Skip to content
info@engineeringhardware.com
WhatsApp
Request a Quote
Clamps & Couplings · Trade series (exhaust clamps) · Application guide

What Are Exhaust U-Bolt and Band Clamps Used For?

Typical applications, the industries that specify exhaust u-bolt and band clamps, and how to choose the right size, material and finish for the joint.

Exhaust U-Bolt and Band Clamps are used for closing a hose, pipe or duct joint by band tension, selected by clamp range rather than by thread size. They are manufactured to Trade series (exhaust clamps), and selection is driven by the size designation, the fit and tolerance the assembly requires, and the service environment.

Primary duty
Closing a hose, pipe or duct joint by band tension, selected by clamp range rather than by thread size
Governing standard
Trade series (exhaust clamps)
Category
Clamps & Couplings

Application notes are general engineering guidance. Verify the property class and any approval requirement against your own design calculation.

What Are Exhaust U-Bolt and Band Clamps Used For? application image

Exhaust U-Bolt and Band Clamps are selected when an assembly calls for closing a hose, pipe or duct joint by band tension, selected by clamp range rather than by thread size. This application guide to the Trade series (exhaust clamps) type covers concrete end-uses, the specification checklist, correct installation, and where an alternative fastener performs better.

Typical Applications for Exhaust U-Bolt and Band Clamps

The most common settings where these are specified:

  • General machine building: fastening covers, brackets, motors and sub-assemblies on production equipment.
  • Maintenance & repair (MRO): a stocked size for servicing existing plant where the original fastener spec must be matched.
  • Fabrication & metalwork: bench and on-site assembly of steel frames, enclosures and weldments.

How to Specify Exhaust U-Bolt and Band Clamps for Your Application

  • Size: Match the size to the mating part — see the dimension table below for each option.
  • Material: Choose the material and finish for the service environment — plated steel for general use, stainless for corrosion resistance.
  • Environment: For damp, coastal or chemical exposure prefer A4/316 stainless or a suitable coating; indoors, plated steel or A2 is usually sufficient.
  • Standard: This product is supplied to Trade series (exhaust clamps). Quoting the standard on your order guarantees interchangeable dimensions between suppliers.

Where Exhaust U-Bolt and Band Clamps Are Not the Right Choice

Match the fastener to the load, environment and whether the joint must be reopened; the wrong class or style is the usual cause of joint failure.

Technical Drawing

Customize the parameters below — every spec field is editable, and the drawing redraws to match the values you choose. Changing the size will snap the other fields to that size's standard values; you can then override any individual value.

Sends the selected values to the quote form below.

Request a Quote

The form below follows the current technical drawing configuration. Change the drawing values above and the request details update automatically.

Request a Quotation

Specification
Business Information

Dimensions & Specifications (Trade series (exhaust clamps))

Clamp typePipe deformationReusableTypical use
U-bolt saddle clampcrushes the pipe at the jointnopermanent slip-joint connection
lap-joint band clampnoneyesserviceable slip joint
butt-joint band clampnoneyesbutted pipe ends without a slip joint
Inside the plant

Manufactured in our own plant

This part is cold-formed, threaded, heat-treated and finished in-house. The stages below are where its class and finish are actually decided.

  1. Wire rod feeding into a cold heading machine
    01

    Cold heading

    Wire rod is drawn to size and cold-formed into blanks. Forming rather than cutting keeps the grain flow continuous around the head, which is where a bolt is most likely to fail.

    Head dimensions and under-head radius checked at set-up and per shift.

  2. Thread rolling machine producing bolt threads
    02

    Thread rolling

    Threads are rolled between hardened dies rather than cut. Rolled threads are stronger in fatigue than cut threads and hold pitch and flank angle far more consistently across a batch.

    Go / no-go ring gauges to ISO 965 tolerance class 6g.

  3. Baskets of bolts staged for heat treatment
    03

    Heat treatment

    Quench-and-temper brings carbon and alloy steel to the property class ordered — 8.8, 10.9 or 12.9 — with the furnace charge tracked so a finished lot can be traced back to it.

    Core hardness and tensile tested per lot to ISO 898-1.

  4. Zinc plated bolts in a treatment basket
    04

    Surface treatment

    Zinc, zinc-nickel, hot-dip galvanizing, black oxide, phosphate and Dacromet, selected against the service environment rather than against the price list.

    Coating thickness and neutral salt spray hours to ISO 9227.

Frequently Asked Questions

What are Exhaust U-Bolt and Band Clamps used for?

Closing a hose, pipe or duct joint by band tension, selected by clamp range rather than by thread size. They are supplied to Trade series (exhaust clamps).

Which industries use Exhaust U-Bolt and Band Clamps?

They are commonly specified in general machine building, maintenance & repair (mro) and fabrication & metalwork, among other sectors.

How do I choose the right size of Exhaust U-Bolt and Band Clamps?

Match the size to the mating part using the dimension table on this page.

Are Exhaust U-Bolt and Band Clamps made to a recognized standard?

Yes — they are manufactured to Trade series (exhaust clamps), so dimensions are interchangeable between suppliers when you quote the standard on your order.

Can I get a quote for Exhaust U-Bolt and Band Clamps in the size and material I need?

Yes. Use the technical drawing and quote form on this page to set the size and options, then send the exact configuration to our team for pricing and lead time.