14 catalogued sizes, dimensioned to Industry standard. Pick any row and the technical drawing redraws to it.
Push-In Pneumatic Fittings to Industry standard: the full dimensional table is reproduced below. 14 sizes are held in the table below, and the technical drawing redraws to whichever row you select.
Standard
Industry standard
Catalogued sizes
14
Dimensions are nominal values from the governing standard. Confirm the tolerance class for your application before ordering.
Available in A4 (316) stainless for chloride exposure — coastal structures, pool halls, water treatment and deck hardware, where A2 will eventually pit.
Customize the parameters below — every spec field is editable, and the drawing redraws to match the values you choose. Changing the size will snap the other fields to that size's standard values; you can then override any individual value.
Dimensioned line drawing of 4 Push-In Pneumatic Fittings to Industry standard. Side view and top view, drawn to the dimensions in the table below and redrawn for any size selected.
Thread size
M5x0.8
Flow ref (Nl/min)
80
Max pressure (bar)
10
Pull-out force (N)
70
Notes
Push-in pneumatic fitting for PA/PU tubing
Opens a short step to confirm the exact specification before you enter contact details.
Request a Quotation for Push-In Pneumatic Fittings
Click “Request this configuration” under the drawing to confirm the exact specification, then add your contact details. You can also send the request without a specification — but only an accurate selection gets an accurate quote.
Dimensions & Specifications (Industry standard)
Every row below is a starting point for the customizer above — pick any size and the drawing will redraw to that row.
Tube OD (mm)
Thread size
Flow ref (Nl/min)
Max pressure (bar)
Pull-out force (N)
Reference standard
Notes
4
M5x0.8
80
10
70
ISO 6150
Push-in pneumatic fitting for PA/PU tubing
4
1/8 BSP
80
10
70
ISO 6150
Push-in pneumatic fitting for PA/PU tubing
6
M5x0.8
200
10
120
ISO 6150
Push-in pneumatic fitting for PA/PU tubing
6
1/8 BSP
200
10
120
ISO 6150
Push-in pneumatic fitting for PA/PU tubing
6
1/4 BSP
200
10
120
ISO 6150
Push-in pneumatic fitting for PA/PU tubing
8
1/4 BSP
350
10
180
ISO 6150
Push-in pneumatic fitting for PA/PU tubing
8
3/8 BSP
350
10
180
ISO 6150
Push-in pneumatic fitting for PA/PU tubing
10
1/4 BSP
500
10
250
ISO 6150
Push-in pneumatic fitting for PA/PU tubing
10
3/8 BSP
500
10
250
ISO 6150
Push-in pneumatic fitting for PA/PU tubing
10
1/2 BSP
500
10
250
ISO 6150
Push-in pneumatic fitting for PA/PU tubing
12
3/8 BSP
700
10
350
ISO 6150
Push-in pneumatic fitting for PA/PU tubing
12
1/2 BSP
700
10
350
ISO 6150
Push-in pneumatic fitting for PA/PU tubing
16
1/2 BSP
1200
10
500
ISO 6150
Push-in pneumatic fitting for PA/PU tubing
16
3/4 BSP
1200
10
500
ISO 6150
Push-in pneumatic fitting for PA/PU tubing
Push-In Pneumatic Fittings conform to Industry standard. As pipe & pneumatic fittings, they are specified by the dimensions in the table below; this page also covers materials, finishes and typical uses.
What Are Push-In Pneumatic Fittings?
Push-In Pneumatic Fittings are pipe & pneumatic fittings defined by Industry standard. They are selected by pipe thread size and the dimensional characteristics shown below, and are available in a range of materials and finishes to suit the application and environment.
Materials & Finishes
Common materials include carbon steel (typically zinc plated or hot-dip galvanized), hardened or case-hardened steel where wear matters, and stainless steel A2 (304) or A4 (316) for corrosion resistance. Specify the material, hardness where relevant, and the surface finish appropriate to your application and environment.
Specification Guides
Each size, material and standard of Push-In Pneumatic Fittings has its own reference page with the figures for that one configuration.
Push-In Pneumatic Fittings are supplied to order. Pricing starts from approximately US$0.30 per piece for standard sizes in carbon steel; final pricing depends on size, material, finish and order quantity (MOQ applies). Submit your exact configuration with the quote form above.
Custom manufacturing · Made to drawing
Need a push-in pneumatic fittings outside the standard range?
Dimensions, material, finish and form are specified from the drawing — a pipe & pneumatic fitting outside the standard range is a variation on existing tooling rather than a new design.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
This part is cold-formed, threaded, heat-treated and finished in-house. The stages below are where its class and finish are actually decided.
01
Cold heading
Wire rod is drawn to size and cold-formed into blanks. Forming rather than cutting keeps the grain flow continuous around the head, which is where a bolt is most likely to fail.
Head dimensions and under-head radius checked at set-up and per shift.
02
Thread rolling
Threads are rolled between hardened dies rather than cut. Rolled threads are stronger in fatigue than cut threads and hold pitch and flank angle far more consistently across a batch.
Go / no-go ring gauges to ISO 965 tolerance class 6g.
03
Heat treatment
Quench-and-temper brings carbon and alloy steel to the property class ordered — 8.8, 10.9 or 12.9 — with the furnace charge tracked so a finished lot can be traced back to it.
Core hardness and tensile tested per lot to ISO 898-1.
04
Surface treatment
Zinc, zinc-nickel, hot-dip galvanizing, black oxide, phosphate and Dacromet, selected against the service environment rather than against the price list.
Coating thickness and neutral salt spray hours to ISO 9227.
Video: Push-In Pneumatic Fittings
Third-party video, selected automatically for this topic. It is not produced by Engineering Hardware and is not a specification source — use the tables on this page for dimensional data.
Frequently Asked Questions
Which standard governs Push-In Pneumatic Fittings?
Push-In Pneumatic Fittings are manufactured to Industry standard. The dimensional values on this page follow that standard.
Which sizes of Push-In Pneumatic Fittings does Engineering Hardware supply?
The table on this page lists 14 sizes for Push-In Pneumatic Fittings, ranging from 4 to 16. Sizes outside the table can be quoted on request.
In which materials are Push-In Pneumatic Fittings supplied?
Push-In Pneumatic Fittings are supplied in brass, carbon steel and stainless, with finishes including zinc plating, hot-dip galvanizing and black oxide. Choose material and finish to suit the load and the service environment for Push-In Pneumatic Fittings.
How do I request a quotation?
Use the parametric drawing on this page to set the exact configuration (size, material, finish) and click "Request this configuration" — a specialist from Engineering Hardware will respond within one business day.
Need a fastener quote or a spec sheet?Message our engineers on WhatsApp — send a drawing or DIN number and get pricing back fast.Start WhatsApp Chat →
This website uses only necessary and functional cookies to operate, secure, and improve basic website performance.
We do not use advertising cookies, Google Analytics, or cross-site tracking technologies.
Privacy Policy
