--- title: "GB T 901 Stud / Threaded Rod Specification" description: "GB T 901 Stud / Threaded Rod: full dimensional table with tolerances. DIN, ISO and ASME equivalents listed side by side." url: https://engineeringhardware.com/guide/standard/gb-t-901-cad-svg-091-stud/ source: Engineering Hardware & Fasteners --- # GB T 901 Stud / Threaded Rod Specification Bolts · ISO / DIN Dimensional table, tolerance classes and the DIN / ISO / ASME parts that supersede or match this standard. GB T 901 specifies the dimensions and tolerances for stud / threaded rod. The full dimensional table is reproduced below, followed by the DIN, ISO and ASME parts that match or supersede it. - **Standard:** GB T 901 - **Product:** Stud / Threaded Rod — ISO / DIN (Series 154) - **Governing standards:** ISO / DIN Equivalence between national standards is dimensional, not always metallurgical. Check the property class separately when substituting. ![GB T 901 Stud / Threaded Rod Specification reference image](https://engineeringhardware.com/wp-content/uploads/2026/06/Stud-Threaded-Rod-—-ISO-DIN-Series-154-—-ISO-DIN.webp) GB T 901 is the governing dimensional standard for stud / threaded rod. This page sets out the scope of the standard, reproduces the full size table it specifies, and lists the DIN/ISO/ASME cross-references commonly cited in datasheets and drawings. ## GB T 901 — Scope GB T 901 is "Double end studs — Metal end 1.25 d". GB/T 901 is the Chinese national adoption of the same document. Material, property class, surface finish and packaging are governed by separate documents — ISO 898-1 and ISO 898-2 for mechanical property classes, ISO 4042 for electroplated finishes. ## Tolerance & Product Grades GB T 901 does not divide stud / threaded rod — iso / din (series 154) into product grades. Tolerances are given as limits on the individual dimensions in the table. Where a general-tolerance class is cited on the drawing instead, it applies to the dimensions not otherwise toleranced. ## Dimensions Specified by GB T 901 | Thread size | Pitch (mm) | Length L (mm) | Engagement depth bm (mm) | Material | Reference standard | | --- | --- | --- | --- | --- | --- | | M6 | 1.0 | 50 | 8 | Cl. 8.8 alloy steel | DIN 939 / GB/T 901 | | M8 | 1.25 | 60 | 10 | Cl. 8.8 alloy steel | DIN 939 / GB/T 901 | | M10 | 1.5 | 80 | 15 | Cl. 8.8 alloy steel | DIN 939 / GB/T 901 | | M12 | 1.75 | 100 | 18 | Cl. 8.8 alloy steel | DIN 939 / GB/T 901 | | M14 | 2.0 | 120 | 21 | Cl. 8.8 alloy steel | DIN 939 / GB/T 901 | | M16 | 2.0 | 150 | 24 | Cl. 8.8 alloy steel | DIN 939 / GB/T 901 | | M20 | 2.5 | 180 | 30 | Cl. 8.8 alloy steel | DIN 939 / GB/T 901 | | M24 | 3.0 | 200 | 36 | Cl. 8.8 alloy steel | DIN 939 / GB/T 901 | | M30 | 3.5 | 240 | 45 | Cl. 8.8 alloy steel | DIN 939 / GB/T 901 | | M36 | 4.0 | 280 | 54 | Cl. 8.8 alloy steel | DIN 939 / GB/T 901 | ## Equivalent Standards Where direct equivalents exist (ISO ↔ DIN, ISO ↔ ASME), they are listed on the parent Stud / Threaded Rod — ISO / DIN (Series 154) page. Always confirm against the dimensions on this page, since some "equivalent" standards differ in tolerances and head geometry. ## Companion Standards GB T 901 controls