---
title: "M8 Channel (Strut) Nuts with Spring Dimensions"
description: "M8 Channel (Strut) Nuts with Spring: nut height 13 mm, coarse thread pitch 1.25 mm. Tightening torque 24 Nm at class 8.8."
url: https://engineeringhardware.com/guide/size/m8-channel-strut-nuts/
source: Engineering Hardware & Fasteners
---

# M8 Channel (Strut) Nuts with Spring Dimensions

Nuts · Trade series (strut channel nut)

Controlling dimensions to Trade series (strut channel nut), with spanner or drive size and tightening torque.

M8 Channel (Strut) Nuts with Spring dimensions to Trade series (strut channel nut): nut height 13 mm, coarse thread pitch 1.25 mm. Tighten to approximately 24 Nm at property class 8.8 in a dry, as-supplied condition.

- **Nut height:** 13 mm
- **Coarse thread pitch:** 1.25 mm
- **Tightening torque (class 8.8):** 24 Nm

Figures are nominal values from the governing standard. Confirm against the tolerance class for your application before machining or ordering.

![M8 Channel (Strut) Nuts with Spring Dimensions reference image](https://engineeringhardware.com/wp-content/uploads/2026/09/Strut-Channel-Spring-Nuts.webp)

M8 Channel (Strut) Nuts with Spring are manufactured to Trade series (strut channel nut). This page lists the controlling dimensions for the M8 size together with the drive and the installation notes for this type.

Values are taken from the governing standard rather than from a general machine-thread table, because this type is not selected on one.

## M8 Dimensional Row (Trade series (strut channel nut))

| Thread size | For channel width (mm) | Nut width (mm) | Nut height (mm) | Spring | Slot engagement | Material | Finish |
| --- | --- | --- | --- | --- | --- | --- | --- |
| M8 | 41 | 41 | 13 | Long spring | Grooved both ends | Steel | Zinc plated |

## Spanner & Drive for M8 Channel (Strut) Nuts with Spring

Drive geometry for M8 Channel (Strut) Nuts with Spring is given by the row above; match the tool to the listed values.

## Tightening Torque for M8

| Class 8.8 (dry, ~µ 0.125) | ≈ 24 Nm |
| --- | --- |
| Class 10.9 (dry, ~µ 0.125) | ≈ 36 Nm |
| Class 12.9 (dry, ~µ 0.125) | ≈ 42 Nm |

Indicative dry-joint values. Lubrication can lower the required torque by 15–25%. Always confirm against the joint design, especially when going up a strength class.

## Proof Load & Strength for M8

Nuts are graded to ISO 898-2 by the proof load the nut itself will hold (classes 04, 05, 5, 6, 8, 10 and 12), not by the 8.8 / 10.9 / 12.9 scale used for bolts. A class-8 nut is the correct mate for a class-8.8 bolt, and the joint is designed on the bolt, so no bolt-tension figure is quoted here.

## Mating Parts for M8

Pair M8 with the matching M8 bolt or screw, plus a M8 flat washer where required to distribute load on softer materials.

## When to Step Up or Down from M8

When the joint preload approaches the proof load of M8 class 8.8, step up to M10 class 8.8 (or move to M8 class 10.9). When the joint is over-specified, M6 often saves weight and cost without losing the safety margin.

Custom manufacturing · Made to drawing

## Need channel (strut) nuts with spring in a size this table does not list?

This page covers M8 channel (strut) nuts with spring. Locking method is specifiable independently of the rest: nylon insert, all-metal deformed thread, serrated flange, or none. Made by cold heading or tapping.

Minimum order from 2,000 pieces; samples within 7 days of drawing approval.

[Custom nut manufacturing](https://engineeringhardware.com/custom/nuts/)[Send a drawing](https://engineeringhardware.com/custom/nuts/#rfq)

## Technical Drawing

Dimensioned line drawing of M8 Channel (Strut) Nuts with Spring to Trade series (strut channel nut). Side view and top view, drawn to the dimensions in the table below and redrawn for any size selected.

