Skip to content
info@engineeringhardware.com
WhatsApp
Request a Quote
Pins · ISO 8735 · Application guide

What Are Internally Threaded Dowel Pins (ISO 8735) Used For?

Typical applications, the industries that specify internally threaded dowel pins (iso 8735), and how to choose the right size, material and finish for the joint.

Internally Threaded Dowel Pins (ISO 8735) are used for precise location and light shear duty between two parts. They are manufactured to ISO 8735, and selection is driven by the nominal diameter, the fit and tolerance the assembly requires, and the service environment.

Primary duty
Precise location and light shear duty between two parts
Governing standard
ISO 8735
Nominal diameter range
6 mm to 20 mm
Category
Pins

Application notes are general engineering guidance. Verify the property class and any approval requirement against your own design calculation.

What Are Internally Threaded Dowel Pins (ISO 8735) Used For? application image

Internally Threaded Dowel Pins (ISO 8735) are used primarily for precise location and light shear duty between two parts. This page lists the industries and assemblies where they are specified, the selection criteria that matter for each application, installation practice, and the cases where a different fastener type is the correct choice. Parts are supplied to ISO 8735. Stocked across roughly 6 mm to 20 mm, they cover general to heavy-duty work.

Typical Applications for Internally Threaded Dowel Pins (ISO 8735)

The most common settings where these are specified:

  • Maintenance & repair (MRO): a stocked size for servicing existing plant where the original fastener spec must be matched.
  • Fabrication & metalwork: bench and on-site assembly of steel frames, enclosures and weldments.
  • Jigs & fixtures: precise location of tooling plates and locating features.
  • Linkages & hinges: pivot points carrying light shear.
  • Machine alignment: dowelling mating housings so they reassemble in the same position.

How to Specify Internally Threaded Dowel Pins (ISO 8735) for Your Application

  • Size: Select on nominal diameter, then on the hole tolerance and fit class — the fit, not the diameter alone, determines whether the part locates or slips. This product spans 6 mm–20 mm; check the full table below for the exact dimensions of each size.
  • Material: Choose the material and finish for the service environment — plated steel for general use, stainless for corrosion resistance.
  • Environment: For damp, coastal or chemical exposure prefer A4/316 stainless or a suitable coating; indoors, plated steel or A2 is usually sufficient.
  • Standard: This product is supplied to ISO 8735. Quoting the standard on your order guarantees interchangeable dimensions between suppliers.

Installation & Assembly Practice

  • Ream the hole to the specified fit class; a dowel pressed into a drilled-only hole will not locate accurately.
  • Press pins in with steady force rather than hammer blows where possible, and chamfer the hole entry.

Common Selection Mistakes with Internally Threaded Dowel Pins (ISO 8735)

  • Using a dowel pin as a load-carrying shear bolt — dowels locate, they are not sized for sustained shear.
  • Ignoring the fit class: a locational fit and an interference fit need different hole tolerances.

Where Internally Threaded Dowel Pins (ISO 8735) Are Not the Right Choice

Not for carrying significant tensile or repeated heavy shear loads — use a bolt or a keyed joint for that.

Technical Drawing

Customize the parameters below — every spec field is editable, and the drawing redraws to match the values you choose. Changing the size will snap the other fields to that size's standard values; you can then override any individual value.

Sends the selected values to the quote form below.

Request a Quote

The form below follows the current technical drawing configuration. Change the drawing values above and the request details update automatically.

Request a Quotation

Specification
Business Information

Dimensions & Specifications (ISO 8735)

Pin diameter d m6 (mm)Internal threadThread depth (mm)Hole H7 (mm)Common length range (mm)Hardness (HRC)ExtractionReference standard
6M410616~6058-62Threaded pullerISO 8735
8M512820~8058-62Threaded pullerISO 8735
10M6161024~10058-62Threaded pullerISO 8735
12M6201226~12058-62Threaded pullerISO 8735
16M8251630~16058-62Threaded pullerISO 8735
20M10282040~20058-62Threaded pullerISO 8735
Inside the plant

Manufactured in our own plant

This part is cold-formed, threaded, heat-treated and finished in-house. The stages below are where its class and finish are actually decided.

  1. Wire rod feeding into a cold heading machine
    01

    Cold heading

    Wire rod is drawn to size and cold-formed into blanks. Forming rather than cutting keeps the grain flow continuous around the head, which is where a bolt is most likely to fail.

    Head dimensions and under-head radius checked at set-up and per shift.

  2. Thread rolling machine producing bolt threads
    02

    Thread rolling

    Threads are rolled between hardened dies rather than cut. Rolled threads are stronger in fatigue than cut threads and hold pitch and flank angle far more consistently across a batch.

    Go / no-go ring gauges to ISO 965 tolerance class 6g.

  3. Baskets of bolts staged for heat treatment
    03

    Heat treatment

    Quench-and-temper brings carbon and alloy steel to the property class ordered — 8.8, 10.9 or 12.9 — with the furnace charge tracked so a finished lot can be traced back to it.

    Core hardness and tensile tested per lot to ISO 898-1.

  4. Zinc plated bolts in a treatment basket
    04

    Surface treatment

    Zinc, zinc-nickel, hot-dip galvanizing, black oxide, phosphate and Dacromet, selected against the service environment rather than against the price list.

    Coating thickness and neutral salt spray hours to ISO 9227.

Frequently Asked Questions

What are Internally Threaded Dowel Pins (ISO 8735) used for?

Precise location and light shear duty between two parts. They are supplied to ISO 8735.

Which industries use Internally Threaded Dowel Pins (ISO 8735)?

They are commonly specified in machine alignment, general machine building and maintenance & repair (mro), among other sectors.

How do I choose the right size of Internally Threaded Dowel Pins (ISO 8735)?

Select on nominal diameter and on the fit the assembly requires. This product is available from 6 mm to 20 mm; the full dimension table on this page lists each size.

What material should Internally Threaded Dowel Pins (ISO 8735) be for outdoor use?

For damp, coastal or chemical environments specify A4 (316) stainless or a suitably coated steel. For indoor or dry use, A2 (304) stainless or zinc-plated steel is normally adequate.

Can I get a quote for Internally Threaded Dowel Pins (ISO 8735) in the size and material I need?

Yes. Use the technical drawing and quote form on this page to set the size and options, then send the exact configuration to our team for pricing and lead time.