Screws · Trade series (confirmat furniture screws)
Property Class 12.9 Steel Confirmat Furniture Screws
Mechanical properties, corrosion behaviour and the full dimensional range for this grade.
Property Class 12.9 Steel Confirmat Furniture Screws are supplied to ISO 898-1 property class 12.9. Corrosion behaviour is requires plating or black-oxide protection, the material is magnetic, and the usable service range is commonly limited to approx. +300 °C; confirm against the coating and the load. In practice this grade is the highest common strength class, for high-load machine assembly.
Grade
ISO 898-1 property class 12.9
Corrosion resistance
Requires plating or black-oxide protection
Magnetic response
Magnetic
Service temperature
commonly limited to approx. +300 °C; confirm against the coating and the load
Property values are typical for the grade. Certified mechanical test data is available on request for production orders.
Hidden Deck Fasteners Sourcing: Manufacturing, Types & Material Compatibility
Confirmat Furniture Screws manufactured in Property Class 12.9 Steel (ISO 898-1 property class 12.9) are dimensioned to Trade series (confirmat furniture screws). The sections below give the mechanical and physical properties of the grade, its behavior in corrosive and elevated-temperature service, and the full size table.
Why Choose Property Class 12.9 Steel for Confirmat Furniture Screws
The highest common strength class, for high-load machine assembly. For confirmat furniture screws, this matters when requires plating or black-oxide protection is the primary requirement.
Mechanical & Physical Properties
Grade designation
ISO 898-1 property class 12.9
Magnetic response
Magnetic
Service temperature
commonly limited to approx. +300 °C; confirm against the coating and the load
Corrosion characteristic
Requires plating or black-oxide protection
Corrosion Behavior in Service
Carbon and alloy steel confirmat furniture screws require a coating for corrosion protection. Zinc plating (with or without passivation) is the most common; hot-dip galvanizing is used for outdoor structural service; black-oxide is mainly a tarnish-prevention finish for tool-room use.
Comparable Grades
For Confirmat Furniture Screws, class 8.8 is the comparable strength step. Move up when the joint preload approaches the proof load of the current class; move down when the joint is over-specified. For corrosion-critical service, switch to stainless A2 or A4.
Sizes of Confirmat Furniture Screws Available in Property Class 12.9 Steel
Customize the parameters below — every spec field is editable, and the drawing redraws to match the values you choose. Changing the size will snap the other fields to that size's standard values; you can then override any individual value.
Sends the selected values to the quote form below.
Request a Quote
The form below follows the current technical drawing configuration. Change the drawing values above and the request details update automatically.
Dimensions & Specifications (Trade series (confirmat furniture screws))
Flat-pack manufacturingHex or Pozidriv options suit production and field assembly.
Furniture repair30–70 mm lengths cover common panel thickness combinations.
Particleboard furnitureConfirmat screws clamp board joints with a large-diameter body.
Energy & infrastructureTower, pipework, switchgear and plant fixings specified for long service life and inspectable joints.
Maintenance & MROStocked replacements matched to an existing property class, thread and finish.
Typical applications
matching the 5 or 7 mm body to the pilot hole
selecting 30–70 mm length from the panel stack
using the supplied hex or Pozidriv drive
joining particleboard or MDF with a prepared pilot hole
bolting brackets, motors and gearboxes to a frame
assemblies that are dismantled for service and re-torqued
Service conditions to specify against
Marine and coastal
Available in A4 (316) stainless for chloride exposure — coastal structures, pool halls, water treatment and deck hardware, where A2 will eventually pit.
High load
Supplied in ISO 898-1 property classes, so the joint can be designed to a stated proof load and tightened to a calculated torque rather than by feel.
Torque and preload
The joint is designed around bolt tension, so lubrication, coating and the friction coefficient all change the torque figure — state them together.
Where to use something else
Do not use a confirmat without the specified pilot hole; the large body can split the board.
Do not use a machine thread into unthreaded sheet or timber; use a tapping screw, rivet nut or insert made for that parent material.
This part is cold-formed, threaded, heat-treated and finished in-house. The stages below are where its class and finish are actually decided.
01
Cold heading
Wire rod is drawn to size and cold-formed into blanks. Forming rather than cutting keeps the grain flow continuous around the head, which is where a bolt is most likely to fail.
Head dimensions and under-head radius checked at set-up and per shift.
02
Thread rolling
Threads are rolled between hardened dies rather than cut. Rolled threads are stronger in fatigue than cut threads and hold pitch and flank angle far more consistently across a batch.
Go / no-go ring gauges to ISO 965 tolerance class 6g.
03
Heat treatment
Quench-and-temper brings carbon and alloy steel to the property class ordered — 8.8, 10.9 or 12.9 — with the furnace charge tracked so a finished lot can be traced back to it.
Core hardness and tensile tested per lot to ISO 898-1.
04
Surface treatment
Zinc, zinc-nickel, hot-dip galvanizing, black oxide, phosphate and Dacromet, selected against the service environment rather than against the price list.
Coating thickness and neutral salt spray hours to ISO 9227.
Frequently Asked Questions
Is Property Class 12.9 Steel prone to hydrogen embrittlement?
Class 10.9 and above can be susceptible to hydrogen embrittlement when electroplated. Specify post-plating baking, or use mechanical-zinc / zinc-flake finishes which avoid the cathodic plating step.
Which finish is best for outdoor Confirmat Furniture Screws?
For outdoor service in steel, hot-dip galvanizing gives the longest life; zinc-flake (Geomet/Delta-Tone family) gives a thinner film with excellent salt-spray performance; standard zinc plating is the lowest-cost option for general indoor / shielded outdoor use.
What's the service temperature limit for Property Class 12.9 Steel?
The practical service range is commonly limited to approx. +300 °C; confirm against the coating and the load.
Can Property Class 12.9 Steel replace stainless steel structurally?
No — stainless A2/A4 cannot match class 10.9 / 12.9 strength. Stainless is selected for corrosion, not raw strength.
How do I request a quotation?
Use the technical drawing on this page to pick the exact configuration, then submit it with the quote form. We respond within one business day.
This website uses only necessary and functional cookies to operate, secure, and improve basic website performance.
We do not use advertising cookies, Google Analytics, or cross-site tracking technologies.
Privacy Policy
