---
title: "M24 Fitted (Reamer) Bolts, DIN 609 Dimensions"
description: "M24 Fitted (Reamer) Bolts, DIN 609: width across flats (spanner size) 36 mm, head height 15 mm, coarse thread pitch 3 mm."
url: https://engineeringhardware.com/guide/size/m24-fitted-bolts-din-609/
source: Engineering Hardware & Fasteners
---

# M24 Fitted (Reamer) Bolts, DIN 609 Dimensions

Bolts · DIN 609

Controlling dimensions to DIN 609, with clearance hole and tapping drill, spanner or drive size and tightening torque.

M24 Fitted (Reamer) Bolts, DIN 609 dimensions to DIN 609: width across flats (spanner size) 36 mm, head height 15 mm, coarse thread pitch 3 mm, clearance hole (ISO 273 medium) 26 mm. Tighten to approximately 726 Nm at property class 8.8 in a dry, as-supplied condition.

- **Width across flats (spanner size):** 36 mm
- **Head height:** 15 mm
- **Coarse thread pitch:** 3 mm
- **Clearance hole (ISO 273 medium):** 26 mm
- **Tightening torque (class 8.8):** 726 Nm

Figures are nominal values from the governing standard. Confirm against the tolerance class for your application before machining or ordering.

![M24 Fitted (Reamer) Bolts, DIN 609 Dimensions reference image](https://engineeringhardware.com/wp-content/uploads/2026/09/Fitted-Bolts-DIN-609.webp)

The M24 size of Fitted (Reamer) Bolts, DIN 609 is dimensioned by DIN 609. The tables below give the dimensional row from the standard, the drill and spanner sizes that go with it, and the assembly torque per property class. The technical drawing on this page redraws to the exact values selected.

## M24 Dimensional Row (DIN 609)

| Thread size | Shank diameter ds k6 (mm) | Reamed hole H7 (mm) | Width across flats s (mm) | Head height k (mm) | Common length range (mm) | Property class | Reference standard |
| --- | --- | --- | --- | --- | --- | --- | --- |
| M24 | 25 | 25 | 36 | 15.0 | 70~200 | 8.8 | DIN 609 |

## Spanner & Drive for M24 Fitted (Reamer) Bolts, DIN 609

Drive geometry for M24 Fitted (Reamer) Bolts, DIN 609 is given by the row above; match the tool to the listed values.

## Hole Sizes for M24

| Coarse-thread pitch (ISO 724) | 3 mm |
| --- | --- |
| Through-hole / clearance (ISO 273 medium) | 26 mm |
| Tapping drill, coarse thread | 21 mm |

## Tightening Torque for M24

| Class 8.8 (dry, ~µ 0.125) | ≈ 726 Nm |
| --- | --- |
| Class 10.9 (dry, ~µ 0.125) | ≈ 1034 Nm |
| Class 12.9 (dry, ~µ 0.125) | ≈ 1210 Nm |

Indicative dry-joint values. Lubrication can lower the required torque by 15–25%. Always confirm against the joint design, especially when going up a strength class.

## Proof Load & Strength for M24

| Tensile stress area As (ISO 724) | 353 mm² |
| --- | --- |
| Proof load, class 8.8 | 212 kN |
| Proof load, class 10.9 | 293 kN |
| Proof load, class 12.9 | 342 kN |
| Min. ultimate tensile load, class 8.8 | 293 kN |

Proof load = tensile stress area × the proof stress Sp of the class, per ISO 898-1 — Sp is a lower figure than the yield stress Rp0.2 and the two are not interchangeable. The stress area is computed from this size's own diameter and pitch, so a fine-pitch designation gives the fine-pitch figure. Design the joint so the working preload stays below the proof load of the class selected.

## M24 Fitted (Reamer) Bolts, DIN 609 Weight

A steel M24 fitted (reamer) bolts, din 609 at the listed 70,200 mm length weighs approximately 270,638 g each — about 270,638 kg per 1,000 pieces. Stainless A2/A4 weighs roughly the same (density 7.9–8.0 g/cm³).

Actual weight varies slightly with head form, thread and finish; use this figure for freight estimation only.

## Installation Tips for M24 Fitted (Reamer) Bolts, DIN 609

- At M24 the stretch in the bolt becomes the controlling factor — for critical joints, use angle-controlled or stretch-controlled tightening instead of pure torque.