only the geometry of stud / threaded rod — iso / din (series 154). The mechanical strength is set by ISO 898-1 (bolts, screws and studs) or ISO 898-2 (nuts); the surface finish is governed by separate finish standards such as ISO 4042 for electroplating. For corrosion testing, the relevant document is ISO 9227 (neutral salt spray). Custom manufacturing · Made to drawing ## Need a bolt to this standard in a non-standard size? Parts built to GB T 901 are already in the catalog, so a special is usually a variation on existing tooling rather than a new design — which is what keeps the cost down. Made by cold heading or hot forging. Minimum order from 2,000 pieces; samples within 7 days of drawing approval. [Custom bolt manufacturing](https://engineeringhardware.com/custom/bolts/)[Send a drawing](https://engineeringhardware.com/custom/bolts/#rfq) ## Technical Drawing Dimensioned line drawing of M6 Stud / Threaded Rod — ISO / DIN (Series 154). Side view and top view, drawn to the dimensions in the table below and redrawn for any size selected. - **Pitch (mm):** 1.0 - **Length L (mm):** 50 - **Engagement depth bm (mm):** 8 - **Material:** Cl. 8.8 alloy steel ## Dimensions & Specifications (ISO / DIN) | Thread size | Pitch (mm) | Length L (mm) | Engagement depth bm (mm) | Material | Reference standard | | --- | --- | --- | --- | --- | --- | | M6 | 1.0 | 50 | 8 | Cl. 8.8 alloy steel | DIN 939 / GB/T 901 | | M8 | 1.25 | 60 | 10 | Cl. 8.8 alloy steel | DIN 939 / GB/T 901 | | M10 | 1.5 | 80 | 15 | Cl. 8.8 alloy steel | DIN 939 / GB/T 901 | | M12 | 1.75 | 100 | 18 | Cl. 8.8 alloy steel | DIN 939 / GB/T 901 | | M14 | 2.0 | 120 | 21 | Cl. 8.8 alloy steel | DIN 939 / GB/T 901 | | M16 | 2.0 | 150 | 24 | Cl. 8.8 alloy steel | DIN 939 / GB/T 901 | | M20 | 2.5 | 180 | 30 | Cl. 8.8 alloy steel | DIN 939 / GB/T 901 | | M24 | 3.0 | 200 | 36 | Cl. 8.8 alloy steel | DIN 939 / GB/T 901 | | M30 | 3.5 | 240 | 45 | Cl. 8.8 alloy steel | DIN 939 / GB/T 901 | | M36 | 4.0 | 280 | 54 | Cl. 8.8 alloy steel | DIN 939 / GB/T 901 | ## Materials & Grades Select a material class to see the grades we supply it in. Each designation is listed with its ISO/EN, AISI/SAE, JIS and GB equivalents. Stainless Steel38 Carbon Steel66 Alloy Steel41 Bearing Steel5 Spring Steel25 Aluminum and Aluminum Alloys21 Brass17 Bronze11 Copper8 Titanium and Titanium Alloys18 Nickel and Nickel Alloys22 Iron-Nickel and High-Temperature Alloys10 Tool Steel and Specialty Hardened Steel9 Structural and Construction Steel9 ### Stainless Steel #### Austenitic Stainless Steel - A1 AISI 303 · SAE 303 · SUS303 · EN 1.4305 · X8CrNiS18-9 - A2 AISI 304 · SAE 304 · SUS304 · EN 1.4301 · X5CrNi18-10 · 06Cr19Ni10 - 304L AISI 304L · SUS304L · EN 1.4307 · X2CrNi18-9 · 022Cr19Ni10 - 302 AISI 302 · SUS302 · EN 1.4310 - 305 AISI 305 · SUS305 · EN 1.4303 - A4 AISI 316 · SAE 316 · SUS316 · EN 1.4401 · X5CrNiMo17-12-2 · 06Cr17Ni12Mo2 - 316L AISI 316L · SUS316L · EN 1.4404 · X2CrNiMo17-12-2 · 022Cr17Ni12Mo2 - 321 AISI 321 · SUS321 · EN 1.4541 · X6CrNiTi18-10 - 310 / 310S AISI 310 · AISI 310S · SUS310S · EN 1.4845 - 302HQ AISI 302HQ - A3 - A5 - 347 AISI 347 · SUS347 · EN 1.4550 · X6CrNiNb18-10 - 309 / 309S