---
title: "M24 T-Slot Nuts Dimensions"
description: "M24 T-Slot Nuts: nut height 30 mm, coarse thread pitch 3 mm. Tightening torque 726 Nm at class 8.8. Full size chart to DIN 508 with tolerances."
url: https://engineeringhardware.com/guide/size/m24-t-slot-nuts/
source: Engineering Hardware & Fasteners
---

# M24 T-Slot Nuts Dimensions

Nuts · DIN 508

Controlling dimensions to DIN 508, with spanner or drive size and tightening torque.

M24 T-Slot Nuts dimensions to DIN 508: nut height 30 mm, coarse thread pitch 3 mm. Tighten to approximately 726 Nm at property class 8.8 in a dry, as-supplied condition.

- **Nut height:** 30 mm
- **Coarse thread pitch:** 3 mm
- **Tightening torque (class 8.8):** 726 Nm

Figures are nominal values from the governing standard. Confirm against the tolerance class for your application before machining or ordering.

![M24 T-Slot Nuts Dimensions reference image](https://engineeringhardware.com/wp-content/uploads/2026/06/T-Slot-Nuts-—-DIN-508.webp)

M24 T-Slot Nuts are manufactured to DIN 508. This page lists the controlling dimensions for the M24 size together with the drive and the installation notes for this type.

Values are taken from the governing standard rather than from a general machine-thread table, because this type is not selected on one.

## M24 Dimensional Row (DIN 508)

| Thread size | T-slot width (mm) | Nut width b (mm) | Total height h (mm) | Key height h1 (mm) | Hook width e (mm) | Reference standard |
| --- | --- | --- | --- | --- | --- | --- |
| M24 | 28 | 32.0 | 30.0 | 18.0 | 28.4 | DIN 508 / GN505 |

## Spanner & Drive for M24 T-Slot Nuts

Drive geometry for M24 T-Slot Nuts is given by the row above; match the tool to the listed values.

## Tightening Torque for M24

| Class 8.8 (dry, ~µ 0.125) | ≈ 726 Nm |
| --- | --- |
| Class 10.9 (dry, ~µ 0.125) | ≈ 1034 Nm |
| Class 12.9 (dry, ~µ 0.125) | ≈ 1210 Nm |

Indicative dry-joint values. Lubrication can lower the required torque by 15–25%. Always confirm against the joint design, especially when going up a strength class.

## Proof Load & Strength for M24

Nuts are graded to ISO 898-2 by the proof load the nut itself will hold (classes 04, 05, 5, 6, 8, 10 and 12), not by the 8.8 / 10.9 / 12.9 scale used for bolts. A class-8 nut is the correct mate for a class-8.8 bolt, and the joint is designed on the bolt, so no bolt-tension figure is quoted here.

## Installation Tips for M24 T-Slot Nuts

- At M24 the stretch in the bolt becomes the controlling factor — for critical joints, use angle-controlled or stretch-controlled tightening instead of pure torque.

## Mating Parts for M24

Pair M24 with the matching M24 bolt or screw, plus a M24 flat washer where required to distribute load on softer materials.

Custom manufacturing · Made to drawing

## Need t-slot nuts in a size this table does not list?

This page covers M24 t-slot nuts. Locking method is specifiable independently of the rest: nylon insert, all-metal deformed thread, serrated flange, or none. Made by cold heading or tapping.

Minimum order from 2,000 pieces; samples within 7 days of drawing approval.

[Custom nut manufacturing](https://engineeringhardware.com/custom/nuts/)[Send a drawing](https://engineeringhardware.com/custom/nuts/#rfq)

## Technical Drawing

Dimensioned line drawing of M24 T-Slot Nuts to DIN 508. Side view and top view, drawn to the dimensions in the table below and redrawn for any size selected.

