---
title: "M1.6 JIS Cross-Recess Micro Screws Dimensions"
description: "M1.6 JIS Cross-Recess Micro Screws: head diameter 2.3 mm, head height 0.5 mm, coarse thread pitch 0.35 mm. Tightening torque 0.2 Nm at class 8.8."
url: https://engineeringhardware.com/guide/size/m1-6-jis-cross-recess-micro-screws/
source: Engineering Hardware & Fasteners
---

# M1.6 JIS Cross-Recess Micro Screws Dimensions

Screws · Trade series (JIS cross-recess micro screws)

Controlling dimensions to Trade series (JIS cross-recess micro screws), with clearance hole and tapping drill, spanner or drive size and tightening torque.

M1.6 JIS Cross-Recess Micro Screws dimensions to Trade series (JIS cross-recess micro screws): head diameter 2.3 mm, head height 0.5 mm, coarse thread pitch 0.35 mm, clearance hole (ISO 273 medium) 1.8 mm. Tighten to approximately 0.2 Nm at property class 8.8 in a dry, as-supplied condition.

- **Head diameter:** 2.3 mm
- **Head height:** 0.5 mm
- **Coarse thread pitch:** 0.35 mm
- **Clearance hole (ISO 273 medium):** 1.8 mm
- **Tightening torque (class 8.8):** 0.2 Nm

Figures are nominal values from the governing standard. Confirm against the tolerance class for your application before machining or ordering.

![M1.6 JIS Cross-Recess Micro Screws Dimensions reference image](https://engineeringhardware.com/wp-content/uploads/2026/09/310Micro-JCIS-Micro-Screws.webp)

M1.6 is one of the standard coarse-thread sizes for jis cross-recess micro screws under Trade series (JIS cross-recess micro screws). The sections below reproduce the dimensional row, list the matching tools and hole sizes, and summarize where this size is normally specified.

## M1.6 Dimensional Row (Trade series (JIS cross-recess micro screws))

| Thread size | Head diameter (mm) | Head height (mm) | Length options (mm) | Drive | Finish |
| --- | --- | --- | --- | --- | --- |
| M1.6 | 2.3 | 0.50 | 1.5~12 | JCIS/JIS #0–1 | trivalent zinc-plated steel |

## Spanner & Drive for M1.6 JIS Cross-Recess Micro Screws

Drive geometry for M1.6 JIS Cross-Recess Micro Screws is given by the row above; match the tool to the listed values.

## Hole Sizes for M1.6

| Coarse-thread pitch (ISO 724) | 0.35 mm |
| --- | --- |
| Through-hole / clearance (ISO 273 medium) | 1.8 mm |
| Tapping drill, coarse thread | 1.25 mm |

## Tightening Torque for M1.6

| Class 8.8 (dry, ~µ 0.125) | ≈ 0.2 Nm |
| --- | --- |
| Class 10.9 (dry, ~µ 0.125) | ≈ Nm |
| Class 12.9 (dry, ~µ 0.125) | ≈ 0.3 Nm |

Indicative dry-joint values. Lubrication can lower the required torque by 15–25%. Always confirm against the joint design, especially when going up a strength class.

## Proof Load & Strength for M1.6

| Tensile stress area As (ISO 724) | 1.3 mm² |
| --- | --- |
| Proof load, class 8.8 | 0.7 kN |
| Proof load, class 12.9 | 1.2 kN |
| Min. ultimate tensile load, class 8.8 | 1 kN |

Proof load = tensile stress area × the proof stress Sp of the class, per ISO 898-1 — Sp is a lower figure than the yield stress Rp0.2 and the two are not interchangeable. The stress area is computed from this size's own diameter and pitch, so a fine-pitch designation gives the fine-pitch figure. Design the joint so the working preload stays below the proof load of the class selected.

## M1.6 JIS Cross-Recess Micro Screws Weight

A steel M1.6 jis cross-recess micro screws at the listed 1.5 mm length weighs approximately 0.0 g each — about 0.0 kg per 1,000 pieces. Stainless A2/A4 weighs roughly the same (density 7.9–8.0 g/cm³).

Actual weight varies slightly with head form, thread and finish; use this figure for freight estimation only.

## Installation Tips for M1.6 JIS Cross-Recess Micro Screws

- At M1.6 the joint is sensitive to over-torque — use a torque-limiting driver and check the head doesn't bury into a softer counterpart.

