---
title: "M2.5 Self-Clinching Threaded Studs and Pins Dimensions"
description: "M2.5 Self-Clinching Threaded Studs and Pins: nut height 1 mm, coarse thread pitch 0.45 mm. Tightening torque 0.7 Nm at class 8.8."
url: https://engineeringhardware.com/guide/size/m2-5-self-clinching-threaded-studs-and-pins/
source: Engineering Hardware & Fasteners
---

# M2.5 Self-Clinching Threaded Studs and Pins Dimensions

Nuts · Trade series (self-clinching studs and pins)

Controlling dimensions to Trade series (self-clinching studs and pins), with spanner or drive size and tightening torque.

M2.5 Self-Clinching Threaded Studs and Pins dimensions to Trade series (self-clinching studs and pins): nut height 1 mm, coarse thread pitch 0.45 mm. Tighten to approximately 0.7 Nm at property class 8.8 in a dry, as-supplied condition.

- **Nut height:** 1 mm
- **Coarse thread pitch:** 0.45 mm
- **Tightening torque (class 8.8):** 0.7 Nm

Figures are nominal values from the governing standard. Confirm against the tolerance class for your application before machining or ordering.

![M2.5 Self-Clinching Threaded Studs and Pins Dimensions reference image](https://engineeringhardware.com/wp-content/uploads/2026/09/PEM-Self-Clinching-Threaded-Studs-and-Pins.webp)

M2.5 Self-Clinching Threaded Studs and Pins are manufactured to Trade series (self-clinching studs and pins). This page lists the controlling dimensions for the M2.5 size together with the drive and the installation notes for this type.

Values are taken from the governing standard rather than from a general machine-thread table, because this type is not selected on one.

## M2.5 Dimensional Row (Trade series (self-clinching studs and pins))

| Thread size | Length options (mm) | Head form | Material options | Example installation hole (mm) | Example sheet thickness (mm) | Example pull-through (N) |
| --- | --- | --- | --- | --- | --- | --- |
| M2.5 | 6 / 8 / 12 / 18 | flush-head stud | steel / stainless steel / aluminum | 2.5 | 1.0~1.95 | 2600 at 1.6 mm aluminum; 2800 at 1.5 mm steel |

## Spanner & Drive for M2.5 Self-Clinching Threaded Studs and Pins

Drive geometry for M2.5 Self-Clinching Threaded Studs and Pins is given by the row above; match the tool to the listed values.

## Tightening Torque for M2.5

| Class 8.8 (dry, ~µ 0.125) | ≈ 0.7 Nm |
| --- | --- |
| Class 10.9 (dry, ~µ 0.125) | ≈ Nm |
| Class 12.9 (dry, ~µ 0.125) | ≈ 1.2 Nm |

Indicative dry-joint values. Lubrication can lower the required torque by 15–25%. Always confirm against the joint design, especially when going up a strength class.

## Proof Load & Strength for M2.5

Nuts are graded to ISO 898-2 by the proof load the nut itself will hold (classes 04, 05, 5, 6, 8, 10 and 12), not by the 8.8 / 10.9 / 12.9 scale used for bolts. A class-8 nut is the correct mate for a class-8.8 bolt, and the joint is designed on the bolt, so no bolt-tension figure is quoted here.

## Installation Tips for M2.5 Self-Clinching Threaded Studs and Pins

- At M2.5 the joint is sensitive to over-torque — use a torque-limiting driver and check the head doesn't bury into a softer counterpart.

## Mating Parts for M2.5

Pair M2.5 with the matching M2.5 bolt or screw, plus a M2.5 flat washer where required to distribute load on softer materials.

Custom manufacturing · Made to drawing

## Need self-clinching threaded studs and pins in a size this table does not list?

This page covers M2.5 self-clinching threaded studs and pins. Thread, height, across-flats, property class, locking feature and flange form can all be varied, including thread sizes the standard series does not run to. Made by cold heading or tapping.

Minimum order from 2,000 pieces; samples within 7 days of drawing approval.

[Custom nut manufacturing](https://engineeringhardware.com/custom/nuts/)[Send a drawing](https://engineeringhardware.com/custom/nuts/#rfq)

## Technical Drawing

Dimensioned line drawing of M2.5 Self-Clinching Threaded Studs and Pins to Trade series (self-clinching studs and pins). Side view and top view, drawn to the dimensions in the table below and redrawn for any size selected.

