---
title: "DIN 6927 All-Metal Hex Flange Lock Nuts Specification"
description: "DIN 6927 All-Metal Hex Flange Lock Nuts: full dimensional table with tolerances. DIN, ISO and ASME equivalents listed side by side."
url: https://engineeringhardware.com/guide/standard/din-6927-all-metal-hex-flange-lock-nuts/
source: Engineering Hardware & Fasteners
---

# DIN 6927 All-Metal Hex Flange Lock Nuts Specification

Nuts · GB/T 6187 / DIN 6927 / ASME B18.2.2

Dimensional table, tolerance classes and the DIN / ISO / ASME parts that supersede or match this standard.

DIN 6927 specifies the dimensions and tolerances for all-metal hex flange lock nuts. The full dimensional table is reproduced below, followed by the DIN, ISO and ASME parts that match or supersede it.

- **Standard:** DIN 6927
- **Product:** All-Metal Hex Flange Lock Nuts
- **Governing standards:** GB/T 6187 / DIN 6927 / ASME B18.2.2

Equivalence between national standards is dimensional, not always metallurgical. Check the property class separately when substituting.

![DIN 6927 All-Metal Hex Flange Lock Nuts Specification reference image](https://engineeringhardware.com/wp-content/uploads/2026/09/All-Metal-Hex-Flange-Lock-Nuts.webp)

DIN 6927 is the governing dimensional standard for all-metal hex flange lock nuts. This page sets out the scope of the standard, reproduces the full size table it specifies, and lists the DIN/ISO/ASME cross-references commonly cited in datasheets and drawings.

## DIN 6927 — Scope

DIN 6927 is "Prevailing torque type hexagon nuts with flange, all-metal".

Material, property class, surface finish and packaging are governed by separate documents — ISO 898-1 and ISO 898-2 for mechanical property classes, ISO 4042 for electroplated finishes.

## Tolerance & Product Grades

DIN 6927 does not divide all-metal hex flange lock nuts into product grades. Tolerances are given as limits on the individual dimensions in the table.

Where a general-tolerance class is cited on the drawing instead, it applies to the dimensions not otherwise toleranced.

## Dimensions Specified by DIN 6927

| Strength class | Material | Locking method | Finish options | Service |
| --- | --- | --- | --- | --- |
| 8 | carbon steel | deformed all-metal thread | black oxide or zinc | general vibration-exposed joints |
| 10 | carbon steel or alloy steel | deformed all-metal thread | black oxide or zinc | higher-preload vibration service |
| 12 | alloy steel | deformed all-metal thread | black oxide or zinc | high-temperature and high-preload service |

## Equivalent Standards

Where direct equivalents exist (ISO ↔ DIN, ISO ↔ ASME), they are listed on the parent All-Metal Hex Flange Lock Nuts page.

Always confirm against the dimensions on this page, since some "equivalent" standards differ in tolerances and head geometry.

## When to Specify DIN 6927

DIN 6927 is still widely used in European mechanical engineering and as a cross-reference on legacy drawings; its ISO equivalent is preferred for new designs.

Custom manufacturing · Made to drawing

## Need a nut to this standard in a non-standard size?

Parts built to DIN 6927 are already in the catalog, so a special is usually a variation on existing tooling rather than a new design — which is what keeps the cost down. Made by cold heading or tapping.

Minimum order from 2,000 pieces; samples within 7 days of drawing approval.

[Custom nut manufacturing](https://engineeringhardware.com/custom/nuts/)[Send a drawing](https://engineeringhardware.com/custom/nuts/#rfq)

## Technical Drawing

Dimensioned line drawing of 8 All-Metal Hex Flange Lock Nuts to GB/T 6187 / DIN 6927 / ASME B18.2.2. Side view and top view, drawn to the dimensions in the table below and redrawn for any size selected.