## Mating Parts for M1.6

For M1.6, pair with a M1.6 hex nut (ISO 4032 / DIN 934) and, where used, a M1.6 flat washer (ISO 7089 / DIN 125A) under the head and under the nut.

Custom manufacturing · Made to drawing

## Need JIS cross-recess micro screws in a size this table does not list?

This page covers M1.6 JIS cross-recess micro screws. Thread size and pitch, length, property class, drive form, head geometry and head marking are all specifiable — the standard part is where it starts, not where it stops. Made by cold heading or warm forging.

Minimum order from 2,000 pieces; samples within 7 days of drawing approval.

[Custom screw manufacturing](https://engineeringhardware.com/custom/screws/)[Send a drawing](https://engineeringhardware.com/custom/screws/#rfq)

## Technical Drawing

Dimensioned line drawing of M1.6 JIS Cross-Recess Micro Screws to Trade series (JIS cross-recess micro screws). Side view and top view, drawn to the dimensions in the table below and redrawn for any size selected.

- **Head diameter (mm):** 2.3
- **Head height (mm):** 0.50
- **Length options (mm):** 1.5~12
- **Drive:** JCIS/JIS #0–1
- **Finish:** trivalent zinc-plated steel

## Dimensions & Specifications (Trade series (JIS cross-recess micro screws))

| Thread size | Head diameter (mm) | Head height (mm) | Length options (mm) | Drive | Finish |
| --- | --- | --- | --- | --- | --- |
| M1.0 | 1.8 | 0.50 | 2.5 | JCIS/JIS #0–1 | trivalent zinc-plated steel |
| M1.2 | 1.8 | 0.50 | 2~5 | JCIS/JIS #0–1 | trivalent zinc-plated steel |
| M1.4 | 2.0 | 0.50 | 1.4~12 | JCIS/JIS #0–1 | trivalent zinc-plated steel |
| M1.6 | 2.3 | 0.50 | 1.5~12 | JCIS/JIS #0–1 | trivalent zinc-plated steel |
| M1.7 | 2.5 | 0.50 | 1.5~14 | JCIS/JIS #0–1 | trivalent zinc-plated steel |

Product catalog

## Related Micro & Miniature Screws products

[![Creditsolid Stainless Steel Self-Drilling Screw Fastener, Hexagon Washer Head Metal Roof Screw](https://img.engineeringhardware.com/Creditsolid-Stainless-Steel-Self-Drilling-Screw-Fastener-Hexagon-Washer-Head-Metal-Roof-Screw.webp)](https://engineeringhardware.com/product/creditsolid-stainless-steel-self-drilling-screw-fastener-hexagon-washer-head-metal/)

Self-Drilling & Tek Screws

### [Creditsolid Stainless Steel Self-Drilling Screw Fastener, Hexagon Washer Head Metal Roof Screw](https://engineeringhardware.com/product/creditsolid-stainless-steel-self-drilling-screw-fastener-hexagon-washer-head-metal/)

Hexagon Head · DIN, GB, ANSI, BSW, JIS, GOST

**US$0.012 – 0.036**MOQ 10,000 pieces

[![Stainless Steel 316 A4 Pan Hex Flat Wafer Head Self Drilling Screw](https://img.engineeringhardware.com/Stainless-Steel-316-A4-Pan-Hex-Flat-Wafer-Head-Self-Drilling-Screw.webp)](https://engineeringhardware.com/product/stainless-steel-316-a4-pan-hex-flat-wafer-head-self-drilling-screw/)

Self-Drilling & Tek Screws

### [Stainless Steel 316 A4 Pan Hex Flat Wafer Head Self Drilling Screw](https://engineeringhardware.com/product/stainless-steel-316-a4-pan-hex-flat-wafer-head-self-drilling-screw/)

Wafer · DIN, GB, ANSI, BSW, JIS, GOST

**US$0.012 – 0.12**MOQ 100 pieces

[![Versatile DIN7504K Self-Drill Screw with Washer – Customizable Colors](https://img.engineeringhardware.com/Versatile-DIN7504K-Self-Drill-Screw-with-Washer-Customizable-Colors.webp)](https://engineeringhardware.com/product/versatile-din7504k-self-drill-screw-with-washer-customizable-colors/)

Self-Drilling & Tek Screws

### [Versatile DIN7504K Self-Drill Screw with Washer – Customizable Colors](https://engineeringhardware.com/product/versatile-din7504k-self-drill-screw-with-washer-customizable-colors/)