- **For channel width (mm):** 41
- **Nut width (mm):** 41
- **Nut height (mm):** 13
- **Spring:** Long spring
- **Slot engagement:** Grooved both ends
- **Material:** Steel
- **Finish:** Zinc plated

## Dimensions & Specifications (Trade series (strut channel nut))

| Thread size | For channel width (mm) | Nut width (mm) | Nut height (mm) | Spring | Slot engagement | Material | Finish |
| --- | --- | --- | --- | --- | --- | --- | --- |
| M6 | 41 | 41 | 13 | Long spring | Grooved both ends | Steel | Zinc plated |
| M8 | 41 | 41 | 13 | Long spring | Grooved both ends | Steel | Zinc plated |
| M10 | 41 | 41 | 13 | Long spring | Grooved both ends | Steel | Hot-dip galvanised |
| M12 | 41 | 41 | 13 | Long spring | Grooved both ends | Steel | Hot-dip galvanised |
| M8 | 21 | 21 | 9 | Short spring | Grooved both ends | Steel | Zinc plated |
| M10 | 41 | 41 | 13 | No spring | Grooved both ends | A4 stainless | Passivated |

Product catalog

## Related Channel (Strut) Nuts products

[![Wear Resistant C3604 Hot Melt Nut for Embedded by Hot Melting or Ultrasonic Method](https://img.engineeringhardware.com/Wear-Resistant-C3604-Hot-Melt-Nut-for-Embedded-by-Hot-Melting-or-Ultrasonic-Method.webp)](https://engineeringhardware.com/product/wear-resistant-c3604-hot-melt-nut-for-embedded-by-hot-melting-or-ultrasonic-method/)

T-Nuts, Slot Nuts & Channel Spring Nuts

### [Wear Resistant C3604 Hot Melt Nut for Embedded by Hot Melting or Ultrasonic Method](https://engineeringhardware.com/product/wear-resistant-c3604-hot-melt-nut-for-embedded-by-hot-melting-or-ultrasonic-method/)

Round Head · ISO9001/RoHS/Reach

**US$0.77 – 0.96**MOQ 100 pieces

[![Aluminum Extrusion Profile Accessories, T-Nuts, Spring Nuts, Serrated Hex Flange Nuts](https://img.engineeringhardware.com/Aluminum-Extrusion-Profile-Accessories-T-Nuts-Spring-Nuts-Serrated-Hex-Flange-Nuts.webp)](https://engineeringhardware.com/product/aluminum-extrusion-profile-accessories-t-nuts-spring-nuts-serrated-hex-flange-nuts/)

T-Nuts, Slot Nuts & Channel Spring Nuts

### [Aluminum Extrusion Profile Accessories, T-Nuts, Spring Nuts, Serrated Hex Flange Nuts](https://engineeringhardware.com/product/aluminum-extrusion-profile-accessories-t-nuts-spring-nuts-serrated-hex-flange-nuts/)

Ss/Steel · Hex

**US$0.012 – 0.018**MOQ 300 mpcs

[![304 Stainless Steel Hex Thin Nut Fine-Thread Imperial Pipe & Faucet Nut Lock-Tight](https://img.engineeringhardware.com/304-Stainless-Steel-Hex-Thin-Nut-Fine-Thread-Imperial-Pipe-Faucet-Nut-Lock-Tight.webp)](https://engineeringhardware.com/product/304-stainless-steel-hex-thin-nut-fine-thread-imperial-pipe-faucet-nut-lock-tight/)

T-Nuts, Slot Nuts & Channel Spring Nuts

### [304 Stainless Steel Hex Thin Nut Fine-Thread Imperial Pipe & Faucet Nut Lock-Tight](https://engineeringhardware.com/product/304-stainless-steel-hex-thin-nut-fine-thread-imperial-pipe-faucet-nut-lock-tight/)

Hexagon Head · DIN, ANSI, GB, JIS, BSW

**US$816.00 – 1,440**MOQ 1 piece

[![Galvanized Extended Hexagonal Nut/Extended Round Joint Nut/Threaded Connection Nut M6-M20](https://img.engineeringhardware.com/Galvanized-Extended-Hexagonal-Nut-Extended-Round-Joint-Nut-Threaded-Connection-Nut-M6-M20.webp)](https://engineeringhardware.com/product/galvanized-extended-hexagonal-nut-extended-round-joint-nut-threaded-connection-nut/)

