8 catalogued sizes, dimensioned to SAE J514 / ISO 8434-2 (37-degree flared connections). Pick any row and the technical drawing redraws to it.
JIC 37-Degree Flare Fittings to SAE J514 / ISO 8434-2 (37-degree flared connections): the full dimensional table is reproduced below. 8 sizes are held in the table below, and the technical drawing redraws to whichever row you select.
Standard
SAE J514 / ISO 8434-2 (37-degree flared connections)
Catalogued sizes
8
Dimensions are nominal values from the governing standard. Confirm the tolerance class for your application before ordering.
tightening to the flats-from-finger-tight figure rather than by feel
inspecting the cone for scores before assembly
joining and sealing a fluid or air line
adapting between thread forms on a manifold
Service conditions to specify against
Marine and coastal
Available in A4 (316) stainless for chloride exposure — coastal structures, pool halls, water treatment and deck hardware, where A2 will eventually pit.
Where to use something else
Do not mate a 37-degree JIC to a 45-degree SAE flare; they thread together, they look assembled, and the joint leaks under pressure.
Customize the parameters below — every spec field is editable, and the drawing redraws to match the values you choose. Changing the size will snap the other fields to that size's standard values; you can then override any individual value.
Sends the selected values to the quote form below.
Request a Quotation for JIC 37-Degree Flare Fittings
The form below follows the current technical drawing configuration. Change the drawing values above and the request details update automatically.
Every row below is a starting point for the customizer above — pick any size and the drawing will redraw to that row.
Dash size
Tube outside diameter
Thread (UNF)
Cone angle
-04
1/4 in
7/16-20
37 degrees
-05
5/16 in
1/2-20
37 degrees
-06
3/8 in
9/16-18
37 degrees
-08
1/2 in
3/4-16
37 degrees
-10
5/8 in
7/8-14
37 degrees
-12
3/4 in
1-1/16-12
37 degrees
-16
1 in
1-5/16-12
37 degrees
-20
1-1/4 in
1-5/8-12
37 degrees
JIC 37-Degree Flare Fittings are pipe & pneumatic fittings manufactured to SAE J514 / ISO 8434-2 (37-degree flared connections). This page lists the full dimensional range with the key specifications engineers need to select and specify them.
What Are JIC 37-Degree Flare Fittings?
JIC 37-Degree Flare Fittings are pipe & pneumatic fittings defined by SAE J514 / ISO 8434-2 (37-degree flared connections). They are selected by pipe thread size and the dimensional characteristics shown below, and are available in a range of materials and finishes to suit the application and environment.
Materials & Finishes
Common materials include carbon steel (typically zinc plated or hot-dip galvanized), hardened or case-hardened steel where wear matters, and stainless steel A2 (304) or A4 (316) for corrosion resistance. Specify the material, hardness where relevant, and the surface finish appropriate to your application and environment.
Specification Guides
Each size, material and standard of JIC 37-Degree Flare Fittings has its own reference page with the figures for that one configuration.
JIC 37-Degree Flare Fittings are supplied to order. Pricing starts from approximately US$1.40 per piece for standard sizes in carbon steel; final pricing depends on size, material, finish and order quantity (MOQ applies). Submit your exact configuration with the quote form above.
This part is cold-formed, threaded, heat-treated and finished in-house. The stages below are where its class and finish are actually decided.
01
Cold heading
Wire rod is drawn to size and cold-formed into blanks. Forming rather than cutting keeps the grain flow continuous around the head, which is where a bolt is most likely to fail.
Head dimensions and under-head radius checked at set-up and per shift.
02
Thread rolling
Threads are rolled between hardened dies rather than cut. Rolled threads are stronger in fatigue than cut threads and hold pitch and flank angle far more consistently across a batch.
Go / no-go ring gauges to ISO 965 tolerance class 6g.
03
Heat treatment
Quench-and-temper brings carbon and alloy steel to the property class ordered — 8.8, 10.9 or 12.9 — with the furnace charge tracked so a finished lot can be traced back to it.
Core hardness and tensile tested per lot to ISO 898-1.
04
Surface treatment
Zinc, zinc-nickel, hot-dip galvanizing, black oxide, phosphate and Dacromet, selected against the service environment rather than against the price list.
Coating thickness and neutral salt spray hours to ISO 9227.
Frequently Asked Questions
What standard are JIC 37-Degree Flare Fittings manufactured to?
JIC 37-Degree Flare Fittings are manufactured to SAE J514 / ISO 8434-2 (37-degree flared connections). The dimensional values on this page follow that standard.
Which sizes of JIC 37-Degree Flare Fittings does Engineering Hardware supply?
The table on this page lists 8 sizes for JIC 37-Degree Flare Fittings, ranging from -04 to -20. Sizes outside the table can be quoted on request.
In which materials are JIC 37-Degree Flare Fittings supplied?
JIC 37-Degree Flare Fittings are supplied in brass, carbon steel and stainless, with finishes including zinc plating, hot-dip galvanizing and black oxide. Choose material and finish to suit the load and the service environment for JIC 37-Degree Flare Fittings.
How do I request a quotation?
Use the parametric drawing on this page to set the exact configuration (size, material, finish) and click "Request this configuration" — a specialist from Engineering Hardware will respond within one business day.
Need a fastener quote or a spec sheet?Message our engineers on WhatsApp — send a drawing or DIN number and get pricing back fast.Start WhatsApp Chat →
This website uses only necessary and functional cookies to operate, secure, and improve basic website performance.
We do not use advertising cookies, Google Analytics, or cross-site tracking technologies.
Privacy Policy