- **Material:** carbon steel
- **Locking method:** deformed all-metal thread
- **Finish options:** black oxide or zinc
- **Service:** general vibration-exposed joints

## Dimensions & Specifications (GB/T 6187 / DIN 6927 / ASME B18.2.2)

| Strength class | Material | Locking method | Finish options | Service |
| --- | --- | --- | --- | --- |
| 8 | carbon steel | deformed all-metal thread | black oxide or zinc | general vibration-exposed joints |
| 10 | carbon steel or alloy steel | deformed all-metal thread | black oxide or zinc | higher-preload vibration service |
| 12 | alloy steel | deformed all-metal thread | black oxide or zinc | high-temperature and high-preload service |

Product catalog

## Related Flange Lock Nuts (Nylon & All-Metal) products

[![3/8″-16 Thin Hex Jam Nuts, Grade 2 Steel, Electro Zinc Plated Clear Finish](https://img.engineeringhardware.com/3-8-16-Thin-Hex-Jam-Nuts-Grade-2-Steel-Electro-Zinc-Plated-Clear-Finish.webp)](https://engineeringhardware.com/product/3-8-16-thin-hex-jam-nuts-grade-2-steel-electro-zinc-plated-clear-finish/)

Nylon-Insert & All-Metal Lock Nuts

### [3/8″-16 Thin Hex Jam Nuts, Grade 2 Steel, Electro Zinc Plated Clear Finish](https://engineeringhardware.com/product/3-8-16-thin-hex-jam-nuts-grade-2-steel-electro-zinc-plated-clear-finish/)

Stover Type All Metal Prevailing Torque Lock Nut · DIN, ANSI, GB, JIS,…

**US$0.012 – 0.036**MOQ 500 pieces

[![Metal Insertion Lock Nut Titanium Flange Nut M14](https://img.engineeringhardware.com/Metal-Insertion-Lock-Nut-Titanium-Flange-Nut-M14.webp)](https://engineeringhardware.com/product/metal-insertion-lock-nut-titanium-flange-nut-m14/)

Nylon-Insert & All-Metal Lock Nuts

### [Metal Insertion Lock Nut Titanium Flange Nut M14](https://engineeringhardware.com/product/metal-insertion-lock-nut-titanium-flange-nut-m14/)

Hexagon Head · DIN, ANSI, GB, BSW, ASME

**US$0.12 – 0.60**MOQ 1 piece

[![Premium DIN979 Stainless Steel Hex Slotted Castle Nut Round Lock Nut Castle Nut Slotted Nut Hardware Nut](https://img.engineeringhardware.com/Premium-DIN979-Stainless-Steel-Hex-Slotted-Castle-Nut-Round-Lock-Nut-Castle-Nut-Slotted-Nut-Hardware-Nut.webp)](https://engineeringhardware.com/product/premium-din979-stainless-steel-hex-slotted-castle-nut-round-lock-nut-castle-nut/)

Nylon-Insert & All-Metal Lock Nuts

### [Premium DIN979 Stainless Steel Hex Slotted Castle Nut Round Lock Nut Castle Nut Slotted Nut Hardware Nut](https://engineeringhardware.com/product/premium-din979-stainless-steel-hex-slotted-castle-nut-round-lock-nut-castle-nut/)

Hexagon Head · DIN, GB, ANSI, JIS

**US$0.60 – 1.08**MOQ 10 pieces

[![Metric DIN 6926 Hexagon Washer Self Locking Nut Stainless Steel Hex Flange Nylon Lock Nut](https://img.engineeringhardware.com/Metric-DIN-6926-Hexagon-Washer-Self-Locking-Nut-Stainless-Steel-Hex-Flange-Nylon-Lock-Nut.webp)](https://engineeringhardware.com/product/metric-din-6926-hexagon-washer-self-locking-nut-stainless-steel-hex-flange-nylon/)

Nylon-Insert & All-Metal Lock Nuts

### [Metric DIN 6926 Hexagon Washer Self Locking Nut Stainless Steel Hex Flange Nylon Lock Nut](https://engineeringhardware.com/product/metric-din-6926-hexagon-washer-self-locking-nut-stainless-steel-hex-flange-nylon/)

Hexagon Head With Flange · DIN, ANSI, GB, JIS, GOST, BSW

**US$0.012 – 0.12**MOQ 100 pieces

[![Hot DIP Galvanized Anti Vibration Heavy Duty Metal Hexagonal Lock Nut](https://img.engineeringhardware.com/Hot-DIP-Galvanized-Anti-Vibration-Heavy-Duty-Metal-Hexagonal-Lock-Nut.webp)](https://engineeringhardware.com/product/hot-dip-galvanized-anti-vibration-heavy-duty-metal-hexagonal-lock-nut/)