- **T-slot width (mm):** 28
- **Nut width b (mm):** 32.0
- **Total height h (mm):** 30.0
- **Key height h1 (mm):** 18.0
- **Hook width e (mm):** 28.4

## Dimensions & Specifications (DIN 508)

| Thread size | T-slot width (mm) | Nut width b (mm) | Total height h (mm) | Key height h1 (mm) | Hook width e (mm) | Reference standard |
| --- | --- | --- | --- | --- | --- | --- |
| M5 | 6 | 8.0 | 8.0 | 4.5 | 6.4 | DIN 508 / GN505 |
| M6 | 8 | 10.0 | 10.0 | 5.5 | 8.4 | DIN 508 / GN505 |
| M8 | 10 | 12.0 | 12.0 | 7.0 | 10.4 | DIN 508 / GN505 |
| M8 | 12 | 14.0 | 12.0 | 7.0 | 12.4 | DIN 508 / GN505 |
| M10 | 12 | 14.0 | 14.0 | 8.0 | 12.4 | DIN 508 / GN505 |
| M10 | 14 | 16.0 | 14.0 | 8.0 | 14.4 | DIN 508 / GN505 |
| M12 | 14 | 16.0 | 17.0 | 10.0 | 14.4 | DIN 508 / GN505 |
| M12 | 18 | 20.0 | 17.0 | 10.0 | 18.4 | DIN 508 / GN505 |
| M16 | 18 | 20.0 | 20.0 | 12.0 | 18.4 | DIN 508 / GN505 |
| M16 | 22 | 25.0 | 20.0 | 12.0 | 22.4 | DIN 508 / GN505 |
| M20 | 22 | 25.0 | 25.0 | 15.0 | 22.4 | DIN 508 / GN505 |
| M20 | 28 | 32.0 | 25.0 | 15.0 | 28.4 | DIN 508 / GN505 |
| M24 | 28 | 32.0 | 30.0 | 18.0 | 28.4 | DIN 508 / GN505 |

Product catalog

## Related T-Slot Nuts products

[![M4 M5 M6 M8 T-Nut Round Roll T Slot Spring Nut 4040/4545 Series Nickel Plated](https://img.engineeringhardware.com/M4-M5-M6-M8-T-Nut-Round-Roll-T-Slot-Spring-Nut-4040-4545-Series-Nickel-Plated.webp)](https://engineeringhardware.com/product/m4-m5-m6-m8-t-nut-round-roll-t-slot-spring-nut-4040-4545-series-nickel-plated/)

T-Nuts, Slot Nuts & Channel Spring Nuts

### [M4 M5 M6 M8 T-Nut Round Roll T Slot Spring Nut 4040/4545 Series Nickel Plated](https://engineeringhardware.com/product/m4-m5-m6-m8-t-nut-round-roll-t-slot-spring-nut-4040-4545-series-nickel-plated/)

T Head · DIN, ANSI, GB, JIS, GOST, BSW

**US$0.012 – 0.06**MOQ 1,000 pieces

[![Profile T Spring Nut for Aluminum Profile Leaf Spring Nut](https://img.engineeringhardware.com/Profile-T-Spring-Nut-for-Aluminum-Profile-Leaf-Spring-Nut-5.webp)](https://engineeringhardware.com/product/profile-t-spring-nut-for-aluminum-profile-leaf-spring-nut-5/)

T-Nuts, Slot Nuts & Channel Spring Nuts

### [Profile T Spring Nut for Aluminum Profile Leaf Spring Nut](https://engineeringhardware.com/product/profile-t-spring-nut-for-aluminum-profile-leaf-spring-nut-5/)

Hexagon Head · OEM According to Customer's Requirement

**US$0.072**MOQ 6,000 pieces

[![2024 Hot Sale T-Block /T-Nuts for Lathe Hydraulic Power Chucks 10inch](https://img.engineeringhardware.com/2024-Hot-Sale-T-Block-T-Nuts-for-Lathe-Hydraulic-Power-Chucks-10inch.webp)](https://engineeringhardware.com/product/2024-hot-sale-t-block-t-nuts-for-lathe-hydraulic-power-chucks-10inch/)

T-Nuts, Slot Nuts & Channel Spring Nuts

### [2024 Hot Sale T-Block /T-Nuts for Lathe Hydraulic Power Chucks 10inch](https://engineeringhardware.com/product/2024-hot-sale-t-block-t-nuts-for-lathe-hydraulic-power-chucks-10inch/)

Thru · 42crmov

**US$12.00 – 14.40**MOQ 1 set

[![China Manufacturer RoHS ODM OEM 5448 M8 40180 T Nuts with 5 Hole for 40 Series Aluminum Extrusion](https://img.engineeringhardware.com/China-Manufacturer-RoHS-ODM-OEM-5448-M8-40180-T-Nuts-with-5-Hole-for-40-Series-Aluminum-Extrusion.webp)](https://engineeringhardware.com/product/china-manufacturer-rohs-odm-oem-5448-m8-40180-t-nuts-with-5-hole-for-40-series/)

