Self-Tapping Screws manufactured in A2 Stainless Steel (ISO 3506 group A2 (304 / 1.4301), commonly supplied A2-70) are dimensioned to DIN 7976 / ISO 1481. The sections below give the mechanical and physical properties of the grade, its behavior in corrosive and elevated-temperature service, and the full size table.
Why Choose A2 Stainless Steel for Self-Tapping Screws
The most common stainless group for indoor and general outdoor fasteners. For self-tapping screws, this matters when good general corrosion resistance is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 3506 group A2 (304 / 1.4301), commonly supplied A2-70 |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C, subject to the property class and the joint |
| Corrosion characteristic | Good general corrosion resistance |
Corrosion Behavior in Service
A2 (304) gives excellent atmospheric and most-water corrosion resistance and is the most common stainless for Self-Tapping Screws in indoor and general outdoor service. In chloride-bearing environments (marine air, road salt, swimming pools) consider stepping up to A4 (316).
Comparable Grades
For Self-Tapping Screws, the alternative stainless grade is A4 (316). A2 (304) suits general indoor and outdoor service; A4 (316) adds molybdenum for marine and chloride environments. Where higher strength matters more than corrosion, switch to plated alloy-steel class 8.8 or 10.9.
Using Stainless Fasteners in Aluminum
Stainless steel is more noble than aluminum, so in the presence of an electrolyte — rain, condensation, salt spray — the aluminum becomes the anode and corrodes at the joint. The effect is driven by the area ratio: a small stainless fastener in a large aluminum section is normally acceptable, while a large stainless fastener in thin aluminum is not. Where the joint is wet, isolate the two metals with a coated or nylon washer and a sealant, or specify an aluminum or coated fastener instead.
Sizes of Self-Tapping Screws Available in A2 Stainless Steel
| Size | Nominal diameter (mm) | Pilot hole (mm) | Pitch (mm) | Head diameter dk (mm) | Head height k (mm) | Plate thickness (mm) | Reference standard | Notes |
|---|---|---|---|---|---|---|---|---|
| ST2.2 | 2.2 | 1.7 | 0.71 | 4.2 | 1.4 | 0.5~1.0 | DIN 7976 / ISO 1481 | Cross-recess pan-head self-tapping |
| ST2.9 | 2.9 | 2.3 | 0.94 | 5.6 | 1.7 | 0.6~1.6 | DIN 7976 / ISO 1481 | Cross-recess pan-head self-tapping |
| ST3.5 | 3.5 | 2.8 | 1.27 | 6.9 | 2.1 | 0.8~2.0 | DIN 7976 / ISO 1481 | Cross-recess pan-head self-tapping |
| ST3.9 | 3.9 | 3.1 | 1.29 | 7.5 | 2.3 | 0.9~2.5 | DIN 7976 / ISO 1481 | Cross-recess pan-head self-tapping |
| ST4.2 | 4.2 | 3.4 | 1.41 | 8.2 | 2.5 | 1.0~2.5 | DIN 7976 / ISO 1481 | Cross-recess pan-head self-tapping |
| ST4.8 | 4.8 | 3.9 | 1.59 | 9.5 | 2.9 | 1.2~3.0 | DIN 7976 / ISO 1481 | Cross-recess pan-head self-tapping |
| ST5.5 | 5.5 | 4.5 | 1.81 | 10.9 | 3.3 | 1.5~3.5 | DIN 7976 / ISO 1481 | Cross-recess pan-head self-tapping |
| ST6.3 | 6.3 | 5.1 | 1.81 | 12.5 | 3.8 | 2.0~4.0 | DIN 7976 / ISO 1481 | Cross-recess pan-head self-tapping |
| ST8.0 | 8.0 | 6.7 | 2.12 | 16.0 | 4.8 | 2.5~5.0 | DIN 7976 / ISO 1481 | Cross-recess pan-head self-tapping |
| ST9.5 | 9.5 | 8.0 | 2.12 | 19.0 | 5.7 | 3.0~6.0 | DIN 7976 / ISO 1481 | Cross-recess pan-head self-tapping |