T-Nuts, Slot Nuts & Channel Spring Nuts

### [Galvanized Extended Hexagonal Nut/Extended Round Joint Nut/Threaded Connection Nut M6-M20](https://engineeringhardware.com/product/galvanized-extended-hexagonal-nut-extended-round-joint-nut-threaded-connection-nut/)

Hexagon Head · DIN, ANSI, GB, JIS, BSW, ASME

**US$0.12 – 0.60**MOQ 1 piece

[![Factory Price High Strength Yjt 3023 Yjt 3002 DIN 1624 M4-M48 Carbon Steel Zinc Plated Claw Nut Cl4/8/10 Tee Nuts with Pronge](https://img.engineeringhardware.com/Factory-Price-High-Strength-Yjt-3023-Yjt-3002-DIN-1624-M4-M48-Carbon-Steel-Zinc-Plated-Claw-Nut-Cl4-8-10-Tee-Nuts-with-Pronge.webp)](https://engineeringhardware.com/product/factory-price-high-strength-yjt-3023-yjt-3002-din-1624-m4-m48-carbon-steel-zinc/)

T-Nuts, Slot Nuts & Channel Spring Nuts

### [Factory Price High Strength Yjt 3023 Yjt 3002 DIN 1624 M4-M48 Carbon Steel Zinc Plated Claw Nut Cl4/8/10 Tee Nuts with Pronge](https://engineeringhardware.com/product/factory-price-high-strength-yjt-3023-yjt-3002-din-1624-m4-m48-carbon-steel-zinc/)

Tee Nuts with Pronge · DIN, ANSI, GB, JIS, GOST, BSW, ASME

**US$0.012 – 0.048**MOQ 1,000 pieces

[![Stainless Steel T-Slot Nuts 3030 M6 Half Round Flat Base Roll in Ball T Nut Spring Ball Nut](https://img.engineeringhardware.com/Stainless-Steel-T-Slot-Nuts-3030-M6-Half-Round-Flat-Base-Roll-in-Ball-T-Nut-Spring-Ball-Nut.webp)](https://engineeringhardware.com/product/stainless-steel-t-slot-nuts-3030-m6-half-round-flat-base-roll-in-ball-t-nut-spring/)

T-Nuts, Slot Nuts & Channel Spring Nuts

### [Stainless Steel T-Slot Nuts 3030 M6 Half Round Flat Base Roll in Ball T Nut Spring Ball Nut](https://engineeringhardware.com/product/stainless-steel-t-slot-nuts-3030-m6-half-round-flat-base-roll-in-ball-t-nut-spring/)

Stainlesss Steel Carbon Steel B7 · ISO, GS, RoHS, CE

**US$0.036**MOQ 1,000 pieces

[View all T-Nuts, Slot Nuts & Channel Spring Nuts →](https://engineeringhardware.com/fastener-products/nuts/t-nuts-slot-nuts-channel-spring-nuts/) [Full product catalog](https://engineeringhardware.com/products/)

## Materials & Grades

Select a material class to see the grades we supply it in. Each designation is listed with its ISO/EN, AISI/SAE, JIS and GB equivalents.

Stainless Steel38 Carbon Steel66 Alloy Steel41 Bearing Steel5 Spring Steel25 Aluminum and Aluminum Alloys21 Brass17 Bronze11 Copper8 Titanium and Titanium Alloys18 Nickel and Nickel Alloys22 Iron-Nickel and High-Temperature Alloys10 Tool Steel and Specialty Hardened Steel9 Structural and Construction Steel9

### Stainless Steel

#### Austenitic Stainless Steel

- A1 AISI 303 · SAE 303 · SUS303 · EN 1.4305 · X8CrNiS18-9
- A2 AISI 304 · SAE 304 · SUS304 · EN 1.4301 · X5CrNi18-10 · 06Cr19Ni10
- 304L AISI 304L · SUS304L · EN 1.4307 · X2CrNi18-9 · 022Cr19Ni10
- 302 AISI 302 · SUS302 · EN 1.4310
- 305 AISI 305 · SUS305 · EN 1.4303
- A4 AISI 316 · SAE 316 · SUS316 · EN 1.4401 · X5CrNiMo17-12-2 · 06Cr17Ni12Mo2
- 316L AISI 316L · SUS316L · EN 1.4404 · X2CrNiMo17-12-2 · 022Cr17Ni12Mo2
- 321 AISI 321 · SUS321 · EN 1.4541 · X6CrNiTi18-10
- 310 / 310S AISI 310 · AISI 310S · SUS310S · EN 1.4845
- 302HQ AISI 302HQ
- A3
- A5
- 347 AISI 347 · SUS347 · EN 1.4550 · X6CrNiNb18-10
- 309 / 309S AISI 309 · AISI 309S · SUS309S