T-Nuts, Slot Nuts & Channel Spring Nuts

### [China Manufacturer RoHS ODM OEM 5448 M8 40180 T Nuts with 5 Hole for 40 Series Aluminum Extrusion](https://engineeringhardware.com/product/china-manufacturer-rohs-odm-oem-5448-m8-40180-t-nuts-with-5-hole-for-40-series/)

T Head · Carbon Steel

**US$0.59 – 0.69**MOQ 1 piece

[![Malaxy A2 Stainless Steel Spring Nut DIN985 Galvanized Tinnerman Nut Self Locking Sheet Metal Nut for Panel Mounting Spring Nut](https://img.engineeringhardware.com/Malaxy-A2-Stainless-Steel-Spring-Nut-DIN985-Galvanized-Tinnerman-Nut-Self-Locking-Sheet-Metal-Nut-for-Panel-Mounting-Spring-Nut.webp)](https://engineeringhardware.com/product/malaxy-a2-stainless-steel-spring-nut-din985-galvanized-tinnerman-nut-self-locking/)

T-Nuts, Slot Nuts & Channel Spring Nuts

### [Malaxy A2 Stainless Steel Spring Nut DIN985 Galvanized Tinnerman Nut Self Locking Sheet Metal Nut for Panel Mounting Spring Nut](https://engineeringhardware.com/product/malaxy-a2-stainless-steel-spring-nut-din985-galvanized-tinnerman-nut-self-locking/)

Hexagon Head · DIN, ANSI, GB, JIS, GOST, BSW

**US$0.006 – 0.024**MOQ 10,000 pieces

[![Tuercas Con Resorte Channel Nuts with Spring Strut Channel Fitting Support Fittings](https://img.engineeringhardware.com/Tuercas-Con-Resorte-Channel-Nuts-with-Spring-Strut-Channel-Fitting-Support-Fittings.webp)](https://engineeringhardware.com/product/tuercas-con-resorte-channel-nuts-with-spring-strut-channel-fitting-support-fittings/)

T-Nuts, Slot Nuts & Channel Spring Nuts

### [Tuercas Con Resorte Channel Nuts with Spring Strut Channel Fitting Support Fittings](https://engineeringhardware.com/product/tuercas-con-resorte-channel-nuts-with-spring-strut-channel-fitting-support-fittings/)

with Spring · DIN, ANSI, GB

**US$0.06 – 1.80**MOQ 100 pieces

[View all T-Nuts, Slot Nuts & Channel Spring Nuts →](https://engineeringhardware.com/fastener-products/nuts/t-nuts-slot-nuts-channel-spring-nuts/) [Full product catalog](https://engineeringhardware.com/products/)

## Materials & Grades

Select a material class to see the grades we supply it in. Each designation is listed with its ISO/EN, AISI/SAE, JIS and GB equivalents.

Stainless Steel38 Carbon Steel66 Alloy Steel41 Bearing Steel5 Spring Steel25 Aluminum and Aluminum Alloys21 Brass17 Bronze11 Copper8 Titanium and Titanium Alloys18 Nickel and Nickel Alloys22 Iron-Nickel and High-Temperature Alloys10 Tool Steel and Specialty Hardened Steel9 Structural and Construction Steel9

### Stainless Steel

#### Austenitic Stainless Steel

- A1 AISI 303 · SAE 303 · SUS303 · EN 1.4305 · X8CrNiS18-9
- A2 AISI 304 · SAE 304 · SUS304 · EN 1.4301 · X5CrNi18-10 · 06Cr19Ni10
- 304L AISI 304L · SUS304L · EN 1.4307 · X2CrNi18-9 · 022Cr19Ni10
- 302 AISI 302 · SUS302 · EN 1.4310
- 305 AISI 305 · SUS305 · EN 1.4303
- A4 AISI 316 · SAE 316 · SUS316 · EN 1.4401 · X5CrNiMo17-12-2 · 06Cr17Ni12Mo2
- 316L AISI 316L · SUS316L · EN 1.4404 · X2CrNiMo17-12-2 · 022Cr17Ni12Mo2
- 321 AISI 321 · SUS321 · EN 1.4541 · X6CrNiTi18-10
- 310 / 310S AISI 310 · AISI 310S · SUS310S · EN 1.4845
- 302HQ AISI 302HQ
- A3
- A5
- 347 AISI 347 · SUS347 · EN 1.4550 · X6CrNiNb18-10
- 309 / 309S AISI 309 · AISI 309S · SUS309S