Nylon-Insert & All-Metal Lock Nuts

### [Hot DIP Galvanized Anti Vibration Heavy Duty Metal Hexagonal Lock Nut](https://engineeringhardware.com/product/hot-dip-galvanized-anti-vibration-heavy-duty-metal-hexagonal-lock-nut/)

Hexagon Head · DIN, ANSI, GB, JIS, GOST, BSW

**US$0.084 – 0.60**MOQ 500 pieces

[![DIN985 Hexagon Nylon Nuts with Non-Metallic Insert, Nylon Lock Nuts](https://img.engineeringhardware.com/DIN985-Hexagon-Nylon-Nuts-with-Non-Metallic-Insert-Nylon-Lock-Nuts.webp)](https://engineeringhardware.com/product/din985-hexagon-nylon-nuts-with-non-metallic-insert-nylon-lock-nuts/)

Nylon-Insert & All-Metal Lock Nuts

### [DIN985 Hexagon Nylon Nuts with Non-Metallic Insert, Nylon Lock Nuts](https://engineeringhardware.com/product/din985-hexagon-nylon-nuts-with-non-metallic-insert-nylon-lock-nuts/)

Hexagon Head · DIN, ANSI, GB, JIS, GOST, BSW

**US$0.012**MOQ 100 pieces

[View all Nylon-Insert & All-Metal Lock Nuts →](https://engineeringhardware.com/fastener-products/nuts/nylon-insert-all-metal-lock-nuts/) [Full product catalog](https://engineeringhardware.com/products/)

## Materials & Grades

Select a material class to see the grades we supply it in. Each designation is listed with its ISO/EN, AISI/SAE, JIS and GB equivalents.

Stainless Steel38 Carbon Steel66 Alloy Steel41 Bearing Steel5 Spring Steel25 Aluminum and Aluminum Alloys21 Brass17 Bronze11 Copper8 Titanium and Titanium Alloys18 Nickel and Nickel Alloys22 Iron-Nickel and High-Temperature Alloys10 Tool Steel and Specialty Hardened Steel9 Structural and Construction Steel9

### Stainless Steel

#### Austenitic Stainless Steel

- A1 AISI 303 · SAE 303 · SUS303 · EN 1.4305 · X8CrNiS18-9
- A2 AISI 304 · SAE 304 · SUS304 · EN 1.4301 · X5CrNi18-10 · 06Cr19Ni10
- 304L AISI 304L · SUS304L · EN 1.4307 · X2CrNi18-9 · 022Cr19Ni10
- 302 AISI 302 · SUS302 · EN 1.4310
- 305 AISI 305 · SUS305 · EN 1.4303
- A4 AISI 316 · SAE 316 · SUS316 · EN 1.4401 · X5CrNiMo17-12-2 · 06Cr17Ni12Mo2
- 316L AISI 316L · SUS316L · EN 1.4404 · X2CrNiMo17-12-2 · 022Cr17Ni12Mo2
- 321 AISI 321 · SUS321 · EN 1.4541 · X6CrNiTi18-10
- 310 / 310S AISI 310 · AISI 310S · SUS310S · EN 1.4845
- 302HQ AISI 302HQ
- A3
- A5
- 347 AISI 347 · SUS347 · EN 1.4550 · X6CrNiNb18-10
- 309 / 309S AISI 309 · AISI 309S · SUS309S

#### Martensitic Stainless Steel

- AISI 410 SUS410 · EN 1.4006 · X12Cr13 · 12Cr13
- AISI 420 SUS420J1 · SUS420J2 · EN 1.4021 · EN 1.4028 · 20Cr13 · 30Cr13
- AISI 431 SUS431 · EN 1.4057 · X17CrNi16-2
- C1
- C3
- C4
- AISI 440A
- AISI 440B
- AISI 440C SUS440C · EN 1.4125