## Mating Parts for M24

For M24, pair with a M24 hex nut (ISO 4032 / DIN 934) and, where used, a M24 flat washer (ISO 7089 / DIN 125A) under the head and under the nut.

Custom manufacturing · Made to drawing

## Need fitted (reamer) bolts, DIN 609 in a size this table does not list?

This page covers M24 fitted (reamer) bolts, DIN 609. Thread size and pitch, length, property class, drive form, head geometry and head marking are all specifiable — the standard part is where it starts, not where it stops. Made by cold heading or hot forging.

Minimum order from 2,000 pieces; samples within 7 days of drawing approval.

[Custom bolt manufacturing](https://engineeringhardware.com/custom/bolts/)[Send a drawing](https://engineeringhardware.com/custom/bolts/#rfq)

## Technical Drawing

Dimensioned line drawing of M24 Fitted (Reamer) Bolts, DIN 609 to DIN 609. Side view and top view, drawn to the dimensions in the table below and redrawn for any size selected.

- **Shank diameter ds k6 (mm):** 25
- **Reamed hole H7 (mm):** 25
- **Width across flats s (mm):** 36
- **Head height k (mm):** 15.0
- **Common length range (mm):** 70~200
- **Property class:** 8.8

## Dimensions & Specifications (DIN 609)

| Thread size | Shank diameter ds k6 (mm) | Reamed hole H7 (mm) | Width across flats s (mm) | Head height k (mm) | Common length range (mm) | Property class | Reference standard |
| --- | --- | --- | --- | --- | --- | --- | --- |
| M8 | 9 | 9 | 13 | 5.3 | 30~80 | 8.8 | DIN 609 |
| M10 | 11 | 11 | 17 | 6.4 | 35~100 | 8.8 | DIN 609 |
| M12 | 13 | 13 | 19 | 7.5 | 40~120 | 8.8 | DIN 609 |
| M16 | 17 | 17 | 24 | 10.0 | 50~150 | 8.8 | DIN 609 |
| M20 | 21 | 21 | 30 | 12.5 | 60~180 | 8.8 | DIN 609 |
| M24 | 25 | 25 | 36 | 15.0 | 70~200 | 8.8 | DIN 609 |

Product catalog

## Related Fitted (Reamer) Bolts products

[![M8-M14 Metric Fine Grade 8.8/10.9 High Tensile Yellow Zinc Steel Hex Bolts](https://img.engineeringhardware.com/M8-M14-Metric-Fine-Grade-8-8-10-9-High-Tensile-Yellow-Zinc-Steel-Hex-Bolts.webp)](https://engineeringhardware.com/product/m8-m14-metric-fine-grade-8-8-10-9-high-tensile-yellow-zinc-steel-hex-bolts/)

Hex-Head Bolts

### [M8-M14 Metric Fine Grade 8.8/10.9 High Tensile Yellow Zinc Steel Hex Bolts](https://engineeringhardware.com/product/m8-m14-metric-fine-grade-8-8-10-9-high-tensile-yellow-zinc-steel-hex-bolts/)

Hexagon Head · DIN, ANSI, GB, JIS, BSW, GOST

**US$0.11 – 0.16**MOQ 1 piece

[![DIN933/DIN 6914/ASME B 18.2.1/Uni 5712/ISO 7411/JIS B 1186/En 14399-4/GB /T 1231 Customizable Gold Thickness Gold Plated Hex Head Bolts](https://img.engineeringhardware.com/DIN933-DIN-6914-ASME-B-18-2-1-Uni-5712-ISO-7411-JIS-B-1186-En-14399-4-GB-T-1231-Customizable-Gold-Thickness-Gold-Plated-Hex-Head-Bolts.webp)](https://engineeringhardware.com/product/din933-din-6914-asme-b-18-2-1-uni-5712-iso-7411-jis-b-1186-en-14399-4-gb-t-1231/)

Hex-Head Bolts

### [DIN933/DIN 6914/ASME B 18.2.1/Uni 5712/ISO 7411/JIS B 1186/En 14399-4/GB /T 1231 Customizable Gold Thickness Gold Plated Hex Head Bolts](https://engineeringhardware.com/product/din933-din-6914-asme-b-18-2-1-uni-5712-iso-7411-jis-b-1186-en-14399-4-gb-t-1231/)