- **Length options (mm):** 6 / 8 / 12 / 18
- **Head form:** flush-head stud
- **Material options:** steel / stainless steel / aluminum
- **Example installation hole (mm):** 2.5
- **Example sheet thickness (mm):** 1.0~1.95
- **Example pull-through (N):** 2600 at 1.6 mm aluminum; 2800 at 1.5 mm steel

## Dimensions & Specifications (Trade series (self-clinching studs and pins))

| Thread size | Length options (mm) | Head form | Material options | Example installation hole (mm) | Example sheet thickness (mm) | Example pull-through (N) |
| --- | --- | --- | --- | --- | --- | --- |
| M2.5 | 6 / 8 / 12 / 18 | flush-head stud | steel / stainless steel / aluminum | 2.5 | 1.0~1.95 | 2600 at 1.6 mm aluminum; 2800 at 1.5 mm steel |
| M3 | 6 / 8 / 12 / 18 | flush-head stud | steel / stainless steel / aluminum |  |  |  |

Product catalog

## Related Self-Clinching & Press-Fit Hardware products

[![Heavy-Duty Swage Turnbuckle with M8 Rigging Screws for Reliable Connections](https://img.engineeringhardware.com/Heavy-Duty-Swage-Turnbuckle-with-M8-Rigging-Screws-for-Reliable-Connections.webp)](https://engineeringhardware.com/product/heavy-duty-swage-turnbuckle-with-m8-rigging-screws-for-reliable-connections/)

Self-Clinching, Press-Fit & Swage Fasteners

### [Heavy-Duty Swage Turnbuckle with M8 Rigging Screws for Reliable Connections](https://engineeringhardware.com/product/heavy-duty-swage-turnbuckle-with-m8-rigging-screws-for-reliable-connections/)

Stud and Stud Turnbuckle · Stainless Steel

**US$0.024 – 0.048**MOQ 100 pieces

[![Factory Supply Carbon Steel Panel Fasteners Standard Screw M3m4m5m6m8m10 Flush Head Self Clinching Clinch Bolts Stud PCB Press Rivet Screws](https://img.engineeringhardware.com/Factory-Supply-Carbon-Steel-Panel-Fasteners-Standard-Screw-M3m4m5m6m8m10-Flush-Head-Self-Clinching-Clinch-Bolts-Stud-PCB-Press-Rivet-Screws.webp)](https://engineeringhardware.com/product/factory-supply-carbon-steel-panel-fasteners-standard-screw-m3m4m5m6m8m10-flush-head/)

Self-Clinching, Press-Fit & Swage Fasteners

### [Factory Supply Carbon Steel Panel Fasteners Standard Screw M3m4m5m6m8m10 Flush Head Self Clinching Clinch Bolts Stud PCB Press Rivet Screws](https://engineeringhardware.com/product/factory-supply-carbon-steel-panel-fasteners-standard-screw-m3m4m5m6m8m10-flush-head/)

Flush Head · DIN, GB, ANSI, BSW, JIS, GOST

**US$0.012 – 0.024**MOQ 1,000 pieces

[![Zinc Plated Fh Flat Head Full Thread Self Clinching Studs](https://img.engineeringhardware.com/Zinc-Plated-Fh-Flat-Head-Full-Thread-Self-Clinching-Studs.webp)](https://engineeringhardware.com/product/zinc-plated-fh-flat-head-full-thread-self-clinching-studs/)

Self-Clinching, Press-Fit & Swage Fasteners

### [Zinc Plated Fh Flat Head Full Thread Self Clinching Studs](https://engineeringhardware.com/product/zinc-plated-fh-flat-head-full-thread-self-clinching-studs/)

DIN · Carbon Steel

**US$0.0024 – 0.0072**MOQ 1,000 pieces

[![Get Blind Hole Press-Fit Standoff Hexagonal Standoff for General Hardware Assembly](https://img.engineeringhardware.com/Get-Blind-Hole-Press-Fit-Standoff-Hexagonal-Standoff-for-General-Hardware-Assembly.webp)](https://engineeringhardware.com/product/get-blind-hole-press-fit-standoff-hexagonal-standoff-for-general-hardware-assembly/)

