting |
| 12 | 36 | 24 | 18 | 315 | M22x1.5 | DIN 2353 / ISO 8434-1 | Compression hydraulic fitting |
| 14 | 39 | 27 | 20 | 315 | M26x1.5 | DIN 2353 / ISO 8434-1 | Compression hydraulic fitting |
| 15 | 39 | 27 | 20 | 315 | M26x1.5 | DIN 2353 / ISO 8434-1 | Compression hydraulic fitting |
| 16 | 42 | 30 | 22 | 315 | M26x1.5 | DIN 2353 / ISO 8434-1 | Compression hydraulic fitting |
| 18 | 45 | 32 | 25 | 250 | M30x2 | DIN 2353 / ISO 8434-1 | Compression hydraulic fitting |
| 20 | 48 | 36 | 27 | 250 | M30x2 | DIN 2353 / ISO 8434-1 | Compression hydraulic fitting |
| 22 | 51 | 38 | 30 | 250 | M36x2 | DIN 2353 / ISO 8434-1 | Compression hydraulic fitting |
| 25 | 55 | 41 | 32 | 250 | M36x2 | DIN 2353 / ISO 8434-1 | Compression hydraulic fitting |
| 28 | 58 | 46 | 36 | 160 | M42x2 | DIN 2353 / ISO 8434-1 | Compression hydraulic fitting |
| 30 | 60 | 48 | 38 | 160 | M42x2 | DIN 2353 / ISO 8434-1 | Compression hydraulic fitting |
| 35 | 66 | 55 | 44 | 160 | M52x2 | DIN 2353 / ISO 8434-1 | Compression hydraulic fitting |
| 38 | 69 | 58 | 47 | 160 | M52x2 | DIN 2353 / ISO 8434-1 | Compression hydraulic fitting |
| 42 | 74 | 65 | 52 | 100 | M60x2 | DIN 2353 / ISO 8434-1 | Compression hydraulic fitting |