M6 Slotted Headless Screws with Shank are manufactured to ISO 2342 with a coarse thread pitch of 1 mm. This page lists the controlling dimensions for the M6 size — head geometry, width across flats, matching spanner size — together with the clearance hole, tapping drill and tightening torque used at assembly.
M6 Dimensional Row (ISO 2342)
| Size | Pitch P (mm) | b (mm) | d_s_min (mm) | d_s_max (mm) | n_nom (mm) | n_min (mm) | n_max (mm) | t_min (mm) | t_max (mm) | x_max (mm) | Length range l (mm) | Reference standard |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| M6 | 1 | 7.2 | 5.82 | 6 | 1 | 1.06 | 1.2 | 2.5 | 2.9 | 2.5 | 12~25 | ISO 2342 |
Spanner & Drive for M6 Slotted Headless Screws with Shank
The hex socket for M6 Slotted Headless Screws with Shank is shown in the spec table — use the matching Allen / hex key (an ISO 2936 hex key set covers the full range). For a one-off, a T-handle key and a calibrated arm will do. For a batch, the only way to get the same preload twice is a torque-controlled driver.
Hole Sizes for M6
| Coarse-thread pitch (ISO 724) | 1 mm |
|---|---|
| Through-hole / clearance (ISO 273 medium) | 6.6 mm |
| Tapping drill, coarse thread | 5 mm |
Tightening Torque for M6
| Class 8.8 (dry, ~µ 0.125) | ≈ 10 Nm |
|---|---|
| Class 10.9 (dry, ~µ 0.125) | ≈ 15 Nm |
| Class 12.9 (dry, ~µ 0.125) | ≈ 17 Nm |
Indicative dry-joint values. Lubrication can lower the required torque by 15–25%. Always confirm against the joint design, especially when going up a strength class.
Proof Load & Strength for M6
Set screws are rated to ISO 898-5 by hardness, because they work in compression against a shaft rather than in tension. ISO 898-1 excludes them, and a set screw has no head to preload against, so neither a property class nor a preload torque applies. Seating torque depends on the point form and the shaft material.
M6 Slotted Headless Screws with Shank Weight
A steel M6 slotted headless screws with shank at the listed 1,225 mm length weighs approximately 272 g each — about 272 kg per 1,000 pieces. Stainless A2/A4 weighs roughly the same (density 7.9–8.0 g/cm³).
Actual weight varies slightly with head form, thread and finish; use this figure for freight estimation only.
Mating Parts for M6
For M6, pair with a M6 hex nut (ISO 4032 / DIN 934) and, where used, a M6 flat washer (ISO 7089 / DIN 125A) under the head and under the nut.
When to Step Up or Down from M6
When the joint preload approaches the proof load of M6 class 8.8, step up to M8 class 8.8 (or move to M6 class 10.9). When the joint is over-specified, M5 often saves weight and cost without losing the safety margin.
Custom manufacturing · Made to drawing
Need slotted headless screws with shank in a size this table does not list?
This page covers M6 slotted headless screws with shank. Head form and drive can be specified to the assembly rather than to a standard: a larger bearing face, a security drive, or a socket sized for the tool already on the bench. Made by cold heading or warm forging.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