Self-Clinching, Press-Fit & Swage Fasteners

### [Get Blind Hole Press-Fit Standoff Hexagonal Standoff for General Hardware Assembly](https://engineeringhardware.com/product/get-blind-hole-press-fit-standoff-hexagonal-standoff-for-general-hardware-assembly/)

Hexagon Head · DIN

**US$0.012 – 2.40**MOQ 100 pieces

[![Sturdy Clinch Nut for Sheet Metal Fixing with Self Clinching Profile](https://img.engineeringhardware.com/Sturdy-Clinch-Nut-for-Sheet-Metal-Fixing-with-Self-Clinching-Profile.webp)](https://engineeringhardware.com/product/sturdy-clinch-nut-for-sheet-metal-fixing-with-self-clinching-profile/)

Self-Clinching, Press-Fit & Swage Fasteners

### [Sturdy Clinch Nut for Sheet Metal Fixing with Self Clinching Profile](https://engineeringhardware.com/product/sturdy-clinch-nut-for-sheet-metal-fixing-with-self-clinching-profile/)

DIN, GB · Stainless Steel

**US$0.18 – 998.40**MOQ 2,000 pieces

[![High Quality CNC Machined Self Clinching Steel and Stainless Steel Self Clinching Nuts](https://img.engineeringhardware.com/High-Quality-CNC-Machined-Self-Clinching-Steel-and-Stainless-Steel-Self-Clinching-Nuts.webp)](https://engineeringhardware.com/product/high-quality-cnc-machined-self-clinching-steel-and-stainless-steel-self-clinching/)

Self-Clinching, Press-Fit & Swage Fasteners

### [High Quality CNC Machined Self Clinching Steel and Stainless Steel Self Clinching Nuts](https://engineeringhardware.com/product/high-quality-cnc-machined-self-clinching-steel-and-stainless-steel-self-clinching/)

Hexagon Head With Flange · DIN, ANSI, GB

**Price on request**MOQ 10 pieces

[View all Self-Clinching, Press-Fit & Swage Fasteners →](https://engineeringhardware.com/fastener-products/threaded-inserts-clinch-fasteners/self-clinching-press-fit-swage-fasteners/) [Full product catalog](https://engineeringhardware.com/products/)

## Materials & Grades

Select a material class to see the grades we supply it in. Each designation is listed with its ISO/EN, AISI/SAE, JIS and GB equivalents.

Stainless Steel38 Carbon Steel66 Alloy Steel41 Bearing Steel5 Spring Steel25 Aluminum and Aluminum Alloys21 Brass17 Bronze11 Copper8 Titanium and Titanium Alloys18 Nickel and Nickel Alloys22 Iron-Nickel and High-Temperature Alloys10 Tool Steel and Specialty Hardened Steel9 Structural and Construction Steel9

### Stainless Steel

#### Austenitic Stainless Steel

- A1 AISI 303 · SAE 303 · SUS303 · EN 1.4305 · X8CrNiS18-9
- A2 AISI 304 · SAE 304 · SUS304 · EN 1.4301 · X5CrNi18-10 · 06Cr19Ni10
- 304L AISI 304L · SUS304L · EN 1.4307 · X2CrNi18-9 · 022Cr19Ni10
- 302 AISI 302 · SUS302 · EN 1.4310
- 305 AISI 305 · SUS305 · EN 1.4303
- A4 AISI 316 · SAE 316 · SUS316 · EN 1.4401 · X5CrNiMo17-12-2 · 06Cr17Ni12Mo2
- 316L AISI 316L · SUS316L · EN 1.4404 · X2CrNiMo17-12-2 · 022Cr17Ni12Mo2
- 321 AISI 321 · SUS321 · EN 1.4541 · X6CrNiTi18-10
- 310 / 310S AISI 310 · AISI 310S · SUS310S · EN 1.4845
- 302HQ AISI 302HQ
- A3
- A5
- 347 AISI 347 · SUS347 · EN 1.4550 · X6CrNiNb18-10
- 309 / 309S AISI 309 · AISI 309S · SUS309S