#### Martensitic Stainless Steel

- AISI 410 SUS410 · EN 1.4006 · X12Cr13 · 12Cr13
- AISI 420 SUS420J1 · SUS420J2 · EN 1.4021 · EN 1.4028 · 20Cr13 · 30Cr13
- AISI 431 SUS431 · EN 1.4057 · X17CrNi16-2
- C1
- C3
- C4
- AISI 440A
- AISI 440B
- AISI 440C SUS440C · EN 1.4125

#### Ferritic Stainless Steel

- AISI 430 SUS430 · EN 1.4016 · X6Cr17 · 10Cr17
- F1
- AISI 434
- AISI 444

#### Precipitation-Hardening Stainless Steel

- 17-4 PH AISI 630 · UNS S17400 · SUS630 · EN 1.4542 · X5CrNiCuNb16-4
- 15-5 PH UNS S15500
- 17-7 PH UNS S17700

#### Duplex and Super Duplex Stainless Steel

- Duplex 2205 UNS S31803 · UNS S32205 · EN 1.4462
- Super Duplex 2507 UNS S32750 · EN 1.4410
- D2
- D4
- D6
- D8
- Lean Duplex 2101 UNS S32101
- Super Duplex S32760 UNS S32760 · EN 1.4501

### Carbon Steel

#### Low-Carbon Steel

- SAE 1006
- SAE 1008
- SAE 1010
- SAE 1018
- SAE 1020
- Q195
- Q235
- SAE 1012
- SAE 1015
- Q215
- ML08
- ML08Al
- ML10
- ML15
- ML20
- SWRCH6A
- SWRCH8A
- SWRCH10A
- SWRCH12A
- SWRCH15A
- SWRCH18A

#### Medium-Carbon Steel

- SAE 1035
- SAE 1045
- S45C
- C45
- SAE 1030
- SAE 1040
- SAE 1050
- 30
- 35
- 40
- 45
- 50
- S35C
- S40C
- S50C
- C35
- C40

#### High-Carbon Steel

- SAE 1060
- SAE 1070
- 65Mn
- SAE 1065
- SAE 1075
- SAE 1080
- SAE 1085
- SAE 1090
- SAE 1095
- 60
- 65
- 70
- 75
- 80
- 85

#### Cold-Heading Steel

- SWRCH22A
- 10B21
- SWRCH22K
- SWRCH25K
- SWRCH30K
- SWRCH35K
- SWRCH40K
- ML20Mn
- ML25
- ML30
- ML35
- ML40
- 15B25

### Alloy Steel

#### Chromium Steel

- 40Cr
- 45Cr
- AISI 5140
- SAE 5140
- AISI 5120
- SAE 5120
- SCr420
- SCr440

#### Chromium-Molybdenum Steel

- 35CrMo
- 42CrMo
- AISI 4140
- SCM435
- SCM440
- 42CrMo4
- 30CrMo
- AISI 4130
- SAE 4130
- SAE 4140
- AISI 4142
- AISI 4145
- SCM415
- SCM420
- SCM445
- EN 1.7220
- EN 1.7225
- 25CrMo4
- 34CrMo4