AISI 309 · AISI 309S · SUS309S #### Martensitic Stainless Steel - AISI 410 SUS410 · EN 1.4006 · X12Cr13 · 12Cr13 - AISI 420 SUS420J1 · SUS420J2 · EN 1.4021 · EN 1.4028 · 20Cr13 · 30Cr13 - AISI 431 SUS431 · EN 1.4057 · X17CrNi16-2 - C1 - C3 - C4 - AISI 440A - AISI 440B - AISI 440C SUS440C · EN 1.4125 #### Ferritic Stainless Steel - AISI 430 SUS430 · EN 1.4016 · X6Cr17 · 10Cr17 - F1 - AISI 434 - AISI 444 #### Precipitation-Hardening Stainless Steel - 17-4 PH AISI 630 · UNS S17400 · SUS630 · EN 1.4542 · X5CrNiCuNb16-4 - 15-5 PH UNS S15500 - 17-7 PH UNS S17700 #### Duplex and Super Duplex Stainless Steel - Duplex 2205 UNS S31803 · UNS S32205 · EN 1.4462 - Super Duplex 2507 UNS S32750 · EN 1.4410 - D2 - D4 - D6 - D8 - Lean Duplex 2101 UNS S32101 - Super Duplex S32760 UNS S32760 · EN 1.4501 ### Carbon Steel #### Low-Carbon Steel - SAE 1006 - SAE 1008 - SAE 1010 - SAE 1018 - SAE 1020 - Q195 - Q235 - SAE 1012 - SAE 1015 - Q215 - ML08 - ML08Al - ML10 - ML15 - ML20 - SWRCH6A - SWRCH8A - SWRCH10A - SWRCH12A - SWRCH15A - SWRCH18A #### Medium-Carbon Steel - SAE 1035 - SAE 1045 - S45C - C45 - SAE 1030 - SAE 1040 - SAE 1050 - 30 - 35 - 40 - 45 - 50 - S35C - S40C - S50C - C35 - C40 #### High-Carbon Steel - SAE 1060 - SAE 1070 - 65Mn - SAE 1065 - SAE 1075 - SAE 1080 - SAE 1085 - SAE 1090 - SAE 1095 - 60 - 65 - 70 - 75 - 80 - 85 #### Cold-Heading Steel - SWRCH22A - 10B21 - SWRCH22K - SWRCH25K - SWRCH30K - SWRCH35K - SWRCH40K - ML20Mn - ML25 - ML30 - ML35 - ML40 - 15B25 ### Alloy Steel #### Chromium Steel - 40Cr - 45Cr - AISI 5140 - SAE 5140 - AISI 5120 - SAE 5120 - SCr420 - SCr440 #### Chromium-Molybdenum Steel - 35CrMo - 42CrMo - AISI 4140 - SCM435 - SCM440 - 42CrMo4 - 30CrMo - AISI 4130 - SAE 4130 - SAE 4140 - AISI 4142 - AISI 4145 - SCM415 - SCM420 - SCM445 - EN 1.7220 - EN 1.7225 - 25CrMo4 - 34CrMo4 #### Nickel-Chromium-Molybdenum Steel - AISI 4340 - SAE 4340 - 40CrNiMo - SNCM439 - EN 1.6511 - 36CrNiMo4 #### Boron Alloy Steel - 10B22 - 10B21 - 15B21 - 15B25 - 20MnTiB - 20Mn2B - 35VB - 40MnB ### Bearing Steel #### Bearing Steel - GCr15 - AISI 52100 SAE 52100 · UNS G52986 - SUJ2 - 100Cr6 EN 1.3505 - GCr15SiMn ### Spring Steel #### Carbon Spring Steel - SAE 1065 - SAE 1070 - SAE 1075 - SAE 1080 - SAE 1095 - 65 - 70 - 75 - 80 - 65Mn #### Silicon-Manganese Spring Steel - 60Si2Mn - 60Si2MnA - SUP6 - SUP7 #### Chromium-Vanadium Spring Steel - 50CrVA - SAE 6150 - AISI 6150 - SUP10 #### Stainless Spring Steel - AISI 301 - SUS301 - EN 1.4310 - AISI 302 - AISI 304 - AISI 316 - 17-7 PH ### Aluminum and Aluminum Alloys #### Commercially Pure Aluminum - 1050 - 1060 - 1070 - 1100 #### 2xxx Series Aluminum - 2024 - 2011 - 2014 - 2017 #### 5xxx Series Aluminum - 5052 - 5083 - 5754 #### 6xxx Series Aluminum - 6061 - 6061-T6 - 6063 - 6082 - 6082-T6 #### 7xxx Series Aluminum - 7075 - 7075-T6 - 7005 - 7050 - 7075-T73 ### Brass #### Free-Cutting Brass - C36000 - H62 - HPb59-1 - C3601 - C3602 - C3604 - CuZn36Pb3 - CuZn39Pb3 - EN CW614N - EN CW617N - H65 #### Lead-Free Brass - C69300 - C27450 - CW510L - CW511L #### Naval Brass - C46400 - CuZn39Sn1 ### Bronze #### Silicon Bronze - C65500 - C65100 - C65600 #### Phosphor Bronze - C51000 - C52100 - CuSn6 - CuSn8 #### Aluminum Bronze - C95400 - C95500 - C63000 - CuAl10Ni5Fe4 ### Copper #### Copper - C11000 - T2 - C10100 - C10200 - C12200 - T1 - TU1 - TU2 ### Titanium and Titanium Alloys #### Commercially Pure Titanium - Grade 2 - Grade 1 - Grade 3 - Grade 4 - TA1 - TA2 - TA3 #### Alpha-Beta Titanium Alloys - Grade 5 - Ti-6Al-4V - TC4 - UNS R56400 #### Low-Interstitial Grade - Grade 23 - Ti-6Al-4V ELI - UNS R56407 #### Other Titanium Fastener Alloys - Ti-6Al-6V-2Sn - Ti-6Al-2Sn-4Zr-2Mo - Beta-C titanium - Ti-10V-2Fe-3Al ### Nickel and Nickel Alloys #### Commercially Pure Nickel - Nickel 200 - UNS N02200 - Nickel 201 - UNS N02201 #### Inconel Alloys - Inconel 625 UNS N06625 - Inconel 718 UNS N07718 - Inconel 600 UNS N06600 - Inconel 601 UNS N06601 - Inconel 686 UNS N06686 - Inconel X-750 UNS N07750 #### Monel Alloys - Monel 400 UNS N04400 - Monel K-500 UNS N05500 #### Hastelloy Alloys - Hastelloy C-276 UNS N10276 - Hastelloy C-22 UNS N06022 - Hastelloy B-2 UNS N10665 - Hastelloy B-3 UNS N10675 - Hastelloy X UNS N06002 #### Other Nickel Alloys - Alloy 20 UNS N08020 - Alloy 625 - Alloy 718 - Alloy 825 UNS N08825 - Alloy 925 UNS N09925 ### Iron-Nickel and High-Temperature Alloys #### A286 - A-286 - UNS S66286 - EN 1.4980 #### Invar - Invar 36 - Alloy 36 - UNS K93600 - FeNi36 #### Alloy 42 - Alloy 42 - UNS K94100 - FeNi42 ### Tool Steel and Specialty Hardened Steel #### Tool Steel and Specialty Hardened Steel - AISI D2 - AISI H13 - SKD11 - Cr12MoV - AISI O1 - AISI A2 - AISI S7 - SKD61 - 9CrSi ### Structural and Construction Steel #### Structural and Construction Steel - ASTM A36 - Q235B - Q355B - S355JR - Q235C - Q355C - S235JR - S275JR - S355J2 ## Applications & Industries Where Stud / Threaded Rod are used, and what decides the specification in each case. Stocked from M6 to M36. ### Industries that specify Stud / Threaded Rod - **Pressure equipment & flanges:** Studs and nuts on flanged joints, where both ends are tightened and the assembly is inspected. - **Plant & machine installation:** Anchoring and levelling machines onto bases and frames. - **Steel fabrication:** Hanger rods, tie rods and made-to-length threaded assemblies. - **Building services:** Threaded rod suspension for tray, duct and pipework. ### Typical applications - suspending services from a soffit on threaded rod - made-to-length assemblies cut and threaded on site - clamping a joint from both ends where a headed bolt will not fit ### Service conditions to specify against - **Marine and coastal:** Available in A4 (316) stainless for chloride exposure — coastal structures, pool halls, water treatment and deck hardware, where A2 will eventually pit. - **High load:** Supplied in ISO 898-1 property classes, so the joint can be designed to a stated proof load and tightened to a calculated torque rather than by feel. ### Where to use something else - Not for a joint that must be tightened from one side only — there is no head to hold. [Full application guide: where Stud / Threaded Rod are used, how to specify them, and the cases they are wrong for](https://engineeringhardware.com/applications/cad-svg-154-stud/) Inside the plant ## Manufactured in our own plant This part is cold-formed, threaded, heat-treated and finished in-house. The stages below are where its class and finish are actually decided. 