#### Ferritic Stainless Steel

- AISI 430 SUS430 · EN 1.4016 · X6Cr17 · 10Cr17
- F1
- AISI 434
- AISI 444

#### Precipitation-Hardening Stainless Steel

- 17-4 PH AISI 630 · UNS S17400 · SUS630 · EN 1.4542 · X5CrNiCuNb16-4
- 15-5 PH UNS S15500
- 17-7 PH UNS S17700

#### Duplex and Super Duplex Stainless Steel

- Duplex 2205 UNS S31803 · UNS S32205 · EN 1.4462
- Super Duplex 2507 UNS S32750 · EN 1.4410
- D2
- D4
- D6
- D8
- Lean Duplex 2101 UNS S32101
- Super Duplex S32760 UNS S32760 · EN 1.4501

### Carbon Steel

#### Low-Carbon Steel

- SAE 1006
- SAE 1008
- SAE 1010
- SAE 1018
- SAE 1020
- Q195
- Q235
- SAE 1012
- SAE 1015
- Q215
- ML08
- ML08Al
- ML10
- ML15
- ML20
- SWRCH6A
- SWRCH8A
- SWRCH10A
- SWRCH12A
- SWRCH15A
- SWRCH18A

#### Medium-Carbon Steel

- SAE 1035
- SAE 1045
- S45C
- C45
- SAE 1030
- SAE 1040
- SAE 1050
- 30
- 35
- 40
- 45
- 50
- S35C
- S40C
- S50C
- C35
- C40

#### High-Carbon Steel

- SAE 1060
- SAE 1070
- 65Mn
- SAE 1065
- SAE 1075
- SAE 1080
- SAE 1085
- SAE 1090
- SAE 1095
- 60
- 65
- 70
- 75
- 80
- 85

#### Cold-Heading Steel

- SWRCH22A
- 10B21
- SWRCH22K
- SWRCH25K
- SWRCH30K
- SWRCH35K
- SWRCH40K
- ML20Mn
- ML25
- ML30
- ML35
- ML40
- 15B25

### Alloy Steel

#### Chromium Steel

- 40Cr
- 45Cr
- AISI 5140
- SAE 5140
- AISI 5120
- SAE 5120
- SCr420
- SCr440

#### Chromium-Molybdenum Steel

- 35CrMo
- 42CrMo
- AISI 4140
- SCM435
- SCM440
- 42CrMo4
- 30CrMo
- AISI 4130
- SAE 4130
- SAE 4140
- AISI 4142
- AISI 4145
- SCM415
- SCM420
- SCM445
- EN 1.7220
- EN 1.7225
- 25CrMo4
- 34CrMo4

#### Nickel-Chromium-Molybdenum Steel

- AISI 4340
- SAE 4340
- 40CrNiMo
- SNCM439
- EN 1.6511
- 36CrNiMo4

#### Boron Alloy Steel

- 10B22
- 10B21
- 15B21
- 15B25
- 20MnTiB
- 20Mn2B
- 35VB
- 40MnB

### Bearing Steel

#### Bearing Steel

- GCr15
- AISI 52100 SAE 52100 · UNS G52986
- SUJ2
- 100Cr6 EN 1.3505
- GCr15SiMn

### Spring Steel

#### Carbon Spring Steel

- SAE 1065
- SAE 1070
- SAE 1075
- SAE 1080
- SAE 1095
- 65
- 70
- 75
- 80
- 65Mn

#### Silicon-Manganese Spring Steel

- 60Si2Mn
- 60Si2MnA
- SUP6
- SUP7

#### Chromium-Vanadium Spring Steel

- 50CrVA
- SAE 6150
- AISI 6150
- SUP10

#### Stainless Spring Steel

- AISI 301
- SUS301
- EN 1.4310
- AISI 302
- AISI 304
- AISI 316
- 17-7 PH

### Aluminum and Aluminum Alloys

#### Commercially Pure Aluminum

- 1050
- 1060
- 1070
- 1100

#### 2xxx Series Aluminum

- 2024
- 2011
- 2014
- 2017

#### 5xxx Series Aluminum

- 5052
- 5083
- 5754

#### 6xxx Series Aluminum

- 6061
- 6061-T6
- 6063
- 6082
- 6082-T6

#### 7xxx Series Aluminum

- 7075
- 7075-T6
- 7005
- 7050
- 7075-T73

### Brass

#### Free-Cutting Brass

- C36000
- H62
- HPb59-1
- C3601
- C3602
- C3604
- CuZn36Pb3
- CuZn39Pb3
- EN CW614N
- EN CW617N
- H65