Countersunk Head · DIN, GB, ANSI, BSW, JIS, GOST

**US$0.018 – 0.0408**MOQ 1,000 pieces

[![Bulge Head Self Drilling Screws for Metal White Blue Zinc Plated Skipproof](https://img.engineeringhardware.com/Bulge-Head-Self-Drilling-Screws-for-Metal-White-Blue-Zinc-Plated-Skipproof.webp)](https://engineeringhardware.com/product/bulge-head-self-drilling-screws-for-metal-white-blue-zinc-plated-skipproof/)

Self-Drilling & Tek Screws

### [Bulge Head Self Drilling Screws for Metal White Blue Zinc Plated Skipproof](https://engineeringhardware.com/product/bulge-head-self-drilling-screws-for-metal-white-blue-zinc-plated-skipproof/)

Countersunk Head · DIN, GB, ANSI, BSW, JIS, GOST

**US$0.0012 – 1.20**MOQ 1,000 pieces

[![Point 5 Pu Roof Long Hexagon Washer Head Self-drilling Screw For Sandwich Panel](https://img.engineeringhardware.com/Point-5-Pu-Roof-Long-Hexagon-Washer-Head-Self-drilling-Screw-For-Sandwich-Panel.webp)](https://engineeringhardware.com/product/point-5-pu-roof-long-hexagon-washer-head-self-drilling-screw-for-sandwich-panel/)

Self-Drilling & Tek Screws

### [Point 5 Pu Roof Long Hexagon Washer Head Self-drilling Screw For Sandwich Panel](https://engineeringhardware.com/product/point-5-pu-roof-long-hexagon-washer-head-self-drilling-screw-for-sandwich-panel/)

International/Customized · Carbon Steel

**US$0.072 – 1.42**MOQ 20,000 pieces

[![Metal Tek Screws Modified Truss Head Self Drilling Screws](https://img.engineeringhardware.com/Metal-Tek-Screws-Modified-Truss-Head-Self-Drilling-Screws.webp)](https://engineeringhardware.com/product/metal-tek-screws-modified-truss-head-self-drilling-screws/)

Self-Drilling & Tek Screws

### [Metal Tek Screws Modified Truss Head Self Drilling Screws](https://engineeringhardware.com/product/metal-tek-screws-modified-truss-head-self-drilling-screws/)

Hexagon Head · DIN, GB, ANSI, BSW, JIS, GOST

**US$0.012 – 24.00**MOQ 500 pieces

[View all Self-Drilling & Tek Screws →](https://engineeringhardware.com/fastener-products/screws/self-drilling-tek-screws/) [Full product catalog](https://engineeringhardware.com/products/)

## Materials & Grades

Select a material class to see the grades we supply it in. Each designation is listed with its ISO/EN, AISI/SAE, JIS and GB equivalents.

Stainless Steel38 Carbon Steel66 Alloy Steel41 Bearing Steel5 Spring Steel25 Aluminum and Aluminum Alloys21 Brass17 Bronze11 Copper8 Titanium and Titanium Alloys18 Nickel and Nickel Alloys22 Iron-Nickel and High-Temperature Alloys10 Tool Steel and Specialty Hardened Steel9 Structural and Construction Steel9

### Stainless Steel

#### Austenitic Stainless Steel

- A1 AISI 303 · SAE 303 · SUS303 · EN 1.4305 · X8CrNiS18-9
- A2 AISI 304 · SAE 304 · SUS304 · EN 1.4301 · X5CrNi18-10 · 06Cr19Ni10
- 304L AISI 304L · SUS304L · EN 1.4307 · X2CrNi18-9 · 022Cr19Ni10
- 302 AISI 302 · SUS302 · EN 1.4310
- 305 AISI 305 · SUS305 · EN 1.4303
- A4 AISI 316 · SAE 316 · SUS316 · EN 1.4401 · X5CrNiMo17-12-2 · 06Cr17Ni12Mo2
- 316L AISI 316L · SUS316L · EN 1.4404 · X2CrNiMo17-12-2 · 022Cr17Ni12Mo2
- 321 AISI 321 · SUS321 · EN 1.4541 · X6CrNiTi18-10
- 310 / 310S AISI 310 · AISI 310S · SUS310S · EN 1.4845
- 302HQ AISI 302HQ
- A3
- A5
- 347 AISI 347 · SUS347 · EN 1.4550 · X6CrNiNb18-10
- 309 / 309S AISI 309 · AISI 309S · SUS309S