1. ![Wire rod feeding into a cold heading machine](https://engineeringhardware.com/wp-content/uploads/2026/08/09-wire-rod-feed-cold-heading-machine.webp) 01 **Cold heading** Wire rod is drawn to size and cold-formed into blanks. Forming rather than cutting keeps the grain flow continuous around the head, which is where a bolt is most likely to fail. Head dimensions and under-head radius checked at set-up and per shift. 2. ![Thread rolling machine producing bolt threads](https://engineeringhardware.com/wp-content/uploads/2026/08/03-thread-rolling-machine-bolt-production.webp) 02 **Thread rolling** Threads are rolled between hardened dies rather than cut. Rolled threads are stronger in fatigue than cut threads and hold pitch and flank angle far more consistently across a batch. Go / no-go ring gauges to ISO 965 tolerance class 6g. 3. ![Baskets of bolts staged for heat treatment](https://engineeringhardware.com/wp-content/uploads/2026/08/05-heat-treatment-baskets-black-bolts.webp) 03 **Heat treatment** Quench-and-temper brings carbon and alloy steel to the property class ordered — 8.8, 10.9 or 12.9 — with the furnace charge tracked so a finished lot can be traced back to it. Core hardness and tensile tested per lot to ISO 898-1. 4. ![Zinc plated bolts in a treatment basket](https://engineeringhardware.com/wp-content/uploads/2026/08/23-zinc-plated-bolts-treatment-basket.webp) 04 **Surface treatment** Zinc, zinc-nickel, hot-dip galvanizing, black oxide, phosphate and Dacromet, selected against the service environment rather than against the price list. Coating thickness and neutral salt spray hours to ISO 9227. ## Frequently Asked Questions ### What is GB T 901? GB T 901 is "Double end studs — Metal end 1.25 d". GB/T 901 is the Chinese national adoption of the same document. ### What does GB T 901 specify for Stud / Threaded Rod — ISO / DIN (Series 154)? GB T 901 specifies the dimensions and tolerances of stud / threaded rod — iso / din (series 154). Material and property class are governed by separate documents. ### Does GB T 901 specify the mechanical strength? No. GB T 901 controls only the geometry of stud / threaded rod — iso / din (series 154). The mechanical strength is set by ISO 898-1 (bolts, screws and studs) or ISO 898-2 (nuts), and the finish by separate documents. ### Can I substitute GB T 901 for the corresponding DIN standard on a drawing? On modern drawings the ISO standard is the master reference; the older DIN equivalent is a cross-reference. For most dimensional purposes the parts are interchangeable, but check tolerance grades and the head height — these are the most common points of divergence. ### How do I request a quotation? Use the technical drawing on this page to pick the exact configuration, then submit it with the quote form. We respond within one business day. ## Related Pages [View the full Stud / Threaded Rod — ISO / DIN (Series 154) page](https://engineeringhardware.com/fastener/cad-svg-154-stud/) ### More Stud / Threaded Rod — ISO / DIN (Series 154) Guides