#### Nickel-Chromium-Molybdenum Steel

- AISI 4340
- SAE 4340
- 40CrNiMo
- SNCM439
- EN 1.6511
- 36CrNiMo4

#### Boron Alloy Steel

- 10B22
- 10B21
- 15B21
- 15B25
- 20MnTiB
- 20Mn2B
- 35VB
- 40MnB

### Bearing Steel

#### Bearing Steel

- GCr15
- AISI 52100 SAE 52100 · UNS G52986
- SUJ2
- 100Cr6 EN 1.3505
- GCr15SiMn

### Spring Steel

#### Carbon Spring Steel

- SAE 1065
- SAE 1070
- SAE 1075
- SAE 1080
- SAE 1095
- 65
- 70
- 75
- 80
- 65Mn

#### Silicon-Manganese Spring Steel

- 60Si2Mn
- 60Si2MnA
- SUP6
- SUP7

#### Chromium-Vanadium Spring Steel

- 50CrVA
- SAE 6150
- AISI 6150
- SUP10

#### Stainless Spring Steel

- AISI 301
- SUS301
- EN 1.4310
- AISI 302
- AISI 304
- AISI 316
- 17-7 PH

### Aluminum and Aluminum Alloys

#### Commercially Pure Aluminum

- 1050
- 1060
- 1070
- 1100

#### 2xxx Series Aluminum

- 2024
- 2011
- 2014
- 2017

#### 5xxx Series Aluminum

- 5052
- 5083
- 5754

#### 6xxx Series Aluminum

- 6061
- 6061-T6
- 6063
- 6082
- 6082-T6

#### 7xxx Series Aluminum

- 7075
- 7075-T6
- 7005
- 7050
- 7075-T73

### Brass

#### Free-Cutting Brass

- C36000
- H62
- HPb59-1
- C3601
- C3602
- C3604
- CuZn36Pb3
- CuZn39Pb3
- EN CW614N
- EN CW617N
- H65

#### Lead-Free Brass

- C69300
- C27450
- CW510L
- CW511L

#### Naval Brass

- C46400
- CuZn39Sn1

### Bronze

#### Silicon Bronze

- C65500
- C65100
- C65600

#### Phosphor Bronze

- C51000
- C52100
- CuSn6
- CuSn8

#### Aluminum Bronze

- C95400
- C95500
- C63000
- CuAl10Ni5Fe4

### Copper

#### Copper

- C11000
- T2
- C10100
- C10200
- C12200
- T1
- TU1
- TU2

### Titanium and Titanium Alloys

#### Commercially Pure Titanium

- Grade 2
- Grade 1
- Grade 3
- Grade 4
- TA1
- TA2
- TA3

#### Alpha-Beta Titanium Alloys

- Grade 5
- Ti-6Al-4V
- TC4
- UNS R56400

#### Low-Interstitial Grade

- Grade 23
- Ti-6Al-4V ELI
- UNS R56407

#### Other Titanium Fastener Alloys

- Ti-6Al-6V-2Sn
- Ti-6Al-2Sn-4Zr-2Mo
- Beta-C titanium
- Ti-10V-2Fe-3Al

### Nickel and Nickel Alloys

#### Commercially Pure Nickel

- Nickel 200
- UNS N02200
- Nickel 201
- UNS N02201

#### Inconel Alloys

- Inconel 625 UNS N06625
- Inconel 718 UNS N07718
- Inconel 600 UNS N06600
- Inconel 601 UNS N06601
- Inconel 686 UNS N06686
- Inconel X-750 UNS N07750

#### Monel Alloys

- Monel 400 UNS N04400
- Monel K-500 UNS N05500

#### Hastelloy Alloys

- Hastelloy C-276 UNS N10276
- Hastelloy C-22 UNS N06022
- Hastelloy B-2 UNS N10665
- Hastelloy B-3 UNS N10675
- Hastelloy X UNS N06002

#### Other Nickel Alloys

- Alloy 20 UNS N08020
- Alloy 625
- Alloy 718
- Alloy 825 UNS N08825
- Alloy 925 UNS N09925

### Iron-Nickel and High-Temperature Alloys

#### A286

- A-286
- UNS S66286
- EN 1.4980

#### Invar

- Invar 36
- Alloy 36
- UNS K93600
- FeNi36

#### Alloy 42

- Alloy 42
- UNS K94100
- FeNi42

### Tool Steel and Specialty Hardened Steel

#### Tool Steel and Specialty Hardened Steel

- AISI D2
- AISI H13
- SKD11
- Cr12MoV
- AISI O1
- AISI A2
- AISI S7
- SKD61
- 9CrSi

### Structural and Construction Steel

#### Structural and Construction Steel

- ASTM A36
- Q235B
- Q355B
- S355JR
- Q235C
- Q355C
- S235JR
- S275JR
- S355J2

## Applications & Industries for M8 Channel Nuts with Spring

What Channel Nuts with Spring are specified for, industry by industry. Stocked from M6 to M10.

