Material specification page for slotted pan head screw in A4 Stainless Steel. Covers the grade designation (ISO 3506 group A4 (316 / 1.4401), commonly supplied A4-80), corrosion and magnetic behavior, comparable grades and their trade-offs, and the sizes available to GB/T 67 / ISO 1580.
Why Choose A4 Stainless Steel for Slotted Pan Head Screw — GB/T 67 / ISO 1580 (Series 040)
Specified for marine, coastal and chemical applications. For slotted pan head screw — gb/t 67 / iso 1580 (series 040), this matters when superior, including marine and chloride environments is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 3506 group A4 (316 / 1.4401), commonly supplied A4-80 |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C, subject to the property class and the joint |
| Corrosion characteristic | Superior, including marine and chloride environments |
Corrosion Behavior in Service
A4 (316) adds 2–3% molybdenum to the A2 (304) composition, which dramatically improves resistance to chloride-pitting corrosion. For Slotted Pan Head Screw — GB/T 67 / ISO 1580 (Series 040) in marine, coastal, swimming-pool or food-processing environments, A4 is the default selection.
Comparable Grades
For Slotted Pan Head Screw — GB/T 67 / ISO 1580 (Series 040), the alternative stainless grade is A2 (304). Choose A2 (304) for general use and A4 (316) wherever chlorides are present; the molybdenum in A4 is the whole difference. Remember that stainless is the corrosion answer, not the strength answer — for load, look at class 8.8 or 10.9 instead.
Using Stainless Fasteners in Aluminum
Expect the aluminum to corrode, not the fastener — stainless sits higher in the galvanic series, so the aluminum is the one that gives up material. A small fastener in a thick section spreads the loss over a large area and is usually fine; a large fastener in thin sheet concentrates it and is not. Keep water out of the joint, or isolate the two metals with a nylon or coated washer and a sealant.
Sizes of Slotted Pan Head Screw — GB/T 67 / ISO 1580 (Series 040) Available in A4 Stainless Steel
| Size | Pitch (mm) | Length L (mm) | Head diameter dk (mm) | Head height k (mm) | Cross recess | Reference standard |
|---|---|---|---|---|---|---|
| M3 | 0.5 | 20 | 5.6 | 1.8 | PH1 | ISO 7045 / GB/T 818 |
| M4 | 0.7 | 25 | 8.0 | 2.4 | PH2 | ISO 7045 / GB/T 818 |
| M5 | 0.8 | 30 | 9.5 | 3.0 | PH2 | ISO 7045 / GB/T 818 |
| M6 | 1.0 | 40 | 12.0 | 3.6 | PH3 | ISO 7045 / GB/T 818 |
| M8 | 1.25 | 50 | 16.0 | 4.8 | PH3 | ISO 7045 / GB/T 818 |
| M10 | 1.5 | 60 | 20.0 | 6.0 | PH4 | ISO 7045 / GB/T 818 |
Dimensions are independent of the material: every size above is available in A4 Stainless Steel.
Custom manufacturing · Made to drawing
Need this screw in a grade that is not listed?
A4 Stainless Steel is one of the grades the catalog describes. Lengths and thread lengths outside the standard table are the commonest request, followed by a drive the standard does not offer and a head marked with your own part number. Made by cold heading or warm forging.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