#### Martensitic Stainless Steel

- AISI 410 SUS410 · EN 1.4006 · X12Cr13 · 12Cr13
- AISI 420 SUS420J1 · SUS420J2 · EN 1.4021 · EN 1.4028 · 20Cr13 · 30Cr13
- AISI 431 SUS431 · EN 1.4057 · X17CrNi16-2
- C1
- C3
- C4
- AISI 440A
- AISI 440B
- AISI 440C SUS440C · EN 1.4125

#### Ferritic Stainless Steel

- AISI 430 SUS430 · EN 1.4016 · X6Cr17 · 10Cr17
- F1
- AISI 434
- AISI 444

#### Precipitation-Hardening Stainless Steel

- 17-4 PH AISI 630 · UNS S17400 · SUS630 · EN 1.4542 · X5CrNiCuNb16-4
- 15-5 PH UNS S15500
- 17-7 PH UNS S17700

#### Duplex and Super Duplex Stainless Steel

- Duplex 2205 UNS S31803 · UNS S32205 · EN 1.4462
- Super Duplex 2507 UNS S32750 · EN 1.4410
- D2
- D4
- D6
- D8
- Lean Duplex 2101 UNS S32101
- Super Duplex S32760 UNS S32760 · EN 1.4501

### Carbon Steel

#### Low-Carbon Steel

- SAE 1006
- SAE 1008
- SAE 1010
- SAE 1018
- SAE 1020
- Q195
- Q235
- SAE 1012
- SAE 1015
- Q215
- ML08
- ML08Al
- ML10
- ML15
- ML20
- SWRCH6A
- SWRCH8A
- SWRCH10A
- SWRCH12A
- SWRCH15A
- SWRCH18A

#### Medium-Carbon Steel

- SAE 1035
- SAE 1045
- S45C
- C45
- SAE 1030
- SAE 1040
- SAE 1050
- 30
- 35
- 40
- 45
- 50
- S35C
- S40C
- S50C
- C35
- C40

#### High-Carbon Steel

- SAE 1060
- SAE 1070
- 65Mn
- SAE 1065
- SAE 1075
- SAE 1080
- SAE 1085
- SAE 1090
- SAE 1095
- 60
- 65
- 70
- 75
- 80
- 85

#### Cold-Heading Steel

- SWRCH22A
- 10B21
- SWRCH22K
- SWRCH25K
- SWRCH30K
- SWRCH35K
- SWRCH40K
- ML20Mn
- ML25
- ML30
- ML35
- ML40
- 15B25

### Alloy Steel

#### Chromium Steel

- 40Cr
- 45Cr
- AISI 5140
- SAE 5140
- AISI 5120
- SAE 5120
- SCr420
- SCr440

#### Chromium-Molybdenum Steel

- 35CrMo
- 42CrMo
- AISI 4140
- SCM435
- SCM440
- 42CrMo4
- 30CrMo
- AISI 4130
- SAE 4130
- SAE 4140
- AISI 4142
- AISI 4145
- SCM415
- SCM420
- SCM445
- EN 1.7220
- EN 1.7225
- 25CrMo4
- 34CrMo4

