Spring Lock Washer manufactured in A4 Stainless Steel (ISO 3506 group A4 (316 / 1.4401), commonly supplied A4-80) are dimensioned to GB/T 93 / DIN 127B. The sections below give the mechanical and physical properties of the grade, its behavior in corrosive and elevated-temperature service, and the full size table.
Why Choose A4 Stainless Steel for Spring Lock Washer — GB/T 93 / DIN 127B (Series 080)
Specified for marine, coastal and chemical applications. For spring lock washer — gb/t 93 / din 127b (series 080), this matters when superior, including marine and chloride environments is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 3506 group A4 (316 / 1.4401), commonly supplied A4-80 |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C, subject to the property class and the joint |
| Corrosion characteristic | Superior, including marine and chloride environments |
Corrosion Behavior in Service
A4 (316) adds 2–3% molybdenum to the A2 (304) composition, which dramatically improves resistance to chloride-pitting corrosion. For Spring Lock Washer — GB/T 93 / DIN 127B (Series 080) in marine, coastal, swimming-pool or food-processing environments, A4 is the default selection.
Comparable Grades
For Spring Lock Washer — GB/T 93 / DIN 127B (Series 080), the alternative stainless grade is A2 (304). A2 (304) suits general indoor and outdoor service; A4 (316) adds molybdenum for marine and chloride environments. Where higher strength matters more than corrosion, switch to plated alloy-steel class 8.8 or 10.9.
Using Stainless Fasteners in Aluminum
Stainless steel is more noble than aluminum, so in the presence of an electrolyte — rain, condensation, salt spray — the aluminum becomes the anode and corrodes at the joint. The effect is driven by the area ratio: a small stainless fastener in a large aluminum section is normally acceptable, while a large stainless fastener in thin aluminum is not. Where the joint is wet, isolate the two metals with a coated or nylon washer and a sealant, or specify an aluminum or coated fastener instead.
Sizes of Spring Lock Washer — GB/T 93 / DIN 127B (Series 080) Available in A4 Stainless Steel
| For bolt size | Inner diameter d1 (mm) | Outer diameter d2 (mm) | Width b (mm) | Thickness t (mm) | Reference standard |
|---|---|---|---|---|---|
| M3 | 3.1 | 6.2 | 1.0 | 0.8 | GB/T 93 / DIN 127B |
| M4 | 4.1 | 7.6 | 1.2 | 1.0 | GB/T 93 / DIN 127B |
| M5 | 5.1 | 9.2 | 1.5 | 1.2 | GB/T 93 / DIN 127B |
| M6 | 6.1 | 11.8 | 2.0 | 1.6 | GB/T 93 / DIN 127B |
| M8 | 8.1 | 14.8 | 2.5 | 2.0 | GB/T 93 / DIN 127B |
| M10 | 10.2 | 18.1 | 3.0 | 2.5 | GB/T 93 / DIN 127B |
| M12 | 12.2 | 21.1 | 3.5 | 3.0 | GB/T 93 / DIN 127B |
| M14 | 14.2 | 24.1 | 4.0 | 3.5 | GB/T 93 / DIN 127B |
| M16 | 16.2 | 27.4 | 4.5 | 4.0 | GB/T 93 / DIN 127B |
| M18 | 18.2 | 29.4 | 5.0 | 4.5 | GB/T 93 / DIN 127B |
| M20 | 20.2 | 33.6 | 5.5 | 5.0 | GB/T 93 / DIN 127B |
| M24 | 24.5 | 40.1 | 6.5 | 6.0 | GB/T 93 / DIN 127B |
| M30 | 30.5 | 50.0 | 8.0 | 7.5 | GB/T 93 / DIN 127B |