Hexagon Head · DIN, ANSI, GB, JIS, BSW, GOST

**US$0.14**MOQ 100 pieces

[![Ningbo-Bolt Heavy Duty Hardware Fasteners](https://img.engineeringhardware.com/Ningbo-Bolt-Heavy-Duty-Hardware-Fasteners.webp)](https://engineeringhardware.com/product/ningbo-bolt-heavy-duty-hardware-fasteners/)

Hex-Head Bolts

### [Ningbo-Bolt Heavy Duty Hardware Fasteners](https://engineeringhardware.com/product/ningbo-bolt-heavy-duty-hardware-fasteners/)

Hexagon Head · Custom

**US$0.12 – 1.20**MOQ 1,000 pieces

[![Carbon Steel Slotted Hex Screw Cross Recessed Hexagon Slotted Bolt](https://img.engineeringhardware.com/Carbon-Steel-Slotted-Hex-Screw-Cross-Recessed-Hexagon-Slotted-Bolt.webp)](https://engineeringhardware.com/product/carbon-steel-slotted-hex-screw-cross-recessed-hexagon-slotted-bolt/)

Hex-Head Bolts

### [Carbon Steel Slotted Hex Screw Cross Recessed Hexagon Slotted Bolt](https://engineeringhardware.com/product/carbon-steel-slotted-hex-screw-cross-recessed-hexagon-slotted-bolt/)

Hexagon Head · DIN

**US$0.012**MOQ 1,000 pieces

[![Premium M8-0.8×10mm Hexagonal Bolt Made of 304 Stainless Steel](https://img.engineeringhardware.com/Premium-M8-0-8-10mm-Hexagonal-Bolt-Made-of-304-Stainless-Steel.webp)](https://engineeringhardware.com/product/premium-m8-0-810mm-hexagonal-bolt-made-of-304-stainless-steel/)

Hex-Head Bolts

### [Premium M8-0.8×10mm Hexagonal Bolt Made of 304 Stainless Steel](https://engineeringhardware.com/product/premium-m8-0-810mm-hexagonal-bolt-made-of-304-stainless-steel/)

Cold Stamping · Carbon Steel

**US$0.012 – 0.60**MOQ 1,000 pieces

[![China Wholesale Stainless Steel Hex Head Nut and Bolt DIN 931](https://img.engineeringhardware.com/China-Wholesale-Stainless-Steel-Hex-Head-Nut-and-Bolt-DIN-931.webp)](https://engineeringhardware.com/product/china-wholesale-stainless-steel-hex-head-nut-and-bolt-din-931/)

Hex-Head Bolts

### [China Wholesale Stainless Steel Hex Head Nut and Bolt DIN 931](https://engineeringhardware.com/product/china-wholesale-stainless-steel-hex-head-nut-and-bolt-din-931/)

Hexagon Head · DIN, ANSI, GB, BSW, ASME

**US$0.0012 – 0.60**MOQ 1 piece

[View all Hex-Head Bolts →](https://engineeringhardware.com/fastener-products/bolts/hex-head-bolts/) [Full product catalog](https://engineeringhardware.com/products/)

## Materials & Grades

Select a material class to see the grades we supply it in. Each designation is listed with its ISO/EN, AISI/SAE, JIS and GB equivalents.

Stainless Steel38 Carbon Steel66 Alloy Steel41 Bearing Steel5 Spring Steel25 Aluminum and Aluminum Alloys21 Brass17 Bronze11 Copper8 Titanium and Titanium Alloys18 Nickel and Nickel Alloys22 Iron-Nickel and High-Temperature Alloys10 Tool Steel and Specialty Hardened Steel9 Structural and Construction Steel9

### Stainless Steel

#### Austenitic Stainless Steel

- A1 AISI 303 · SAE 303 · SUS303 · EN 1.4305 · X8CrNiS18-9
- A2 AISI 304 · SAE 304 · SUS304 · EN 1.4301 · X5CrNi18-10 · 06Cr19Ni10
- 304L AISI 304L · SUS304L · EN 1.4307 · X2CrNi18-9 · 022Cr19Ni10
- 302 AISI 302 · SUS302 · EN 1.4310
- 305 AISI 305 · SUS305 · EN 1.4303
- A4 AISI 316 · SAE 316 · SUS316 · EN 1.4401 · X5CrNiMo17-12-2 · 06Cr17Ni12Mo2
- 316L AISI 316L · SUS316L · EN 1.4404 · X2CrNiMo17-12-2 · 022Cr17Ni12Mo2
- 321 AISI 321 · SUS321 · EN 1.4541 · X6CrNiTi18-10
- 310 / 310S AISI 310 · AISI 310S · SUS310S · EN 1.4845
- 302HQ AISI 302HQ
- A3
- A5
- 347 AISI 347 · SUS347 · EN 1.4550 · X6CrNiNb18-10
- 309 / 309S AISI 309 · AISI 309S · SUS309S