#### Nickel-Chromium-Molybdenum Steel

- AISI 4340
- SAE 4340
- 40CrNiMo
- SNCM439
- EN 1.6511
- 36CrNiMo4

#### Boron Alloy Steel

- 10B22
- 10B21
- 15B21
- 15B25
- 20MnTiB
- 20Mn2B
- 35VB
- 40MnB

### Bearing Steel

#### Bearing Steel

- GCr15
- AISI 52100 SAE 52100 · UNS G52986
- SUJ2
- 100Cr6 EN 1.3505
- GCr15SiMn

### Spring Steel

#### Carbon Spring Steel

- SAE 1065
- SAE 1070
- SAE 1075
- SAE 1080
- SAE 1095
- 65
- 70
- 75
- 80
- 65Mn

#### Silicon-Manganese Spring Steel

- 60Si2Mn
- 60Si2MnA
- SUP6
- SUP7

#### Chromium-Vanadium Spring Steel

- 50CrVA
- SAE 6150
- AISI 6150
- SUP10

#### Stainless Spring Steel

- AISI 301
- SUS301
- EN 1.4310
- AISI 302
- AISI 304
- AISI 316
- 17-7 PH

### Aluminum and Aluminum Alloys

#### Commercially Pure Aluminum

- 1050
- 1060
- 1070
- 1100

#### 2xxx Series Aluminum

- 2024
- 2011
- 2014
- 2017

#### 5xxx Series Aluminum

- 5052
- 5083
- 5754

#### 6xxx Series Aluminum

- 6061
- 6061-T6
- 6063
- 6082
- 6082-T6

#### 7xxx Series Aluminum

- 7075
- 7075-T6
- 7005
- 7050
- 7075-T73

### Brass

#### Free-Cutting Brass

- C36000
- H62
- HPb59-1
- C3601
- C3602
- C3604
- CuZn36Pb3
- CuZn39Pb3
- EN CW614N
- EN CW617N
- H65

#### Lead-Free Brass

- C69300
- C27450
- CW510L
- CW511L

#### Naval Brass

- C46400
- CuZn39Sn1

### Bronze

#### Silicon Bronze

- C65500
- C65100
- C65600

#### Phosphor Bronze

- C51000
- C52100
- CuSn6
- CuSn8

#### Aluminum Bronze

- C95400
- C95500
- C63000
- CuAl10Ni5Fe4

### Copper

#### Copper

- C11000
- T2
- C10100
- C10200
- C12200
- T1
- TU1
- TU2

### Titanium and Titanium Alloys

#### Commercially Pure Titanium

- Grade 2
- Grade 1
- Grade 3
- Grade 4
- TA1
- TA2
- TA3

#### Alpha-Beta Titanium Alloys

- Grade 5
- Ti-6Al-4V
- TC4
- UNS R56400

#### Low-Interstitial Grade

- Grade 23
- Ti-6Al-4V ELI
- UNS R56407

#### Other Titanium Fastener Alloys

- Ti-6Al-6V-2Sn
- Ti-6Al-2Sn-4Zr-2Mo
- Beta-C titanium
- Ti-10V-2Fe-3Al

### Nickel and Nickel Alloys

#### Commercially Pure Nickel

- Nickel 200
- UNS N02200
- Nickel 201
- UNS N02201

#### Inconel Alloys

- Inconel 625 UNS N06625
- Inconel 718 UNS N07718
- Inconel 600 UNS N06600
- Inconel 601 UNS N06601
- Inconel 686 UNS N06686
- Inconel X-750 UNS N07750

#### Monel Alloys

- Monel 400 UNS N04400
- Monel K-500 UNS N05500

#### Hastelloy Alloys

- Hastelloy C-276 UNS N10276
- Hastelloy C-22 UNS N06022
- Hastelloy B-2 UNS N10665
- Hastelloy B-3 UNS N10675
- Hastelloy X UNS N06002

#### Other Nickel Alloys

- Alloy 20 UNS N08020
- Alloy 625
- Alloy 718
- Alloy 825 UNS N08825
- Alloy 925 UNS N09925

### Iron-Nickel and High-Temperature Alloys

#### A286

- A-286
- UNS S66286
- EN 1.4980

#### Invar

- Invar 36
- Alloy 36
- UNS K93600
- FeNi36

#### Alloy 42

- Alloy 42
- UNS K94100
- FeNi42

### Tool Steel and Specialty Hardened Steel

#### Tool Steel and Specialty Hardened Steel

- AISI D2
- AISI H13
- SKD11
- Cr12MoV
- AISI O1
- AISI A2
- AISI S7
- SKD61
- 9CrSi

### Structural and Construction Steel

#### Structural and Construction Steel

- ASTM A36
- Q235B
- Q355B
- S355JR
- Q235C
- Q355C
- S235JR
- S275JR
- S355J2

## Applications & Industries for M24 T-Slot Nuts

T-Slot Nuts are bought for a small number of well-defined jobs. These are the ones we ship them for. Stocked from M5 to M24.