#### Martensitic Stainless Steel

- AISI 410 SUS410 · EN 1.4006 · X12Cr13 · 12Cr13
- AISI 420 SUS420J1 · SUS420J2 · EN 1.4021 · EN 1.4028 · 20Cr13 · 30Cr13
- AISI 431 SUS431 · EN 1.4057 · X17CrNi16-2
- C1
- C3
- C4
- AISI 440A
- AISI 440B
- AISI 440C SUS440C · EN 1.4125

#### Ferritic Stainless Steel

- AISI 430 SUS430 · EN 1.4016 · X6Cr17 · 10Cr17
- F1
- AISI 434
- AISI 444

#### Precipitation-Hardening Stainless Steel

- 17-4 PH AISI 630 · UNS S17400 · SUS630 · EN 1.4542 · X5CrNiCuNb16-4
- 15-5 PH UNS S15500
- 17-7 PH UNS S17700

#### Duplex and Super Duplex Stainless Steel

- Duplex 2205 UNS S31803 · UNS S32205 · EN 1.4462
- Super Duplex 2507 UNS S32750 · EN 1.4410
- D2
- D4
- D6
- D8
- Lean Duplex 2101 UNS S32101
- Super Duplex S32760 UNS S32760 · EN 1.4501

### Carbon Steel

#### Low-Carbon Steel

- SAE 1006
- SAE 1008
- SAE 1010
- SAE 1018
- SAE 1020
- Q195
- Q235
- SAE 1012
- SAE 1015
- Q215
- ML08
- ML08Al
- ML10
- ML15
- ML20
- SWRCH6A
- SWRCH8A
- SWRCH10A
- SWRCH12A
- SWRCH15A
- SWRCH18A

#### Medium-Carbon Steel

- SAE 1035
- SAE 1045
- S45C
- C45
- SAE 1030
- SAE 1040
- SAE 1050
- 30
- 35
- 40
- 45
- 50
- S35C
- S40C
- S50C
- C35
- C40

#### High-Carbon Steel

- SAE 1060
- SAE 1070
- 65Mn
- SAE 1065
- SAE 1075
- SAE 1080
- SAE 1085
- SAE 1090
- SAE 1095
- 60
- 65
- 70
- 75
- 80
- 85

#### Cold-Heading Steel

- SWRCH22A
- 10B21
- SWRCH22K
- SWRCH25K
- SWRCH30K
- SWRCH35K
- SWRCH40K
- ML20Mn
- ML25
- ML30
- ML35
- ML40
- 15B25

### Alloy Steel

#### Chromium Steel

- 40Cr
- 45Cr
- AISI 5140
- SAE 5140
- AISI 5120
- SAE 5120
- SCr420
- SCr440

#### Chromium-Molybdenum Steel

- 35CrMo
- 42CrMo
- AISI 4140
- SCM435
- SCM440
- 42CrMo4
- 30CrMo
- AISI 4130
- SAE 4130
- SAE 4140
- AISI 4142
- AISI 4145
- SCM415
- SCM420
- SCM445
- EN 1.7220
- EN 1.7225
- 25CrMo4
- 34CrMo4