#### Martensitic Stainless Steel

- AISI 410 SUS410 · EN 1.4006 · X12Cr13 · 12Cr13
- AISI 420 SUS420J1 · SUS420J2 · EN 1.4021 · EN 1.4028 · 20Cr13 · 30Cr13
- AISI 431 SUS431 · EN 1.4057 · X17CrNi16-2
- C1
- C3
- C4
- AISI 440A
- AISI 440B
- AISI 440C SUS440C · EN 1.4125

#### Ferritic Stainless Steel

- AISI 430 SUS430 · EN 1.4016 · X6Cr17 · 10Cr17
- F1
- AISI 434
- AISI 444

#### Precipitation-Hardening Stainless Steel

- 17-4 PH AISI 630 · UNS S17400 · SUS630 · EN 1.4542 · X5CrNiCuNb16-4
- 15-5 PH UNS S15500
- 17-7 PH UNS S17700

#### Duplex and Super Duplex Stainless Steel

- Duplex 2205 UNS S31803 · UNS S32205 · EN 1.4462
- Super Duplex 2507 UNS S32750 · EN 1.4410
- D2
- D4
- D6
- D8
- Lean Duplex 2101 UNS S32101
- Super Duplex S32760 UNS S32760 · EN 1.4501

### Carbon Steel

#### Low-Carbon Steel

- SAE 1006
- SAE 1008
- SAE 1010
- SAE 1018
- SAE 1020
- Q195
- Q235
- SAE 1012
- SAE 1015
- Q215
- ML08
- ML08Al
- ML10
- ML15
- ML20
- SWRCH6A
- SWRCH8A
- SWRCH10A
- SWRCH12A
- SWRCH15A
- SWRCH18A

#### Medium-Carbon Steel

- SAE 1035
- SAE 1045
- S45C
- C45
- SAE 1030
- SAE 1040
- SAE 1050
- 30
- 35
- 40
- 45
- 50
- S35C
- S40C
- S50C
- C35
- C40

#### High-Carbon Steel

- SAE 1060
- SAE 1070
- 65Mn
- SAE 1065
- SAE 1075
- SAE 1080
- SAE 1085
- SAE 1090
- SAE 1095
- 60
- 65
- 70
- 75
- 80
- 85

#### Cold-Heading Steel

- SWRCH22A
- 10B21
- SWRCH22K
- SWRCH25K
- SWRCH30K
- SWRCH35K
- SWRCH40K
- ML20Mn
- ML25
- ML30
- ML35
- ML40
- 15B25

### Alloy Steel

#### Chromium Steel

- 40Cr
- 45Cr
- AISI 5140
- SAE 5140
- AISI 5120
- SAE 5120
- SCr420
- SCr440

#### Chromium-Molybdenum Steel

- 35CrMo
- 42CrMo
- AISI 4140
- SCM435
- SCM440
- 42CrMo4
- 30CrMo
- AISI 4130
- SAE 4130
- SAE 4140
- AISI 4142
- AISI 4145
- SCM415
- SCM420
- SCM445
- EN 1.7220
- EN 1.7225
- 25CrMo4
- 34CrMo4