### Industries that specify T-Slot Nuts

- **Automation framing:** Profile systems and guarding.
- **Machine shops:** Clamping to milling and drilling tables.
- **Automotive & transport:** Vibration-prone joints where the locking type is specified on the drawing.
- **Maintenance & MRO:** Replacements matched to the existing bolt class, thread and finish.
- **Building services:** Threaded rod, channel and suspension assemblies.
- **Machine building & OEM:** The clamping counter-face on studs and bolts throughout an assembly.

### Typical applications

- clamp sets and fixture plates
- clamping through a machine table slot
- completing a bolted joint on a stud, rod or bolt
- locking an adjustment so it cannot drift
- joints re-torqued at a service interval

### Service conditions to specify against

- **Marine and coastal:** Available in A4 (316) stainless for chloride exposure — coastal structures, pool halls, water treatment and deck hardware, where A2 will eventually pit.
- **High load:** Supplied in ISO 898-1 property classes, so the joint can be designed to a stated proof load and tightened to a calculated torque rather than by feel.
- **Match the class:** A nut below the bolt property class strips before the bolt reaches its own limit — pair class 8 nuts with 8.8 bolts, class 10 with 10.9.

[Full application guide: where T-Slot Nuts are used, how to specify them, and the cases they are wrong for](https://engineeringhardware.com/applications/t-slot-nuts/)

Inside the plant

## Manufactured in our own plant

This part is cold-formed, threaded, heat-treated and finished in-house. The stages below are where its class and finish are actually decided.

1. ![Wire rod feeding into a cold heading machine](https://engineeringhardware.com/wp-content/uploads/2026/08/09-wire-rod-feed-cold-heading-machine.webp) 01 **Cold heading** Wire rod is drawn to size and cold-formed into blanks. Forming rather than cutting keeps the grain flow continuous around the head, which is where a bolt is most likely to fail. Head dimensions and under-head radius checked at set-up and per shift.
2. ![Thread rolling machine producing bolt threads](https://engineeringhardware.com/wp-content/uploads/2026/08/03-thread-rolling-machine-bolt-production.webp) 02 **Thread rolling** Threads are rolled between hardened dies rather than cut. Rolled threads are stronger in fatigue than cut threads and hold pitch and flank angle far more consistently across a batch. Go / no-go ring gauges to ISO 965 tolerance class 6g.
3. ![Baskets of bolts staged for heat treatment](https://engineeringhardware.com/wp-content/uploads/2026/08/05-heat-treatment-baskets-black-bolts.webp) 03 **Heat treatment** Quench-and-temper brings carbon and alloy steel to the property class ordered — 8.8, 10.9 or 12.9 — with the furnace charge tracked so a finished lot can be traced back to it. Core hardness and tensile tested per lot to ISO 898-1.
4. ![Zinc plated bolts in a treatment basket](https://engineeringhardware.com/wp-content/uploads/2026/08/23-zinc-plated-bolts-treatment-basket.webp) 04 **Surface treatment** Zinc, zinc-nickel, hot-dip galvanizing, black oxide, phosphate and Dacromet, selected against the service environment rather than against the price list. Coating thickness and neutral salt spray hours to ISO 9227.

## Frequently Asked Questions

### What grip range is typical for M24 structural bolts?

Grip ranges are highly application-dependent at M24. As a guide, choose a length that gives at least 1× the thread diameter engagement in the nut plus 2–3 thread pitches projecting.

### What is the height of an M24 nut?

The nominal height of a style-1 ISO 4032 M24 nut is in the spec table on this page. Style-2 (thick) is approximately 1.1× this height; thin (ISO 4035 / DIN 439) is approximately 0.5×.

### What is the coarse-thread pitch of M24 for T-Slot Nuts?

For M24 the standard coarse pitch is 3 mm — this is the value used for T-Slot Nuts.

### What clearance and tapping drill suit M24?

Use a 26 mm clearance hole (ISO 273 medium) for through-fixing, or a 21 mm tapping drill for a coarse M24 thread.

### How do I request a quotation?

Use the technical drawing on this page to pick the exact configuration, then submit it with the quote form. We respond within one business day.

## Related Pages

[View the full T-Slot Nuts page](https://engineeringhardware.com/fastener/t-slot-nuts/)

### More T-Slot Nuts Guides