--- title: "ISO 7045 SEMS Screws with Captive Flat Washers Specification" description: "ISO 7045 SEMS Screws with Captive Flat Washers: full dimensional table with tolerances. DIN, ISO and ASME equivalents listed side by side." url: https://engineeringhardware.com/guide/standard/iso-7045-pan-head-screws/ source: Engineering Hardware & Fasteners --- # ISO 7045 SEMS Screws with Captive Flat Washers Specification Screws · DIN 7985 / ISO 7045 and EN ISO 10644 Dimensional table, tolerance classes and the DIN / ISO / ASME parts that supersede or match this standard. ISO 7045 specifies the dimensions and tolerances for sems screws with captive flat washers. The full dimensional table is reproduced below, followed by the DIN, ISO and ASME parts that match or supersede it. - **Standard:** ISO 7045 - **Product:** SEMS Screws with Captive Flat Washers - **Governing standards:** DIN 7985 / ISO 7045 and EN ISO 10644 Equivalence between national standards is dimensional, not always metallurgical. Check the property class separately when substituting. ![ISO 7045 SEMS Screws with Captive Flat Washers Specification reference image](https://engineeringhardware.com/wp-content/uploads/2026/09/SEMS-Screws-with-Captive-Flat-Washers.webp) ISO 7045 is the governing dimensional standard for sems screws with captive flat washers. This page sets out the scope of the standard, reproduces the full size table it specifies, and lists the DIN/ISO/ASME cross-references commonly cited in datasheets and drawings. ## ISO 7045 — Scope ISO 7045 is "Pan head screws with type H or type Z cross recess — Product grade A". Material, property class, surface finish and packaging are governed by separate documents — ISO 898-1 and ISO 898-2 for mechanical property classes, ISO 4042 for electroplated finishes. ## Tolerance & Product Grades ISO 7045 is written to product grade A; a different grade of the same part is a different document in the family, not a variant of this one. ## Dimensions Specified by ISO 7045 | Thread size | Pitch (mm) | Washer outside diameter (mm) | Washer thickness (mm) | Property/material options | Drive | Reference standard | | --- | --- | --- | --- | --- | --- | --- | | M2.5 | 0.45 | 6 | 0.6 | steel 4.8/8.8 or A2 stainless | Phillips | DIN 7985 / ISO 7045 and EN ISO 10644 | | M3 | 0.5 | 7 | 0.6 | steel 4.8/8.8 or A2 stainless | Phillips | DIN 7985 / ISO 7045 and EN ISO 10644 | | M4 | 0.7 | 9 | 0.8 | steel 4.8/8.8 or A2 stainless | Phillips | DIN 7985 / ISO 7045 and EN ISO 10644 | | M5 | 0.8 | 10 | 1.0 | steel 4.8/8.8 or A2 stainless | Phillips | DIN 7985 / ISO 7045 and EN ISO 10644 | | M6 | 1.0 | 12 | 1.6 | steel 4.8/8.8 or A2 stainless | Phillips | DIN 7985 / ISO 7045 and EN ISO 10644 | | M8 | 1.25 | 16 | 2.0 | steel 4.8/8.8 or A2 stainless | Phillips | DIN 7985 / ISO 7045 and EN ISO 10644 | ## Companion Standards ISO 7045 controls only the geometry of sems screws with captive flat washers. The mechanical strength is set by ISO 898-1 (bolts, screws and studs) or ISO 898-2 (nuts); the surface finish is governed by separate finish standards such as ISO 4042 for electroplating. For corrosion testing, the relevant document is ISO 9227 (neutral salt spray). ## When to Specify ISO 7045 Choose ISO 7045 for international engineering work and OEM supply where ISO standards are the contractual reference. It is the default modern specification for sems screws with captive flat washers. Custom manufacturing · Made to drawing ## Need a screw to this standard in a