#### Nickel-Chromium-Molybdenum Steel

- AISI 4340
- SAE 4340
- 40CrNiMo
- SNCM439
- EN 1.6511
- 36CrNiMo4

#### Boron Alloy Steel

- 10B22
- 10B21
- 15B21
- 15B25
- 20MnTiB
- 20Mn2B
- 35VB
- 40MnB

### Bearing Steel

#### Bearing Steel

- GCr15
- AISI 52100 SAE 52100 · UNS G52986
- SUJ2
- 100Cr6 EN 1.3505
- GCr15SiMn

### Spring Steel

#### Carbon Spring Steel

- SAE 1065
- SAE 1070
- SAE 1075
- SAE 1080
- SAE 1095
- 65
- 70
- 75
- 80
- 65Mn

#### Silicon-Manganese Spring Steel

- 60Si2Mn
- 60Si2MnA
- SUP6
- SUP7

#### Chromium-Vanadium Spring Steel

- 50CrVA
- SAE 6150
- AISI 6150
- SUP10

#### Stainless Spring Steel

- AISI 301
- SUS301
- EN 1.4310
- AISI 302
- AISI 304
- AISI 316
- 17-7 PH

### Aluminum and Aluminum Alloys

#### Commercially Pure Aluminum

- 1050
- 1060
- 1070
- 1100

#### 2xxx Series Aluminum

- 2024
- 2011
- 2014
- 2017

#### 5xxx Series Aluminum

- 5052
- 5083
- 5754

#### 6xxx Series Aluminum

- 6061
- 6061-T6
- 6063
- 6082
- 6082-T6

#### 7xxx Series Aluminum

- 7075
- 7075-T6
- 7005
- 7050
- 7075-T73

### Brass

#### Free-Cutting Brass

- C36000
- H62
- HPb59-1
- C3601
- C3602
- C3604
- CuZn36Pb3
- CuZn39Pb3
- EN CW614N
- EN CW617N
- H65

#### Lead-Free Brass

- C69300
- C27450
- CW510L
- CW511L

#### Naval Brass

- C46400
- CuZn39Sn1

### Bronze

#### Silicon Bronze

- C65500
- C65100
- C65600

#### Phosphor Bronze

- C51000
- C52100
- CuSn6
- CuSn8

#### Aluminum Bronze

- C95400
- C95500
- C63000
- CuAl10Ni5Fe4

### Copper

#### Copper

- C11000
- T2
- C10100
- C10200
- C12200
- T1
- TU1
- TU2

### Titanium and Titanium Alloys

#### Commercially Pure Titanium

- Grade 2
- Grade 1
- Grade 3
- Grade 4
- TA1
- TA2
- TA3

#### Alpha-Beta Titanium Alloys

- Grade 5
- Ti-6Al-4V
- TC4
- UNS R56400

#### Low-Interstitial Grade

- Grade 23
- Ti-6Al-4V ELI
- UNS R56407

#### Other Titanium Fastener Alloys

- Ti-6Al-6V-2Sn
- Ti-6Al-2Sn-4Zr-2Mo
- Beta-C titanium
- Ti-10V-2Fe-3Al

### Nickel and Nickel Alloys

#### Commercially Pure Nickel

- Nickel 200
- UNS N02200
- Nickel 201
- UNS N02201

#### Inconel Alloys

- Inconel 625 UNS N06625
- Inconel 718 UNS N07718
- Inconel 600 UNS N06600
- Inconel 601 UNS N06601
- Inconel 686 UNS N06686
- Inconel X-750 UNS N07750

#### Monel Alloys

- Monel 400 UNS N04400
- Monel K-500 UNS N05500

#### Hastelloy Alloys

- Hastelloy C-276 UNS N10276
- Hastelloy C-22 UNS N06022
- Hastelloy B-2 UNS N10665
- Hastelloy B-3 UNS N10675
- Hastelloy X UNS N06002

#### Other Nickel Alloys

- Alloy 20 UNS N08020
- Alloy 625
- Alloy 718
- Alloy 825 UNS N08825
- Alloy 925 UNS N09925

### Iron-Nickel and High-Temperature Alloys

#### A286

- A-286
- UNS S66286
- EN 1.4980

#### Invar

- Invar 36
- Alloy 36
- UNS K93600
- FeNi36

#### Alloy 42

- Alloy 42
- UNS K94100
- FeNi42

### Tool Steel and Specialty Hardened Steel

#### Tool Steel and Specialty Hardened Steel

- AISI D2
- AISI H13
- SKD11
- Cr12MoV
- AISI O1
- AISI A2
- AISI S7
- SKD61
- 9CrSi

### Structural and Construction Steel

#### Structural and Construction Steel

- ASTM A36
- Q235B
- Q355B
- S355JR
- Q235C
- Q355C
- S235JR
- S275JR
- S355J2

## Applications & Industries for M24 Fitted Bolts

Fitted Bolts are bought for a small number of well-defined jobs. These are the ones we ship them for. Stocked from M8 to M24.

### Industries that specify Fitted Bolts

- **Gearbox & housing assembly:** Split housings that must reassemble in exactly the same position.
- **Press & die sets:** Located joints carrying shear across the parting line.
- **Machine tools:** Joints where the bolt locates the two halves as well as clamping them.
- **Automotive & transport:** Chassis, driveline and body fixings that see vibration and are assembled to a controlled preload.
- **Steel fabrication:** Bolted connections in frames, enclosures, walkways and weldments, on the bench and on site.
- **Energy & infrastructure:** Tower, pipework, switchgear and plant fixings specified for long service life and inspectable joints.

