A4 Stainless Steel Conical Spring Washers (HV) are supplied to DIN 6796. The grade provides superior, including marine and chloride environments and is largely non-magnetic; the practical service range is approx. -200 °C to +400 °C, subject to the property class and the joint. Property data, grade comparison and the full size table follow.
Why Choose A4 Stainless Steel for Conical Spring Washers (HV)
Specified for marine, coastal and chemical applications. For conical spring washers (hv), this matters when superior, including marine and chloride environments is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 3506 group A4 (316 / 1.4401), commonly supplied A4-80 |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C, subject to the property class and the joint |
| Corrosion characteristic | Superior, including marine and chloride environments |
Corrosion Behavior in Service
A4 (316) adds 2–3% molybdenum to the A2 (304) composition, which dramatically improves resistance to chloride-pitting corrosion. For Conical Spring Washers (HV) in marine, coastal, swimming-pool or food-processing environments, A4 is the default selection.
Galvanic & Galling Considerations
For stainless conical spring washers (hv) the compatibility question is galvanic rather than galling: joined to aluminum or galvanized steel in wet service, stainless drives corrosion of the less-noble metal. Isolate with a coating, sleeve or non-conductive washer where the joint sees moisture. Note also that stainless is softer than hardened carbon steel, so where the part carries a wear or shear duty, check the load against the grade before substituting.
Using Stainless Fasteners in Aluminum
The galvanic couple here runs the wrong way: aluminum is the less noble metal, so it corrodes and the fastener does not. What governs the rate is the ratio of areas — a large anode and a small cathode is a tolerable combination, the reverse concentrates the attack into thin material around the hole. An isolating washer plus sealant breaks the circuit; where that is impractical, match the fastener to the substrate.
Sizes of Conical Spring Washers (HV) Available in A4 Stainless Steel
| Size | Inner diameter d1 (mm) | Outer diameter d2 (mm) | Thickness s (mm) | Height h max (mm) | Height h min (mm) | Reference standard |
|---|---|---|---|---|---|---|
| M2 | 2.2 | 5 | 0.4 | 0.6 | 0.5 | DIN 6796 |
| M2.5 | 2.7 | 6 | 0.5 | 0.72 | 0.61 | DIN 6796 |
| M3 | 3.2 | 7 | 0.6 | 0.85 | 0.72 | DIN 6796 |
| M3.5 | 3.7 | 8 | 0.8 | 1.06 | 0.92 | DIN 6796 |
| M4 | 4.3 | 9 | 1 | 1.3 | 1.12 | DIN 6796 |
| M5 | 5.3 | 11 | 1.2 | 1.55 | 1.35 | DIN 6796 |
| M6 | 6.4 | 14 | 1.5 | 2 | 1.7 | DIN 6796 |
| M7 | 7.4 | 17 | 1.75 | 2.3 | 2 | DIN 6796 |
| M8 | 8.4 | 18 | 2 | 2.6 | 2.4 | DIN 6796 |
| M10 | 10.5 | 23 | 2.5 | 3.2 | 2.8 | DIN 6796 |
| M12 | 13 | 29 | 3 | 3.95 | 3.43 | DIN 6796 |
| M14 | 15 | 35 | 3.5 | 4.65 | 4.04 | DIN 6796 |
| M16 | 17 | 39 | 4 | 5.25 | 4.58 | DIN 6796 |
| M18 | 19 | 42 | 4.5 | 5.6 | 5.08 | DIN 6796 |
| M20 | 21 | 45 | 5 | 6.4 | 5.6 | DIN 6796 |
| M22 | 23 | 49 | 5.5 | 7.05 | 6.15 | DIN 6796 |
| M24 | 25 | 56 | 6 | 7.75 | 6.77 | DIN 6796 |
| M27 | 28 | 60 | 6.5 | 8.35 | 7.3 | DIN 6796 |
| M30 | 31 | 70 | 7 | 9.2 | 8 | DIN 6796 |
Dimensions are independent of the material: every size above is available in A4 Stainless Steel.
Custom manufacturing · Made to drawing
Need this washer in a grade that is not listed?
A4 Stainless Steel is one of the grades the catalog describes. Bore and outside diameter are set by the joint rather than by the bolt, which is why an off-table size is so often the right answer. Made by stamping or punching.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