#### Martensitic Stainless Steel

- AISI 410 SUS410 · EN 1.4006 · X12Cr13 · 12Cr13
- AISI 420 SUS420J1 · SUS420J2 · EN 1.4021 · EN 1.4028 · 20Cr13 · 30Cr13
- AISI 431 SUS431 · EN 1.4057 · X17CrNi16-2
- C1
- C3
- C4
- AISI 440A
- AISI 440B
- AISI 440C SUS440C · EN 1.4125

#### Ferritic Stainless Steel

- AISI 430 SUS430 · EN 1.4016 · X6Cr17 · 10Cr17
- F1
- AISI 434
- AISI 444

#### Precipitation-Hardening Stainless Steel

- 17-4 PH AISI 630 · UNS S17400 · SUS630 · EN 1.4542 · X5CrNiCuNb16-4
- 15-5 PH UNS S15500
- 17-7 PH UNS S17700

#### Duplex and Super Duplex Stainless Steel

- Duplex 2205 UNS S31803 · UNS S32205 · EN 1.4462
- Super Duplex 2507 UNS S32750 · EN 1.4410
- D2
- D4
- D6
- D8
- Lean Duplex 2101 UNS S32101
- Super Duplex S32760 UNS S32760 · EN 1.4501

### Carbon Steel

#### Low-Carbon Steel

- SAE 1006
- SAE 1008
- SAE 1010
- SAE 1018
- SAE 1020
- Q195
- Q235
- SAE 1012
- SAE 1015
- Q215
- ML08
- ML08Al
- ML10
- ML15
- ML20
- SWRCH6A
- SWRCH8A
- SWRCH10A
- SWRCH12A
- SWRCH15A
- SWRCH18A

#### Medium-Carbon Steel

- SAE 1035
- SAE 1045
- S45C
- C45
- SAE 1030
- SAE 1040
- SAE 1050
- 30
- 35
- 40
- 45
- 50
- S35C
- S40C
- S50C
- C35
- C40

#### High-Carbon Steel

- SAE 1060
- SAE 1070
- 65Mn
- SAE 1065
- SAE 1075
- SAE 1080
- SAE 1085
- SAE 1090
- SAE 1095
- 60
- 65
- 70
- 75
- 80
- 85

#### Cold-Heading Steel

- SWRCH22A
- 10B21
- SWRCH22K
- SWRCH25K
- SWRCH30K
- SWRCH35K
- SWRCH40K
- ML20Mn
- ML25
- ML30
- ML35
- ML40
- 15B25

### Alloy Steel

#### Chromium Steel

- 40Cr
- 45Cr
- AISI 5140
- SAE 5140
- AISI 5120
- SAE 5120
- SCr420
- SCr440

#### Chromium-Molybdenum Steel

- 35CrMo
- 42CrMo
- AISI 4140
- SCM435
- SCM440
- 42CrMo4
- 30CrMo
- AISI 4130
- SAE 4130
- SAE 4140
- AISI 4142
- AISI 4145
- SCM415
- SCM420
- SCM445
- EN 1.7220
- EN 1.7225
- 25CrMo4
- 34CrMo4

#### Nickel-Chromium-Molybdenum Steel

- AISI 4340
- SAE 4340
- 40CrNiMo
- SNCM439
- EN 1.6511
- 36CrNiMo4

#### Boron Alloy Steel

- 10B22
- 10B21
- 15B21
- 15B25
- 20MnTiB
- 20Mn2B
- 35VB
- 40MnB

### Bearing Steel

#### Bearing Steel

- GCr15
- AISI 52100 SAE 52100 · UNS G52986
- SUJ2
- 100Cr6 EN 1.3505
- GCr15SiMn

### Spring Steel

#### Carbon Spring Steel

- SAE 1065
- SAE 1070
- SAE 1075
- SAE 1080
- SAE 1095
- 65
- 70
- 75
- 80
- 65Mn

#### Silicon-Manganese Spring Steel

- 60Si2Mn
- 60Si2MnA
- SUP6
- SUP7

#### Chromium-Vanadium Spring Steel

- 50CrVA
- SAE 6150
- AISI 6150
- SUP10

#### Stainless Spring Steel

- AISI 301
- SUS301
- EN 1.4310
- AISI 302
- AISI 304
- AISI 316
- 17-7 PH

### Aluminum and Aluminum Alloys

#### Commercially Pure Aluminum

- 1050
- 1060
- 1070
- 1100

#### 2xxx Series Aluminum

- 2024
- 2011
- 2014
- 2017

#### 5xxx Series Aluminum

- 5052
- 5083
- 5754

#### 6xxx Series Aluminum

- 6061
- 6061-T6
- 6063
- 6082
- 6082-T6

#### 7xxx Series Aluminum

- 7075
- 7075-T6
- 7005
- 7050
- 7075-T73

### Brass

#### Free-Cutting Brass

- C36000
- H62
- HPb59-1
- C3601
- C3602
- C3604
- CuZn36Pb3
- CuZn39Pb3
- EN CW614N
- EN CW617N
- H65