#### Lead-Free Brass

- C69300
- C27450
- CW510L
- CW511L

#### Naval Brass

- C46400
- CuZn39Sn1

### Bronze

#### Silicon Bronze

- C65500
- C65100
- C65600

#### Phosphor Bronze

- C51000
- C52100
- CuSn6
- CuSn8

#### Aluminum Bronze

- C95400
- C95500
- C63000
- CuAl10Ni5Fe4

### Copper

#### Copper

- C11000
- T2
- C10100
- C10200
- C12200
- T1
- TU1
- TU2

### Titanium and Titanium Alloys

#### Commercially Pure Titanium

- Grade 2
- Grade 1
- Grade 3
- Grade 4
- TA1
- TA2
- TA3

#### Alpha-Beta Titanium Alloys

- Grade 5
- Ti-6Al-4V
- TC4
- UNS R56400

#### Low-Interstitial Grade

- Grade 23
- Ti-6Al-4V ELI
- UNS R56407

#### Other Titanium Fastener Alloys

- Ti-6Al-6V-2Sn
- Ti-6Al-2Sn-4Zr-2Mo
- Beta-C titanium
- Ti-10V-2Fe-3Al

### Nickel and Nickel Alloys

#### Commercially Pure Nickel

- Nickel 200
- UNS N02200
- Nickel 201
- UNS N02201

#### Inconel Alloys

- Inconel 625 UNS N06625
- Inconel 718 UNS N07718
- Inconel 600 UNS N06600
- Inconel 601 UNS N06601
- Inconel 686 UNS N06686
- Inconel X-750 UNS N07750

#### Monel Alloys

- Monel 400 UNS N04400
- Monel K-500 UNS N05500

#### Hastelloy Alloys

- Hastelloy C-276 UNS N10276
- Hastelloy C-22 UNS N06022
- Hastelloy B-2 UNS N10665
- Hastelloy B-3 UNS N10675
- Hastelloy X UNS N06002

#### Other Nickel Alloys

- Alloy 20 UNS N08020
- Alloy 625
- Alloy 718
- Alloy 825 UNS N08825
- Alloy 925 UNS N09925

### Iron-Nickel and High-Temperature Alloys

#### A286

- A-286
- UNS S66286
- EN 1.4980

#### Invar

- Invar 36
- Alloy 36
- UNS K93600
- FeNi36

#### Alloy 42

- Alloy 42
- UNS K94100
- FeNi42

### Tool Steel and Specialty Hardened Steel

#### Tool Steel and Specialty Hardened Steel

- AISI D2
- AISI H13
- SKD11
- Cr12MoV
- AISI O1
- AISI A2
- AISI S7
- SKD61
- 9CrSi

### Structural and Construction Steel

#### Structural and Construction Steel

- ASTM A36
- Q235B
- Q355B
- S355JR
- Q235C
- Q355C
- S235JR
- S275JR
- S355J2

## Applications & Industries

The sectors that buy All-Metal Hex Flange Lock Nuts to GB/T 6187 / DIN 6927 / ASME B18.2.2, and the duty each one buys them for. Stocked from 8 to 12 (nominal diameter).

### Industries that specify All-Metal Hex Flange Lock Nuts

- **Vehicle chassis:** Prevailing torque plus a flange bearing face in one part.
- **Rotating machinery:** Vibration resistance without a separate lock washer.
- **Heavy equipment:** Class 10 and 12 for higher preload joints.
- **Exhaust and hot assemblies:** All-metal locking survives temperatures that destroy a nylon insert.
- **Machine building & OEM:** The clamping counter-face on studs and bolts throughout an assembly.
- **Steel fabrication:** Bolted structural and frame connections.