#### Nickel-Chromium-Molybdenum Steel

- AISI 4340
- SAE 4340
- 40CrNiMo
- SNCM439
- EN 1.6511
- 36CrNiMo4

#### Boron Alloy Steel

- 10B22
- 10B21
- 15B21
- 15B25
- 20MnTiB
- 20Mn2B
- 35VB
- 40MnB

### Bearing Steel

#### Bearing Steel

- GCr15
- AISI 52100 SAE 52100 · UNS G52986
- SUJ2
- 100Cr6 EN 1.3505
- GCr15SiMn

### Spring Steel

#### Carbon Spring Steel

- SAE 1065
- SAE 1070
- SAE 1075
- SAE 1080
- SAE 1095
- 65
- 70
- 75
- 80
- 65Mn

#### Silicon-Manganese Spring Steel

- 60Si2Mn
- 60Si2MnA
- SUP6
- SUP7

#### Chromium-Vanadium Spring Steel

- 50CrVA
- SAE 6150
- AISI 6150
- SUP10

#### Stainless Spring Steel

- AISI 301
- SUS301
- EN 1.4310
- AISI 302
- AISI 304
- AISI 316
- 17-7 PH

### Aluminum and Aluminum Alloys

#### Commercially Pure Aluminum

- 1050
- 1060
- 1070
- 1100

#### 2xxx Series Aluminum

- 2024
- 2011
- 2014
- 2017

#### 5xxx Series Aluminum

- 5052
- 5083
- 5754

#### 6xxx Series Aluminum

- 6061
- 6061-T6
- 6063
- 6082
- 6082-T6

#### 7xxx Series Aluminum

- 7075
- 7075-T6
- 7005
- 7050
- 7075-T73

### Brass

#### Free-Cutting Brass

- C36000
- H62
- HPb59-1
- C3601
- C3602
- C3604
- CuZn36Pb3
- CuZn39Pb3
- EN CW614N
- EN CW617N
- H65

#### Lead-Free Brass

- C69300
- C27450
- CW510L
- CW511L

#### Naval Brass

- C46400
- CuZn39Sn1

### Bronze

#### Silicon Bronze

- C65500
- C65100
- C65600

#### Phosphor Bronze

- C51000
- C52100
- CuSn6
- CuSn8

#### Aluminum Bronze

- C95400
- C95500
- C63000
- CuAl10Ni5Fe4

### Copper

#### Copper

- C11000
- T2
- C10100
- C10200
- C12200
- T1
- TU1
- TU2

### Titanium and Titanium Alloys

#### Commercially Pure Titanium

- Grade 2
- Grade 1
- Grade 3
- Grade 4
- TA1
- TA2
- TA3

#### Alpha-Beta Titanium Alloys

- Grade 5
- Ti-6Al-4V
- TC4
- UNS R56400

#### Low-Interstitial Grade

- Grade 23
- Ti-6Al-4V ELI
- UNS R56407

#### Other Titanium Fastener Alloys

- Ti-6Al-6V-2Sn
- Ti-6Al-2Sn-4Zr-2Mo
- Beta-C titanium
- Ti-10V-2Fe-3Al

### Nickel and Nickel Alloys

#### Commercially Pure Nickel

- Nickel 200
- UNS N02200
- Nickel 201
- UNS N02201

#### Inconel Alloys

- Inconel 625 UNS N06625
- Inconel 718 UNS N07718
- Inconel 600 UNS N06600
- Inconel 601 UNS N06601
- Inconel 686 UNS N06686
- Inconel X-750 UNS N07750

#### Monel Alloys

- Monel 400 UNS N04400
- Monel K-500 UNS N05500

#### Hastelloy Alloys

- Hastelloy C-276 UNS N10276
- Hastelloy C-22 UNS N06022
- Hastelloy B-2 UNS N10665
- Hastelloy B-3 UNS N10675
- Hastelloy X UNS N06002

#### Other Nickel Alloys

- Alloy 20 UNS N08020
- Alloy 625
- Alloy 718
- Alloy 825 UNS N08825
- Alloy 925 UNS N09925

### Iron-Nickel and High-Temperature Alloys

#### A286

- A-286
- UNS S66286
- EN 1.4980

#### Invar

- Invar 36
- Alloy 36
- UNS K93600
- FeNi36

#### Alloy 42

- Alloy 42
- UNS K94100
- FeNi42

### Tool Steel and Specialty Hardened Steel

#### Tool Steel and Specialty Hardened Steel

- AISI D2
- AISI H13
- SKD11
- Cr12MoV
- AISI O1
- AISI A2
- AISI S7
- SKD61
- 9CrSi

### Structural and Construction Steel

#### Structural and Construction Steel

- ASTM A36
- Q235B
- Q355B
- S355JR
- Q235C
- Q355C
- S235JR
- S275JR
- S355J2

## Applications & Industries for M1.6 JIS Cross-Recess Micro Screws

Where JIS Cross-Recess Micro Screws are used, and what decides the specification in each case. Stocked from M1.0 to M1.7.

### Industries that specify JIS Cross-Recess Micro Screws

- **Consumer electronics:** JIS cross recesses suit compact assemblies designed around Japanese service tooling.
- **Camera equipment:** Short micro lengths secure covers and internal brackets.
- **Instrument repair:** Trivalent zinc finishes support small replacement sets.
- **Precision production:** Head height and length are selected for a confined enclosure.
- **Maintenance & MRO:** Stocked replacements matched to an existing property class, thread and finish.
- **Food, pharma & cleanroom:** Stainless assemblies that are washed down, where the finish matters as much as the strength.

