A2 Stainless Steel General Flat Washer combine the dimensional form of GB/T 5782 / ISO 4014 with the material properties of grade ISO 3506 group A2 (304 / 1.4301), commonly supplied A2-70: good general corrosion resistance, largely non-magnetic, service range approx. -200 °C to +400 °C, subject to the property class and the joint. This page summarizes the grade data, its corrosion behavior in service, the comparable grades, and the sizes supplied.
Why Choose A2 Stainless Steel for General Flat Washer — GB/T 5782 / ISO 4014 (Series 008)
The most common stainless group for indoor and general outdoor fasteners. For general flat washer — gb/t 5782 / iso 4014 (series 008), this matters when good general corrosion resistance is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 3506 group A2 (304 / 1.4301), commonly supplied A2-70 |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C, subject to the property class and the joint |
| Corrosion characteristic | Good general corrosion resistance |
Galvanic & Galling Considerations
For stainless general flat washer — gb/t 5782 / iso 4014 (series 008) the compatibility question is galvanic rather than galling: joined to aluminum or galvanized steel in wet service, stainless drives corrosion of the less-noble metal. Isolate with a coating, sleeve or non-conductive washer where the joint sees moisture. Note also that stainless is softer than hardened carbon steel, so where the part carries a wear or shear duty, check the load against the grade before substituting.
Comparable Grades
For General Flat Washer — GB/T 5782 / ISO 4014 (Series 008), the alternative stainless grade is A4 (316). Choose A2 (304) for general use and A4 (316) wherever chlorides are present; the molybdenum in A4 is the whole difference. Remember that stainless is the corrosion answer, not the strength answer — for load, look at class 8.8 or 10.9 instead.
Using Stainless Fasteners in Aluminum
Stainless steel is more noble than aluminum, so with an electrolyte present — rain, condensation, salt spray — the aluminum becomes the anode and corrodes at the joint. Area ratio decides how bad it gets: a small stainless fastener in a large aluminum section is normally acceptable, a large stainless fastener in thin aluminum is not. Where the joint gets wet, isolate the metals with a coated or nylon washer and a sealant, or specify an aluminum or coated fastener instead.
Sizes of General Flat Washer — GB/T 5782 / ISO 4014 (Series 008) Available in A2 Stainless Steel
| For bolt size | Inner diameter d1 (mm) | Outer diameter d2 (mm) | Thickness t (mm) | Reference standard |
|---|---|---|---|---|
| M3 | 3.2 | 7.0 | 0.5 | ISO 7089 / GB/T 97.1 |
| M4 | 4.3 | 9.0 | 0.8 | ISO 7089 / GB/T 97.1 |
| M5 | 5.3 | 10.0 | 1.0 | ISO 7089 / GB/T 97.1 |
| M6 | 6.4 | 12.0 | 1.6 | ISO 7089 / GB/T 97.1 |
| M8 | 8.4 | 16.0 | 1.6 | ISO 7089 / GB/T 97.1 |
| M10 | 10.5 | 20.0 | 2.0 | ISO 7089 / GB/T 97.1 |
| M12 | 13.0 | 24.0 | 2.5 | ISO 7089 / GB/T 97.1 |
| M14 | 15.0 | 28.0 | 2.5 | ISO 7089 / GB/T 97.1 |
| M16 | 17.0 | 30.0 | 3.0 | ISO 7089 / GB/T 97.1 |
| M18 | 19.0 | 34.0 | 3.0 | ISO 7089 / GB/T 97.1 |
| M20 | 21.0 | 37.0 | 3.0 | ISO 7089 / GB/T 97.1 |
| M24 | 25.0 | 44.0 | 4.0 | ISO 7089 / GB/T 97.1 |
| M30 | 31.0 | 56.0 | 4.0 | ISO 7089 / GB/T 97.1 |
| M36 | 37.0 | 66.0 | 5.0 | ISO 7089 / GB/T 97.1 |
Dimensions are independent of the material: every size above is available in A2 Stainless Steel.
Custom manufacturing · Made to drawing
Need this washer in a grade that is not listed?
A2 Stainless Steel is one of the grades the catalog describes. Bore and outside diameter are set by the joint rather than by the bolt, which is why an off-table size is so often the right answer. Made by stamping or punching.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