### Typical applications

- selecting class 8, 10 or 12 against the bolt grade
- using it where service temperature rules out nylon
- checking the flange seats fully on the joint face
- replacing a nut plus lock washer with one flanged part
- completing a bolted joint on a stud, rod or bolt
- locking an adjustment so it cannot drift

### Service conditions to specify against

- **Marine and coastal:** Available in A4 (316) stainless for chloride exposure — coastal structures, pool halls, water treatment and deck hardware, where A2 will eventually pit.
- **High load:** Supplied in ISO 898-1 property classes, so the joint can be designed to a stated proof load and tightened to a calculated torque rather than by feel.
- **Vibration:** Specified where cyclic load would loosen a plain nut or screw — rotating plant, rail, mobile equipment and anything that is not re-torqued in service.
- **Match the class:** A nut below the bolt property class strips before the bolt reaches its own limit — pair class 8 nuts with 8.8 bolts, class 10 with 10.9.

### Where to use something else

- Do not re-use an all-metal lock nut indefinitely; the deformed thread loses prevailing torque each time it is run on.

[Full application guide: where All-Metal Hex Flange Lock Nuts are used, how to specify them, and the cases they are wrong for](https://engineeringhardware.com/applications/all-metal-hex-flange-lock-nuts/)

Inside the plant

## Manufactured in our own plant

This part is cold-formed, threaded, heat-treated and finished in-house. The stages below are where its class and finish are actually decided.

1. ![Wire rod feeding into a cold heading machine](https://engineeringhardware.com/wp-content/uploads/2026/08/09-wire-rod-feed-cold-heading-machine.webp) 01 **Cold heading** Wire rod is drawn to size and cold-formed into blanks. Forming rather than cutting keeps the grain flow continuous around the head, which is where a bolt is most likely to fail. Head dimensions and under-head radius checked at set-up and per shift.
2. ![Thread rolling machine producing bolt threads](https://engineeringhardware.com/wp-content/uploads/2026/08/03-thread-rolling-machine-bolt-production.webp) 02 **Thread rolling** Threads are rolled between hardened dies rather than cut. Rolled threads are stronger in fatigue than cut threads and hold pitch and flank angle far more consistently across a batch. Go / no-go ring gauges to ISO 965 tolerance class 6g.
3. ![Baskets of bolts staged for heat treatment](https://engineeringhardware.com/wp-content/uploads/2026/08/05-heat-treatment-baskets-black-bolts.webp) 03 **Heat treatment** Quench-and-temper brings carbon and alloy steel to the property class ordered — 8.8, 10.9 or 12.9 — with the furnace charge tracked so a finished lot can be traced back to it. Core hardness and tensile tested per lot to ISO 898-1.
4. ![Zinc plated bolts in a treatment basket](https://engineeringhardware.com/wp-content/uploads/2026/08/23-zinc-plated-bolts-treatment-basket.webp) 04 **Surface treatment** Zinc, zinc-nickel, hot-dip galvanizing, black oxide, phosphate and Dacromet, selected against the service environment rather than against the price list. Coating thickness and neutral salt spray hours to ISO 9227.

## Frequently Asked Questions

### What is DIN 6927?

DIN 6927 is "Prevailing torque type hexagon nuts with flange, all-metal".

### What does DIN 6927 specify for All-Metal Hex Flange Lock Nuts?

DIN 6927 specifies the dimensions and tolerances of all-metal hex flange lock nuts. Material and property class are governed by separate documents.

### Does DIN 6927 specify the mechanical strength?

No. DIN 6927 controls only the geometry of all-metal hex flange lock nuts. The mechanical strength is set by ISO 898-1 (bolts, screws and studs) or ISO 898-2 (nuts), and the finish by separate documents.

### Can I substitute DIN 6927 for the corresponding DIN standard on a drawing?

On modern drawings the ISO standard is the master reference; the older DIN equivalent is a cross-reference. For most dimensional purposes the parts are interchangeable, but check tolerance grades and the head height — these are the most common points of divergence.

### How do I request a quotation?

Use the technical drawing on this page to pick the exact configuration, then submit it with the quote form. We respond within one business day.

## Related Pages

[View the full All-Metal Hex Flange Lock Nuts page](https://engineeringhardware.com/fastener/all-metal-hex-flange-lock-nuts/)

### More All-Metal Hex Flange Lock Nuts Guides