#### Lead-Free Brass

- C69300
- C27450
- CW510L
- CW511L

#### Naval Brass

- C46400
- CuZn39Sn1

### Bronze

#### Silicon Bronze

- C65500
- C65100
- C65600

#### Phosphor Bronze

- C51000
- C52100
- CuSn6
- CuSn8

#### Aluminum Bronze

- C95400
- C95500
- C63000
- CuAl10Ni5Fe4

### Copper

#### Copper

- C11000
- T2
- C10100
- C10200
- C12200
- T1
- TU1
- TU2

### Titanium and Titanium Alloys

#### Commercially Pure Titanium

- Grade 2
- Grade 1
- Grade 3
- Grade 4
- TA1
- TA2
- TA3

#### Alpha-Beta Titanium Alloys

- Grade 5
- Ti-6Al-4V
- TC4
- UNS R56400

#### Low-Interstitial Grade

- Grade 23
- Ti-6Al-4V ELI
- UNS R56407

#### Other Titanium Fastener Alloys

- Ti-6Al-6V-2Sn
- Ti-6Al-2Sn-4Zr-2Mo
- Beta-C titanium
- Ti-10V-2Fe-3Al

### Nickel and Nickel Alloys

#### Commercially Pure Nickel

- Nickel 200
- UNS N02200
- Nickel 201
- UNS N02201

#### Inconel Alloys

- Inconel 625 UNS N06625
- Inconel 718 UNS N07718
- Inconel 600 UNS N06600
- Inconel 601 UNS N06601
- Inconel 686 UNS N06686
- Inconel X-750 UNS N07750

#### Monel Alloys

- Monel 400 UNS N04400
- Monel K-500 UNS N05500

#### Hastelloy Alloys

- Hastelloy C-276 UNS N10276
- Hastelloy C-22 UNS N06022
- Hastelloy B-2 UNS N10665
- Hastelloy B-3 UNS N10675
- Hastelloy X UNS N06002

#### Other Nickel Alloys

- Alloy 20 UNS N08020
- Alloy 625
- Alloy 718
- Alloy 825 UNS N08825
- Alloy 925 UNS N09925

### Iron-Nickel and High-Temperature Alloys

#### A286

- A-286
- UNS S66286
- EN 1.4980

#### Invar

- Invar 36
- Alloy 36
- UNS K93600
- FeNi36

#### Alloy 42

- Alloy 42
- UNS K94100
- FeNi42

### Tool Steel and Specialty Hardened Steel

#### Tool Steel and Specialty Hardened Steel

- AISI D2
- AISI H13
- SKD11
- Cr12MoV
- AISI O1
- AISI A2
- AISI S7
- SKD61
- 9CrSi

### Structural and Construction Steel

#### Structural and Construction Steel

- ASTM A36
- Q235B
- Q355B
- S355JR
- Q235C
- Q355C
- S235JR
- S275JR
- S355J2

## Applications & Industries for M2.5 Self-Clinching Threaded Studs and Pins

The sectors that buy Self-Clinching Threaded Studs and Pins, and the duty each one buys them for. Stocked from M2.5 to M3.

### Industries that specify Self-Clinching Threaded Studs and Pins

- **Electrical enclosures:** Panel studs hold brackets and cable hardware after forming.
- **Automotive structures:** The stud stays captive while a mating part is installed.
- **Production sheet metal:** Press installation is faster than welding a small threaded projection.
- **Chassis panels:** Flush-head studs create projecting attachment points without backside access.
- **Building services:** Threaded rod, channel and suspension assemblies.
- **Machine building & OEM:** The clamping counter-face on studs and bolts throughout an assembly.