non-standard size? Parts built to ISO 7045 are already in the catalog, so a special is usually a variation on existing tooling rather than a new design — which is what keeps the cost down. Made by cold heading or warm forging. Minimum order from 2,000 pieces; samples within 7 days of drawing approval. [Custom screw manufacturing](https://engineeringhardware.com/custom/screws/)[Send a drawing](https://engineeringhardware.com/custom/screws/#rfq) ## Technical Drawing Dimensioned line drawing of M2.5 SEMS Screws with Captive Flat Washers to DIN 7985 / ISO 7045 and EN ISO 10644. Side view and top view, drawn to the dimensions in the table below and redrawn for any size selected. - **Pitch (mm):** 0.45 - **Washer outside diameter (mm):** 6 - **Washer thickness (mm):** 0.6 - **Property/material options:** steel 4.8/8.8 or A2 stainless - **Drive:** Phillips ## Dimensions & Specifications (DIN 7985 / ISO 7045 and EN ISO 10644) | Thread size | Pitch (mm) | Washer outside diameter (mm) | Washer thickness (mm) | Property/material options | Drive | Reference standard | | --- | --- | --- | --- | --- | --- | --- | | M2.5 | 0.45 | 6 | 0.6 | steel 4.8/8.8 or A2 stainless | Phillips | DIN 7985 / ISO 7045 and EN ISO 10644 | | M3 | 0.5 | 7 | 0.6 | steel 4.8/8.8 or A2 stainless | Phillips | DIN 7985 / ISO 7045 and EN ISO 10644 | | M4 | 0.7 | 9 | 0.8 | steel 4.8/8.8 or A2 stainless | Phillips | DIN 7985 / ISO 7045 and EN ISO 10644 | | M5 | 0.8 | 10 | 1.0 | steel 4.8/8.8 or A2 stainless | Phillips | DIN 7985 / ISO 7045 and EN ISO 10644 | | M6 | 1.0 | 12 | 1.6 | steel 4.8/8.8 or A2 stainless | Phillips | DIN 7985 / ISO 7045 and EN ISO 10644 | | M8 | 1.25 | 16 | 2.0 | steel 4.8/8.8 or A2 stainless | Phillips | DIN 7985 / ISO 7045 and EN ISO 10644 | Product catalog ## Related Pan Head Screws products [![DIN 85 304 Stainless Steel Plain Finish Machine Screws Slotted Pan Head Screws 70](https://img.engineeringhardware.com/DIN-85-304-Stainless-Steel-Plain-Finish-Machine-Screws-Slotted-Pan-Head-Screws-70.webp)](https://engineeringhardware.com/product/din-85-304-stainless-steel-plain-finish-machine-screws-slotted-pan-head-screws-70/) Button, Pan & Round-Head Screws ### [DIN 85 304 Stainless Steel Plain Finish Machine Screws Slotted Pan Head Screws 70](https://engineeringhardware.com/product/din-85-304-stainless-steel-plain-finish-machine-screws-slotted-pan-head-screws-70/) Hexagon Head · DIN, GB **US$0.012**MOQ 100 pieces [![304 Stainless Steel Pan Head Semi Tubular Rivet Custom Non Standard Metal Rivet](https://img.engineeringhardware.com/304-Stainless-Steel-Pan-Head-Semi-Tubular-Rivet-Custom-Non-Standard-Metal-Rivet.webp)](https://engineeringhardware.com/product/304-stainless-steel-pan-head-semi-tubular-rivet-custom-non-standard-metal-rivet/) Button, Pan & Round-Head Screws ### [304 Stainless Steel Pan Head Semi Tubular Rivet Custom Non Standard Metal Rivet](https://engineeringhardware.com/product/304-stainless-steel-pan-head-semi-tubular-rivet-custom-non-standard-metal-rivet/) High-Carbon Steel · 4.8mm,6.4mm or Customizable **US$0.0036 – 0.006**MOQ 1,000 pieces [![Hot Sale Stainless Steel/Carbon/Alloy Steel Flat Sheet/Black Sheet/Flat Sheet/Spring Washer/Electronic Screw in Stock](https://img.engineeringhardware.com/Hot-Sale-Stainless-Steel-Carbon-Alloy-Steel-Flat-Sheet-Black-Sheet-Flat-Sheet-Spring-Washer-Electronic-Screw-in-Stock.webp)](https://engineeringhardware.com/product/hot-sale-stainless-steel-carbon-alloy-steel-flat-sheet-black-sheet-flat-sheet-spring-2/) Button, Pan & Round-Head Screws ### [Hot Sale Stainless Steel/Carbon/Alloy Steel Flat Sheet/Black Sheet/Flat Sheet/Spring Washer/Electronic Screw in Stock](https://engineeringhardware.com/product/hot-sale-stainless-steel-carbon-alloy-steel-flat-sheet-black-sheet-flat-sheet-spring-2/) Pan Head · DIN, GB, ANSI, BSW, JIS **US$48.00 – 72.00**MOQ 1 piece [![304 Stainless Steel Half Round Head Hexagonal Socket Machine Screw / Black Plated Bowl Cut Screw Half Round Head Bolt M3/M4/M5/M6/M8/M10](https://img.engineeringhardware.com/304-Stainless-Steel-Half-Round-Head-Hexagonal-Socket-Machine-Screw-Black-Plated-Bowl-Cut-Screw-Half-Round-Head-Bolt-M3-M4-M5-M6-M8-M10.webp)](https://engineeringhardware.com/product/304-stainless-steel-half-round-head-hexagonal-socket-machine-screw-black-plated-bowl/) Button, Pan & Round-Head Screws ### [304 Stainless Steel Half Round Head Hexagonal Socket Machine Screw / Black Plated Bowl Cut Screw Half Round Head Bolt M3/M4/M5/M6/M8/M10](https://engineeringhardware.com/product/304-stainless-steel-half-round-head-hexagonal-socket-machine-screw-black-plated-bowl/) Machine Screw · Stainless Steel/ Carbon Steel **Price on request**MOQ 1,000 pieces [![Wholesale Quality Pan Head Screw Stainless Steel Screw](https://img.engineeringhardware.com/Wholesale-Quality-Pan-Head-Screw-Stainless-Steel-Screw.webp)](https://engineeringhardware.com/product/wholesale-quality-pan-head-screw-stainless-steel-screw/) Button, Pan & Round-Head Screws ### [Wholesale Quality Pan Head Screw Stainless Steel Screw](https://engineeringhardware.com/product/wholesale-quality-pan-head-screw-stainless-steel-screw/) Pan Head · DIN, GB, SGS/ISO **US$1,200 – 2,160**MOQ 1 ton [![Vodafast Pan Head Machine Screw with Two Washers HDG](https://img.engineeringhardware.com/Vodafast-Pan-Head-Machine-Screw-with-Two-Washers-HDG.webp)](https://engineeringhardware.com/product/vodafast-pan-head-machine-screw-with-two-washers-hdg/) Button, Pan & Round-Head Screws ### [Vodafast Pan Head Machine Screw with Two Washers HDG](https://engineeringhardware.com/product/vodafast-pan-head-machine-screw-with-two-washers-hdg/) Hexagon Head · DIN, GB, ANSI, BSW, JIS, GOST **US$0.0084 – 0.012**MOQ 10,000 pieces [View all Button, Pan & Round-Head Screws →](https://engineeringhardware.com/fastener-products/screws/button-pan-round-head-screws/) [Full product catalog](https://engineeringhardware.com/products/) ## Materials & Grades Select a material class to see the grades we supply it in. Each designation is listed with its ISO/EN, AISI/SAE, JIS and GB equivalents. Stainless Steel38 Carbon Steel66 Alloy Steel41 Bearing Steel5 Spring Steel25 Aluminum and Aluminum Alloys21 Brass17 Bronze11 Copper8 Titanium and Titanium Alloys18 Nickel and Nickel Alloys22 Iron-Nickel and High-Temperature Alloys10 Tool Steel and Specialty Hardened Steel9 Structural and Construction Steel9 ### Stainless Steel #### Austenitic Stainless Steel - A1 AISI 303 · SAE 303 · SUS303 · EN 1.4305 · X8CrNiS18-9 - A2 AISI 304 · SAE 304 · SUS304 · EN 1.4301 · X5CrNi18-10 · 06Cr19Ni10 - 304L AISI 304L · SUS304L · EN 1.4307 · X2CrNi18-9 · 022Cr19Ni10 - 302 AISI 302 · SUS302 · EN 1.4310 - 305 AISI 305 · SUS305 · EN 1.4303 - A4 AISI 316 · SAE 316 · SUS316 · EN 1.4401 · X5CrNiMo17-12-2 · 06Cr17Ni12Mo2 - 316L AISI 316L · SUS316L · EN 1.4404 · X2CrNiMo17-12-2 · 022Cr17Ni12Mo2 - 321 AISI 321 · SUS321 · EN 1.4541 · X6CrNiTi18-10 - 310 / 310S AISI 310 · AISI 310S · SUS310S · EN 1.4845 - 302HQ AISI 302HQ - A3 - A5 - 347 