This page covers M2 Hexalobular Socket Oval Countersunk Head Screws to ISO 14584: the full dimensional row, hole and tool sizes, proof-load data and typical applications. All values are taken from the governing standards (ISO 14584 together with ISO 273, ISO 724 and ISO 898-1 where applicable).
M2 Dimensional Row (ISO 14584)
| Size | Pitch P (mm) | b (mm) | Head diameter dk (mm) | csh_diam (mm) | f (mm) | csh_height (mm) | r (mm) | rf (mm) | x (mm) | tt (mm) | A (mm) | t_mean (mm) | Length range l (mm) | Reference standard |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| M2 | 0.4 | 25.0 | 4.4 | 3.8 | 0.5 | 1.2 | 0.2 | 4.0 | 1.0 | T6 | 1.75 | 0.7 | 3~20 | ISO 14584 |
Spanner & Drive for M2 Hexalobular Socket Oval Countersunk Head Screws
Drive geometry for M2 Hexalobular Socket Oval Countersunk Head Screws is given by the row above; match the tool to the listed values.
Hole Sizes for M2
| Coarse-thread pitch (ISO 724) | 0.4 mm |
|---|---|
| Through-hole / clearance (ISO 273 medium) | 2.4 mm |
| Tapping drill, coarse thread | 1.6 mm |
Tightening Torque for M2
| Class 8.8 (dry, ~µ 0.125) | ≈ 0.3 Nm |
|---|---|
| Class 10.9 (dry, ~µ 0.125) | ≈ Nm |
| Class 12.9 (dry, ~µ 0.125) | ≈ 0.6 Nm |
Indicative dry-joint values. Lubrication can lower the required torque by 15–25%. Always confirm against the joint design, especially when going up a strength class.
Proof Load & Strength for M2
| Tensile stress area As (ISO 724) | 2.1 mm² |
|---|---|
| Proof load, class 8.8 | 1.2 kN |
| Proof load, class 12.9 | 2 kN |
| Min. ultimate tensile load, class 8.8 | 1.7 kN |
Proof load = tensile stress area × the proof stress Sp of the class, per ISO 898-1 — Sp is a lower figure than the yield stress Rp0.2 and the two are not interchangeable. The stress area is computed from this size's own diameter and pitch, so a fine-pitch designation gives the fine-pitch figure. Design the joint so the working preload stays below the proof load of the class selected.
M2 Hexalobular Socket Oval Countersunk Head Screws Weight
A steel M2 hexalobular socket oval countersunk head screws at the listed 320 mm length weighs approximately 38 g each — about 38 kg per 1,000 pieces. Stainless A2/A4 weighs roughly the same (density 7.9–8.0 g/cm³).
Actual weight varies slightly with head form, thread and finish; use this figure for freight estimation only.
Installation Tips for M2 Hexalobular Socket Oval Countersunk Head Screws
- At M2 the joint is sensitive to over-torque — use a torque-limiting driver and check the head doesn't bury into a softer counterpart.
Mating Parts for M2
For M2, pair with a M2 hex nut (ISO 4032 / DIN 934) and, where used, a M2 flat washer (ISO 7089 / DIN 125A) under the head and under the nut.
Custom manufacturing · Made to drawing
Need hexalobular socket oval countersunk head screws in a size this table does not list?
This page covers M2 hexalobular socket oval countersunk head screws. Material and finish are usually what drives a special — a grade the standard part is not stocked in, or a coating chosen against a salt-spray figure instead of a default. Made by cold heading or warm forging.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
