Skip to content
info@engineeringhardware.com
WhatsApp
Request a Quote
Tools · ISO 10664 (hexalobular internal driving feature) · Application guide

What Are Torx Keys (L-Key and T-Handle) Used For?

Typical applications, the industries that specify torx keys (l-key and t-handle), and how to choose the right size, material and finish for the joint.

Torx Keys (L-Key and T-Handle) are used for installing, adjusting or servicing the assembly rather than forming part of it. They are manufactured to ISO 10664 (hexalobular internal driving feature), and selection is driven by the nominal size, the fit and tolerance the assembly requires, and the service environment.

Primary duty
Installing, adjusting or servicing the assembly rather than forming part of it
Governing standard
ISO 10664 (hexalobular internal driving feature)
Nominal size range
T6 to T50
Category
Tools

Application notes are general engineering guidance. Verify the property class and any approval requirement against your own design calculation.

What Are Torx Keys (L-Key and T-Handle) Used For? application image

The primary duty of Torx Keys (L-Key and T-Handle) is installing, adjusting or servicing the assembly rather than forming part of it. Below: the sectors that specify them in volume, the checklist used to select the right size and material for the application, installation notes, and the known limits of the type. Stocked across roughly 6 mm to 50 mm, they cover general to heavy-duty work.

Typical Applications for Torx Keys (L-Key and T-Handle)

The most common settings where these are specified:

  • General machine building: fastening covers, brackets, motors and sub-assemblies on production equipment.
  • Maintenance & repair (MRO): a stocked size for servicing existing plant where the original fastener spec must be matched.
  • Fabrication & metalwork: bench and on-site assembly of steel frames, enclosures and weldments.

How to Specify Torx Keys (L-Key and T-Handle) for Your Application

  • Size: Select on nominal size, and confirm it against the mating feature in the assembly. This product spans 6 mm–50 mm; check the full table below for the exact dimensions of each size.
  • Material: Choose the material and finish for the service environment — plated steel for general use, stainless for corrosion resistance.
  • Environment: For damp, coastal or chemical exposure prefer A4/316 stainless or a suitable coating; indoors, plated steel or A2 is usually sufficient.
  • Standard: This product is supplied to ISO 10664 (hexalobular internal driving feature). Quoting the standard on your order guarantees interchangeable dimensions between suppliers.

Where Torx Keys (L-Key and T-Handle) Are Not the Right Choice

Match the fastener to the load, environment and whether the joint must be reopened; the wrong class or style is the usual cause of joint failure.

Technical Drawing

Customize the parameters below — every spec field is editable, and the drawing redraws to match the values you choose. Changing the size will snap the other fields to that size's standard values; you can then override any individual value.

Sends the selected values to the quote form below.

Request a Quote

The form below follows the current technical drawing configuration. Change the drawing values above and the request details update automatically.

Request a Quotation

Specification
Business Information

Dimensions & Specifications (ISO 10664 (hexalobular internal driving feature))

Torx sizeTypical mating screwFormNotes
T6M2 hexalobular screwL-keyelectronics and instrument assembly
T8M2.5 hexalobular screwL-keyelectronics and instrument assembly
T10M3 hexalobular screwL-key or T-handlegeneral light assembly
T15M3.5 hexalobular screwL-key or T-handlegeneral light assembly
T20M4 hexalobular screwL-key or T-handlegeneral assembly
T25M5 hexalobular screwL-key or T-handlegeneral assembly, decking screws
T27M5 / M6 hexalobular screwL-key or T-handleconstruction screws
T30M6 hexalobular screwL-key or T-handleconstruction and structural screws
T40M8 hexalobular screwL-key or T-handleheavy assembly
T45M10 hexalobular screwL-keyheavy assembly
T50M12 hexalobular screwL-keyheavy assembly
Inside the plant

Manufactured in our own plant

This part is cold-formed, threaded, heat-treated and finished in-house. The stages below are where its class and finish are actually decided.

  1. Wire rod feeding into a cold heading machine
    01

    Cold heading

    Wire rod is drawn to size and cold-formed into blanks. Forming rather than cutting keeps the grain flow continuous around the head, which is where a bolt is most likely to fail.

    Head dimensions and under-head radius checked at set-up and per shift.

  2. Thread rolling machine producing bolt threads
    02

    Thread rolling

    Threads are rolled between hardened dies rather than cut. Rolled threads are stronger in fatigue than cut threads and hold pitch and flank angle far more consistently across a batch.

    Go / no-go ring gauges to ISO 965 tolerance class 6g.

  3. Baskets of bolts staged for heat treatment
    03

    Heat treatment

    Quench-and-temper brings carbon and alloy steel to the property class ordered — 8.8, 10.9 or 12.9 — with the furnace charge tracked so a finished lot can be traced back to it.

    Core hardness and tensile tested per lot to ISO 898-1.

  4. Zinc plated bolts in a treatment basket
    04

    Surface treatment

    Zinc, zinc-nickel, hot-dip galvanizing, black oxide, phosphate and Dacromet, selected against the service environment rather than against the price list.

    Coating thickness and neutral salt spray hours to ISO 9227.

Frequently Asked Questions

What are Torx Keys (L-Key and T-Handle) used for?

Installing, adjusting or servicing the assembly rather than forming part of it. They are supplied to ISO 10664 (hexalobular internal driving feature).

Which industries use Torx Keys (L-Key and T-Handle)?

They are commonly specified in general machine building, maintenance & repair (mro) and fabrication & metalwork, among other sectors.

How do I choose the right size of Torx Keys (L-Key and T-Handle)?

Select on nominal size and on the fit the assembly requires. This product is available from 6 mm to 50 mm; the full dimension table on this page lists each size.

Are Torx Keys (L-Key and T-Handle) made to a recognized standard?

Yes — they are manufactured to ISO 10664 (hexalobular internal driving feature), so dimensions are interchangeable between suppliers when you quote the standard on your order.

Can I get a quote for Torx Keys (L-Key and T-Handle) in the size and material I need?

Yes. Use the technical drawing and quote form on this page to set the size and options, then send the exact configuration to our team for pricing and lead time.