For extension springs, DIN 2097 is the governing document for the dimensions listed below. Mechanical and performance requirements for this part family are set by its own standards, not by the bolt and screw property-class documents.
DIN 2097 — Scope
DIN 2097 specifies the dimensional requirements for extension springs. Material, surface condition and any performance rating are set by separate documents specific to this part family — ISO 898-1 and ISO 898-2, which govern bolt and nut property classes, do not apply here.
Tolerance & Product Grades
Tolerances for extension springs are given as limits on the individual dimensions in the table rather than as a fastener product grade. Where a general-tolerance class is cited on the drawing instead, it applies to the dimensions not otherwise toleranced.
Dimensions Specified by DIN 2097
| Wire dia d (mm) | Inner diameter Di (mm) | Outer diameter De (mm) | Free length Lo (mm) | Active coils n | Initial tension Fi (N) | Rate k (N/mm) | Material | Reference standard |
|---|---|---|---|---|---|---|---|---|
| 0.5 | 3.5 | 4.5 | 20 | 12 | 10 | 0.7 | Spring steel | DIN 2097 / EN 15800 |
| 0.6 | 4.5 | 5.7 | 25 | 12 | 15 | 1.2 | Spring steel | DIN 2097 / EN 15800 |
| 0.8 | 5.5 | 7.1 | 30 | 12 | 30 | 2.5 | Spring steel | DIN 2097 / EN 15800 |
| 1.0 | 7.0 | 9.0 | 40 | 15 | 45 | 3.5 | Spring steel | DIN 2097 / EN 15800 |
| 1.2 | 8.5 | 10.9 | 50 | 15 | 70 | 6.0 | Spring steel | DIN 2097 / EN 15800 |
| 1.5 | 11.0 | 14.0 | 60 | 15 | 100 | 8.0 | Spring steel | DIN 2097 / EN 15800 |
| 2.0 | 13.0 | 17.0 | 80 | 15 | 200 | 16.0 | Spring steel | DIN 2097 / EN 15800 |
| 2.5 | 17.0 | 22.0 | 100 | 15 | 380 | 30.0 | Spring steel | DIN 2097 / EN 15800 |
| 3.0 | 22.0 | 28.0 | 120 | 15 | 680 | 55.0 | Spring steel | DIN 2097 / EN 15800 |
| 4.0 | 28.0 | 36.0 | 160 | 15 | 1500 | 120.0 | Spring steel | DIN 2097 / EN 15800 |
| 5.0 | 36.0 | 46.0 | 200 | 15 | 2900 | 210.0 | Spring steel | DIN 2097 / EN 15800 |
| 6.0 | 46.0 | 58.0 | 250 | 15 | 5200 | 380.0 | Spring steel | DIN 2097 / EN 15800 |
Equivalent Standards
Where direct equivalents exist (ISO ↔ DIN, ISO ↔ ASME), they are listed on the parent Extension Springs page. Always confirm against the dimensions on this page, since some "equivalent" standards differ in tolerances and head geometry.
When to Specify DIN 2097
DIN 2097 is still widely used in European mechanical engineering and as a cross-reference on legacy drawings; its ISO equivalent is preferred for new designs.