AISI 347 · SUS347 · EN 1.4550 · X6CrNiNb18-10 - 309 / 309S AISI 309 · AISI 309S · SUS309S #### Martensitic Stainless Steel - AISI 410 SUS410 · EN 1.4006 · X12Cr13 · 12Cr13 - AISI 420 SUS420J1 · SUS420J2 · EN 1.4021 · EN 1.4028 · 20Cr13 · 30Cr13 - AISI 431 SUS431 · EN 1.4057 · X17CrNi16-2 - C1 - C3 - C4 - AISI 440A - AISI 440B - AISI 440C SUS440C · EN 1.4125 #### Ferritic Stainless Steel - AISI 430 SUS430 · EN 1.4016 · X6Cr17 · 10Cr17 - F1 - AISI 434 - AISI 444 #### Precipitation-Hardening Stainless Steel - 17-4 PH AISI 630 · UNS S17400 · SUS630 · EN 1.4542 · X5CrNiCuNb16-4 - 15-5 PH UNS S15500 - 17-7 PH UNS S17700 #### Duplex and Super Duplex Stainless Steel - Duplex 2205 UNS S31803 · UNS S32205 · EN 1.4462 - Super Duplex 2507 UNS S32750 · EN 1.4410 - D2 - D4 - D6 - D8 - Lean Duplex 2101 UNS S32101 - Super Duplex S32760 UNS S32760 · EN 1.4501 ### Carbon Steel #### Low-Carbon Steel - SAE 1006 - SAE 1008 - SAE 1010 - SAE 1018 - SAE 1020 - Q195 - Q235 - SAE 1012 - SAE 1015 - Q215 - ML08 - ML08Al - ML10 - ML15 - ML20 - SWRCH6A - SWRCH8A - SWRCH10A - SWRCH12A - SWRCH15A - SWRCH18A #### Medium-Carbon Steel - SAE 1035 - SAE 1045 - S45C - C45 - SAE 1030 - SAE 1040 - SAE 1050 - 30 - 35 - 40 - 45 - 50 - S35C - S40C - S50C - C35 - C40 #### High-Carbon Steel - SAE 1060 - SAE 1070 - 65Mn - SAE 1065 - SAE 1075 - SAE 1080 - SAE 1085 - SAE 1090 - SAE 1095 - 60 - 65 - 70 - 75 - 80 - 85 #### Cold-Heading Steel - SWRCH22A - 10B21 - SWRCH22K - SWRCH25K - SWRCH30K - SWRCH35K - SWRCH40K - ML20Mn - ML25 - ML30 - ML35 - ML40 - 15B25 ### Alloy Steel #### Chromium Steel - 40Cr - 45Cr - AISI 5140 - SAE 5140 - AISI 5120 - SAE 5120 - SCr420 - SCr440 #### Chromium-Molybdenum Steel - 35CrMo - 42CrMo - AISI 4140 - SCM435 - SCM440 - 42CrMo4 - 30CrMo - AISI 4130 - SAE 4130 - SAE 4140 - AISI 4142 - AISI 4145 - SCM415 - SCM420 - SCM445 - EN 1.7220 - EN 1.7225 - 25CrMo4 - 34CrMo4 #### Nickel-Chromium-Molybdenum Steel - AISI 4340 - SAE 4340 - 40CrNiMo - SNCM439 - EN 1.6511 - 36CrNiMo4 #### Boron Alloy Steel - 10B22 - 10B21 - 15B21 - 15B25 - 20MnTiB - 20Mn2B - 35VB - 40MnB ### Bearing Steel #### Bearing Steel - GCr15 - AISI 52100 SAE 52100 · UNS G52986 - SUJ2 - 100Cr6 EN 1.3505 - GCr15SiMn ### Spring Steel #### Carbon Spring Steel - SAE 1065 - SAE 1070 - SAE 1075 - SAE 1080 - SAE 1095 - 65 - 70 - 75 - 80 - 65Mn #### Silicon-Manganese Spring Steel - 60Si2Mn - 60Si2MnA - SUP6 - SUP7 #### Chromium-Vanadium Spring Steel - 50CrVA - SAE 6150 - AISI 6150 - SUP10 #### Stainless Spring Steel - AISI 301 - SUS301 - EN 1.4310 - AISI 302 - AISI 304 - AISI 316 - 17-7 PH ### Aluminum and Aluminum Alloys #### Commercially Pure Aluminum - 1050 - 1060 - 1070 - 1100 #### 2xxx Series Aluminum - 2024 - 2011 - 2014 - 2017 #### 5xxx Series Aluminum - 5052 - 5083 - 5754 #### 6xxx Series Aluminum - 6061 - 6061-T6 - 6063 - 6082 - 6082-T6 #### 7xxx Series Aluminum - 7075 - 7075-T6 - 7005 - 7050 - 7075-T73 ### Brass #### Free-Cutting Brass - C36000 - H62 - HPb59-1 - C3601 - C3602 - C3604 - CuZn36Pb3 - CuZn39Pb3 - EN CW614N - EN CW617N - H65 #### Lead-Free Brass - C69300 - C27450 - CW510L - CW511L #### Naval Brass - C46400 - CuZn39Sn1 ### Bronze #### Silicon Bronze - C65500 - C65100 - C65600 #### Phosphor Bronze - C51000 - C52100 - CuSn6 - CuSn8 #### Aluminum Bronze - C95400 - C95500 - C63000 - CuAl10Ni5Fe4 ### Copper #### Copper - C11000 - T2 - C10100 - C10200 - C12200 - T1 - TU1 - TU2 ### Titanium and Titanium Alloys #### Commercially Pure Titanium - Grade 2 - Grade 1 - Grade 3 - Grade 4 - TA1 - TA2 - TA3 #### Alpha-Beta Titanium Alloys - Grade 5 - Ti-6Al-4V - TC4 - UNS R56400 #### Low-Interstitial Grade - Grade 23 - Ti-6Al-4V ELI - UNS R56407 #### Other Titanium Fastener Alloys - Ti-6Al-6V-2Sn - Ti-6Al-2Sn-4Zr-2Mo - Beta-C titanium - Ti-10V-2Fe-3Al ### Nickel and Nickel Alloys #### Commercially Pure Nickel - Nickel 200 - UNS N02200 - Nickel 201 - UNS N02201 #### Inconel Alloys - Inconel 625 UNS N06625 - Inconel 718 UNS N07718 - Inconel 600 UNS N06600 - Inconel 601 UNS N06601 - Inconel 686 UNS N06686 - Inconel X-750 UNS N07750 #### Monel Alloys - Monel 400 UNS N04400 - Monel K-500 UNS N05500 #### Hastelloy Alloys - Hastelloy C-276 UNS N10276 - Hastelloy C-22 UNS N06022 - Hastelloy B-2 UNS N10665 - Hastelloy B-3 UNS N10675 - Hastelloy X UNS N06002 #### Other Nickel Alloys - Alloy 20 UNS N08020 - Alloy 625 - Alloy 718 - Alloy 825 UNS N08825 - Alloy 925 UNS N09925 ### Iron-Nickel and High-Temperature Alloys #### A286 - A-286 - UNS S66286 - EN 1.4980 #### Invar - Invar 36 - Alloy 36 - UNS K93600 - FeNi36 #### Alloy 42 - Alloy 42 - UNS K94100 - FeNi42 ### Tool Steel and Specialty Hardened Steel #### Tool Steel and Specialty Hardened Steel - AISI D2 - AISI H13 - SKD11 - Cr12MoV - AISI O1 - AISI A2 - AISI S7 - SKD61 - 9CrSi ### Structural and Construction Steel #### Structural and Construction Steel - ASTM A36 - Q235B - Q355B - S355JR - Q235C - Q355C - S235JR - S275JR - S355J2 ## Applications & Industries Where SEMS Screws with Captive Flat Washers are used, and what decides the specification in each case. Stocked from M2.5 to M8. ### Industries that specify SEMS Screws with Captive Flat Washers - **Electrical assembly:** Captive flat-washer screws for panels, terminals and equipment covers. - **Appliance production:** High-volume screwdriving where a separate washer would slow assembly. - **Sheet-metal enclosures:** Removable covers that must retain the washer on the screw. - **Machine guarding:** Service hardware that stays with the cover during removal. - **Steel fabrication:** Bolted connections in frames, enclosures, walkways and weldments, on the bench and on site. - **Energy & infrastructure:** Tower, pipework, switchgear and plant fixings specified for long service life and inspectable joints. ### Typical applications - combining the screw and flat washer into one captive assembly - spreading bearing load while preventing washer loss during service - using a Phillips drive for controlled production installation - selecting the washer outside diameter and thickness with the thread size - clamping two machined faces to a calculated preload - bolting brackets, motors and gearboxes to a frame ### Service conditions to specify against - **Marine and coastal:** Available in A4 (316) stainless for chloride exposure — coastal structures, pool halls, water treatment and deck hardware, where A2 will eventually pit. - **High load:** Supplied in ISO 898-1 property classes, so the joint can be designed to a stated proof load and tightened to a calculated torque rather than by feel. - **Torque and preload:** The joint is designed around bolt tension, so lubrication, coating and the friction coefficient all change the torque figure — state them together. ### Where to use something else - Do not substitute the captive washer for a hardened structural washer in a high-preload joint. - Do not use a machine thread into unthreaded sheet or timber; use a tapping screw, rivet nut or insert made for that parent material. [Full application guide: where SEMS Screws with Captive Flat Washers are used, how to specify them, and the cases they are wrong for](https://engineeringhardware.com/applications/sems-screws-with-captive-flat-washers/) Inside the plant ## Manufactured in our own plant This part is cold-formed, threaded, heat-treated and finished in-house. The stages below are where its class and finish are actually decided. 