### Industries that specify Channel Nuts with Spring

- **Building services:** Pipe, duct and tray supports built from strut channel.
- **Plant rooms & racking:** Framework assembled and repositioned in the field.
- **Solar mounting:** Rail systems on roofs and ground mounts.
- **Machine building & OEM:** The clamping counter-face on studs and bolts throughout an assembly.
- **Steel fabrication:** Bolted structural and frame connections.
- **Automotive & transport:** Vibration-prone joints where the locking type is specified on the drawing.

### Typical applications

- fixing into 41 mm and 21 mm strut channel
- the spring holds position while the bolt is started
- ordered by channel size first, thread second
- completing a bolted joint on a stud, rod or bolt
- locking an adjustment so it cannot drift
- joints re-torqued at a service interval

### Service conditions to specify against

- **Marine and coastal:** Available in A4 (316) stainless for chloride exposure — coastal structures, pool halls, water treatment and deck hardware, where A2 will eventually pit.
- **High load:** Supplied in ISO 898-1 property classes, so the joint can be designed to a stated proof load and tightened to a calculated torque rather than by feel.
- **Exterior structural:** Hot-dip galvanised options for external steelwork; allow for the thicker coating in the mating thread.
- **Match the class:** A nut below the bolt property class strips before the bolt reaches its own limit — pair class 8 nuts with 8.8 bolts, class 10 with 10.9.

[Full application guide: where Channel Nuts with Spring are used, how to specify them, and the cases they are wrong for](https://engineeringhardware.com/applications/channel-strut-nuts/)

Inside the plant

## Manufactured in our own plant

This part is cold-formed, threaded, heat-treated and finished in-house. The stages below are where its class and finish are actually decided.

1. ![Wire rod feeding into a cold heading machine](https://engineeringhardware.com/wp-content/uploads/2026/08/09-wire-rod-feed-cold-heading-machine.webp) 01 **Cold heading** Wire rod is drawn to size and cold-formed into blanks. Forming rather than cutting keeps the grain flow continuous around the head, which is where a bolt is most likely to fail. Head dimensions and under-head radius checked at set-up and per shift.
2. ![Thread rolling machine producing bolt threads](https://engineeringhardware.com/wp-content/uploads/2026/08/03-thread-rolling-machine-bolt-production.webp) 02 **Thread rolling** Threads are rolled between hardened dies rather than cut. Rolled threads are stronger in fatigue than cut threads and hold pitch and flank angle far more consistently across a batch. Go / no-go ring gauges to ISO 965 tolerance class 6g.
3. ![Baskets of bolts staged for heat treatment](https://engineeringhardware.com/wp-content/uploads/2026/08/05-heat-treatment-baskets-black-bolts.webp) 03 **Heat treatment** Quench-and-temper brings carbon and alloy steel to the property class ordered — 8.8, 10.9 or 12.9 — with the furnace charge tracked so a finished lot can be traced back to it. Core hardness and tensile tested per lot to ISO 898-1.
4. ![Zinc plated bolts in a treatment basket](https://engineeringhardware.com/wp-content/uploads/2026/08/23-zinc-plated-bolts-treatment-basket.webp) 04 **Surface treatment** Zinc, zinc-nickel, hot-dip galvanizing, black oxide, phosphate and Dacromet, selected against the service environment rather than against the price list. Coating thickness and neutral salt spray hours to ISO 9227.

## Frequently Asked Questions

### What is the coarse-thread pitch of M8 for Channel (Strut) Nuts with Spring?

For M8 the standard coarse pitch is 1.25 mm — this is the value used for Channel (Strut) Nuts with Spring.

### What clearance and tapping drill suit M8?

Use a 9 mm clearance hole (ISO 273 medium) for through-fixing, or a 6.75 mm tapping drill for a coarse M8 thread.

### What is the height of an M8 nut?

The nominal height of a style-1 ISO 4032 M8 nut is in the spec table on this page. Style-2 (thick) is approximately 1.1× this height; thin (ISO 4035 / DIN 439) is approximately 0.5×.

### How do I request a quotation?

Use the technical drawing on this page to pick the exact configuration, then submit it with the quote form. We respond within one business day.

## Related Pages

[View the full Channel (Strut) Nuts with Spring page](https://engineeringhardware.com/fastener/channel-strut-nuts/)

### More Channel (Strut) Nuts with Spring Guides