### Typical applications

- choosing 6, 8, 12 or 18 mm length
- checking pull-through against the actual sheet and material
- using the stud as a projecting threaded attachment point
- installing a flush-head threaded stud in prepared sheet
- joints re-torqued at a service interval
- completing a bolted joint on a stud, rod or bolt

### Service conditions to specify against

- **Marine and coastal:** Available in A4 (316) stainless for chloride exposure — coastal structures, pool halls, water treatment and deck hardware, where A2 will eventually pit.
- **High load:** Supplied in ISO 898-1 property classes, so the joint can be designed to a stated proof load and tightened to a calculated torque rather than by feel.
- **Match the class:** A nut below the bolt property class strips before the bolt reaches its own limit — pair class 8 nuts with 8.8 bolts, class 10 with 10.9.

### Where to use something else

- Do not reuse the example pull-through force as a universal rating; sheet alloy and thickness change the result.

[Full application guide: where Self-Clinching Threaded Studs and Pins are used, how to specify them, and the cases they are wrong for](https://engineeringhardware.com/applications/self-clinching-threaded-studs-and-pins/)

Inside the plant

## Manufactured in our own plant

This part is cold-formed, threaded, heat-treated and finished in-house. The stages below are where its class and finish are actually decided.

1. ![Wire rod feeding into a cold heading machine](https://engineeringhardware.com/wp-content/uploads/2026/08/09-wire-rod-feed-cold-heading-machine.webp) 01 **Cold heading** Wire rod is drawn to size and cold-formed into blanks. Forming rather than cutting keeps the grain flow continuous around the head, which is where a bolt is most likely to fail. Head dimensions and under-head radius checked at set-up and per shift.
2. ![Thread rolling machine producing bolt threads](https://engineeringhardware.com/wp-content/uploads/2026/08/03-thread-rolling-machine-bolt-production.webp) 02 **Thread rolling** Threads are rolled between hardened dies rather than cut. Rolled threads are stronger in fatigue than cut threads and hold pitch and flank angle far more consistently across a batch. Go / no-go ring gauges to ISO 965 tolerance class 6g.
3. ![Baskets of bolts staged for heat treatment](https://engineeringhardware.com/wp-content/uploads/2026/08/05-heat-treatment-baskets-black-bolts.webp) 03 **Heat treatment** Quench-and-temper brings carbon and alloy steel to the property class ordered — 8.8, 10.9 or 12.9 — with the furnace charge tracked so a finished lot can be traced back to it. Core hardness and tensile tested per lot to ISO 898-1.
4. ![Zinc plated bolts in a treatment basket](https://engineeringhardware.com/wp-content/uploads/2026/08/23-zinc-plated-bolts-treatment-basket.webp) 04 **Surface treatment** Zinc, zinc-nickel, hot-dip galvanizing, black oxide, phosphate and Dacromet, selected against the service environment rather than against the price list. Coating thickness and neutral salt spray hours to ISO 9227.

## Frequently Asked Questions

### What is the coarse-thread pitch of M2.5 for Self-Clinching Threaded Studs and Pins?

For M2.5 the standard coarse pitch is 0.45 mm — this is the value used for Self-Clinching Threaded Studs and Pins.

### What clearance and tapping drill suit M2.5?

Use a 2.9 mm clearance hole (ISO 273 medium) for through-fixing, or a 2.05 mm tapping drill for a coarse M2.5 thread.

### Is M2.5 Self-Clinching Threaded Studs and Pins suitable for electronics and small mechanisms?

M2.5 Self-Clinching Threaded Studs and Pins is in the micro range and is widely used in electronics, instrument enclosures and small precision mechanisms. Watch the over-torque margin — micro joints strip easily.

### What's the typical proof load behavior of M2.5 class 8.8?

Micro-thread joints are sensitive to plastic deformation in the first turn under load — use a torque-limiting driver and check the bearing surface deformation on softer mating materials.

### How do I request a quotation?

Use the technical drawing on this page to pick the exact configuration, then submit it with the quote form. We respond within one business day.

## Related Pages

[View the full Self-Clinching Threaded Studs and Pins page](https://engineeringhardware.com/fastener/self-clinching-threaded-studs-and-pins/)

### More Self-Clinching Threaded Studs and Pins Guides