### Typical applications

- servicing a JCIS/JIS cross recess with the correct driver
- choosing the short length for the actual stack
- matching the small head to the surrounding component clearance
- keeping the trivalent finish consistent with the housing
- clamping two machined faces to a calculated preload
- bolting brackets, motors and gearboxes to a frame

### Service conditions to specify against

- **Marine and coastal:** Available in A4 (316) stainless for chloride exposure — coastal structures, pool halls, water treatment and deck hardware, where A2 will eventually pit.
- **High load:** Supplied in ISO 898-1 property classes, so the joint can be designed to a stated proof load and tightened to a calculated torque rather than by feel.
- **Torque and preload:** The joint is designed around bolt tension, so lubrication, coating and the friction coefficient all change the torque figure — state them together.

### Where to use something else

- Do not treat a JCIS recess as an ordinary Phillips drive; the driver fit controls whether the small head survives service.
- Do not use a machine thread into unthreaded sheet or timber; use a tapping screw, rivet nut or insert made for that parent material.

[Full application guide: where JIS Cross-Recess Micro Screws are used, how to specify them, and the cases they are wrong for](https://engineeringhardware.com/applications/jis-cross-recess-micro-screws/)

Inside the plant

## Manufactured in our own plant

This part is cold-formed, threaded, heat-treated and finished in-house. The stages below are where its class and finish are actually decided.

1. ![Wire rod feeding into a cold heading machine](https://engineeringhardware.com/wp-content/uploads/2026/08/09-wire-rod-feed-cold-heading-machine.webp) 01 **Cold heading** Wire rod is drawn to size and cold-formed into blanks. Forming rather than cutting keeps the grain flow continuous around the head, which is where a bolt is most likely to fail. Head dimensions and under-head radius checked at set-up and per shift.
2. ![Thread rolling machine producing bolt threads](https://engineeringhardware.com/wp-content/uploads/2026/08/03-thread-rolling-machine-bolt-production.webp) 02 **Thread rolling** Threads are rolled between hardened dies rather than cut. Rolled threads are stronger in fatigue than cut threads and hold pitch and flank angle far more consistently across a batch. Go / no-go ring gauges to ISO 965 tolerance class 6g.
3. ![Baskets of bolts staged for heat treatment](https://engineeringhardware.com/wp-content/uploads/2026/08/05-heat-treatment-baskets-black-bolts.webp) 03 **Heat treatment** Quench-and-temper brings carbon and alloy steel to the property class ordered — 8.8, 10.9 or 12.9 — with the furnace charge tracked so a finished lot can be traced back to it. Core hardness and tensile tested per lot to ISO 898-1.
4. ![Zinc plated bolts in a treatment basket](https://engineeringhardware.com/wp-content/uploads/2026/08/23-zinc-plated-bolts-treatment-basket.webp) 04 **Surface treatment** Zinc, zinc-nickel, hot-dip galvanizing, black oxide, phosphate and Dacromet, selected against the service environment rather than against the price list. Coating thickness and neutral salt spray hours to ISO 9227.

## Frequently Asked Questions

### What is the coarse-thread pitch of M1.6 for JIS Cross-Recess Micro Screws?

For M1.6 the standard coarse pitch is 0.35 mm — this is the value used for JIS Cross-Recess Micro Screws.

### What torque do M1.6 class 8.8 JIS Cross-Recess Micro Screws take?

A dry M1.6 class 8.8 joint takes about 0.2 Nm (≈ Nm for 10.9, ≈ 0.3 Nm for 12.9). Confirm against your joint design; lubrication reduces these values.

### What clearance and tapping drill suit M1.6?

Use a 1.8 mm clearance hole (ISO 273 medium) for through-fixing, or a 1.25 mm tapping drill for a coarse M1.6 thread.

### Is M1.6 JIS Cross-Recess Micro Screws suitable for electronics and small mechanisms?

M1.6 JIS Cross-Recess Micro Screws is in the micro range and is widely used in electronics, instrument enclosures and small precision mechanisms. Watch the over-torque margin — micro joints strip easily.

### How do I request a quotation?

Use the technical drawing on this page to pick the exact configuration, then submit it with the quote form. We respond within one business day.

## Related Pages

[View the full JIS Cross-Recess Micro Screws page](https://engineeringhardware.com/fastener/jis-cross-recess-micro-screws/)