### Typical applications

- locating two parts within a few hundredths of a millimetre
- reamed H7 holes matched to a k6 ground shank
- transmitting shear on the shank rather than by friction
- joints where the property class is stated on the drawing
- clamping two machined faces to a calculated preload
- bolting brackets, motors and gearboxes to a frame

### Service conditions to specify against

- **Marine and coastal:** Available in A4 (316) stainless for chloride exposure — coastal structures, pool halls, water treatment and deck hardware, where A2 will eventually pit.
- **High load:** Supplied in ISO 898-1 property classes, so the joint can be designed to a stated proof load and tightened to a calculated torque rather than by feel.
- **Torque and preload:** The joint is designed around bolt tension, so lubrication, coating and the friction coefficient all change the torque figure — state them together.

### Where to use something else

- Do not use a machine thread into unthreaded sheet or timber; use a tapping screw, rivet nut or insert made for that parent material.

[Full application guide: where Fitted Bolts are used, how to specify them, and the cases they are wrong for](https://engineeringhardware.com/applications/fitted-bolts-din-609/)

Inside the plant

## Manufactured in our own plant

This part is cold-formed, threaded, heat-treated and finished in-house. The stages below are where its class and finish are actually decided.

1. ![Wire rod feeding into a cold heading machine](https://engineeringhardware.com/wp-content/uploads/2026/08/09-wire-rod-feed-cold-heading-machine.webp) 01 **Cold heading** Wire rod is drawn to size and cold-formed into blanks. Forming rather than cutting keeps the grain flow continuous around the head, which is where a bolt is most likely to fail. Head dimensions and under-head radius checked at set-up and per shift.
2. ![Thread rolling machine producing bolt threads](https://engineeringhardware.com/wp-content/uploads/2026/08/03-thread-rolling-machine-bolt-production.webp) 02 **Thread rolling** Threads are rolled between hardened dies rather than cut. Rolled threads are stronger in fatigue than cut threads and hold pitch and flank angle far more consistently across a batch. Go / no-go ring gauges to ISO 965 tolerance class 6g.
3. ![Baskets of bolts staged for heat treatment](https://engineeringhardware.com/wp-content/uploads/2026/08/05-heat-treatment-baskets-black-bolts.webp) 03 **Heat treatment** Quench-and-temper brings carbon and alloy steel to the property class ordered — 8.8, 10.9 or 12.9 — with the furnace charge tracked so a finished lot can be traced back to it. Core hardness and tensile tested per lot to ISO 898-1.
4. ![Zinc plated bolts in a treatment basket](https://engineeringhardware.com/wp-content/uploads/2026/08/23-zinc-plated-bolts-treatment-basket.webp) 04 **Surface treatment** Zinc, zinc-nickel, hot-dip galvanizing, black oxide, phosphate and Dacromet, selected against the service environment rather than against the price list. Coating thickness and neutral salt spray hours to ISO 9227.

## Frequently Asked Questions

### What clearance and tapping drill suit M24?

Use a 26 mm clearance hole (ISO 273 medium) for through-fixing, or a 21 mm tapping drill for a coarse M24 thread.

### Should M24 Fitted (Reamer) Bolts, DIN 609 be tightened by torque or by angle?

For critical structural joints at M24, angle-controlled or stretch-controlled tightening is more repeatable than pure torque — the friction scatter at large diameters can dominate the torque signal.

### What grip range is typical for M24 structural bolts?

Grip ranges are highly application-dependent at M24. As a guide, choose a length that gives at least 1× the thread diameter engagement in the nut plus 2–3 thread pitches projecting.

### What is the coarse-thread pitch of M24 for Fitted (Reamer) Bolts, DIN 609?

For M24 the standard coarse pitch is 3 mm — this is the value used for Fitted (Reamer) Bolts, DIN 609.

### How do I request a quotation?

Use the technical drawing on this page to pick the exact configuration, then submit it with the quote form. We respond within one business day.

## Related Pages

[View the full Fitted (Reamer) Bolts, DIN 609 page](https://engineeringhardware.com/fastener/fitted-bolts-din-609/)

### More Fitted (Reamer) Bolts, DIN 609 Guides