1. ![Wire rod feeding into a cold heading machine](https://engineeringhardware.com/wp-content/uploads/2026/08/09-wire-rod-feed-cold-heading-machine.webp) 01 **Cold heading** Wire rod is drawn to size and cold-formed into blanks. Forming rather than cutting keeps the grain flow continuous around the head, which is where a bolt is most likely to fail. Head dimensions and under-head radius checked at set-up and per shift. 2. ![Thread rolling machine producing bolt threads](https://engineeringhardware.com/wp-content/uploads/2026/08/03-thread-rolling-machine-bolt-production.webp) 02 **Thread rolling** Threads are rolled between hardened dies rather than cut. Rolled threads are stronger in fatigue than cut threads and hold pitch and flank angle far more consistently across a batch. Go / no-go ring gauges to ISO 965 tolerance class 6g. 3. ![Baskets of bolts staged for heat treatment](https://engineeringhardware.com/wp-content/uploads/2026/08/05-heat-treatment-baskets-black-bolts.webp) 03 **Heat treatment** Quench-and-temper brings carbon and alloy steel to the property class ordered — 8.8, 10.9 or 12.9 — with the furnace charge tracked so a finished lot can be traced back to it. Core hardness and tensile tested per lot to ISO 898-1. 4. ![Zinc plated bolts in a treatment basket](https://engineeringhardware.com/wp-content/uploads/2026/08/23-zinc-plated-bolts-treatment-basket.webp) 04 **Surface treatment** Zinc, zinc-nickel, hot-dip galvanizing, black oxide, phosphate and Dacromet, selected against the service environment rather than against the price list. Coating thickness and neutral salt spray hours to ISO 9227. ## Frequently Asked Questions ### Does ISO 7045 specify the mechanical strength? No. ISO 7045 controls only the geometry of sems screws with captive flat washers. The mechanical strength is set by ISO 898-1 (bolts, screws and studs) or ISO 898-2 (nuts), and the finish by separate documents. ### Can I substitute ISO 7045 for the corresponding DIN standard on a drawing? On modern drawings the ISO standard is the master reference; the older DIN equivalent is a cross-reference. For most dimensional purposes the parts are interchangeable, but check tolerance grades and the head height — these are the most common points of divergence. ### Which edition of ISO 7045 does this table follow? The table reproduces the dimensions we supply sems screws with captive flat washers to. We do not publish an edition year against it, so where the edition is contractually significant, cite the edition you require on the enquiry and we will confirm it against the table before quoting. ### What is ISO 7045? ISO 7045 is "Pan head screws with type H or type Z cross recess — Product grade A". ### How do I request a quotation? Use the technical drawing on this page to pick the exact configuration, then submit it with the quote form. We respond within one business day. ## Related Pages [View the full SEMS Screws with Captive Flat Washers page](https://engineeringhardware.com/fastener/sems-screws-with-captive-flat-washers/) ### More SEMS Screws with Captive Flat Washers Guides