A2 Stainless Steel Nylon Insert Hex Lock Nut (Type 2) — GB/T 6182 / ISO 10513 (Series 051) pairs the standard GB/T 6182 / ISO 10513 with a A2 Stainless Steel base material. The sections below cover why engineers select this grade for nylon insert hex lock nut (type 2) — gb/t 6182 / iso 10513 (series 051), its corrosion and temperature behavior, and the sizes available.
Why Choose A2 Stainless Steel for Nylon Insert Hex Lock Nut (Type 2) — GB/T 6182 / ISO 10513 (Series 051)
The most common stainless grade for indoor and general outdoor fasteners. For nylon insert hex lock nut (type 2) — gb/t 6182 / iso 10513 (series 051), this matters when good general corrosion resistance is the primary requirement.
Mechanical & Physical Properties
| Grade designation | A2-70 (304) |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C |
| Corrosion characteristic | Good general corrosion resistance |
Galvanic & Galling Considerations
Two important notes for stainless nylon insert hex lock nut (type 2) — gb/t 6182 / iso 10513 (series 051): (1) stainless can gall on stainless threads under load — use a thread lubricant or anti-galling compound, especially for M6 and below; (2) when joined to aluminum or galvanized steel, stainless can drive galvanic corrosion of the less-noble metal in wet service — isolate with a coating or sleeve where appropriate.
Comparable Grades
For Nylon Insert Hex Lock Nut (Type 2) — GB/T 6182 / ISO 10513 (Series 051), the alternative stainless grade is A4 (316). A2 (304) suits general indoor and outdoor service; A4 (316) adds molybdenum for marine and chloride environments. Where higher strength matters more than corrosion, switch to plated alloy-steel class 8.8 or 10.9.
Sizes of Nylon Insert Hex Lock Nut (Type 2) — GB/T 6182 / ISO 10513 (Series 051) Available in A2 Stainless Steel
| Size | Pitch (mm) | Width across flats s (mm) | Width across corners e (mm) | Total height m (mm) | Reference standard |
|---|---|---|---|---|---|
| M3 | 0.5 | 5.5 | 6.01 | 4.0 | ISO 7040 / DIN 985 |
| M4 | 0.7 | 7.0 | 7.66 | 5.0 | ISO 7040 / DIN 985 |
| M5 | 0.8 | 8.0 | 8.79 | 5.0 | ISO 7040 / DIN 985 |
| M6 | 1.0 | 10.0 | 11.05 | 6.0 | ISO 7040 / DIN 985 |
| M8 | 1.25 | 13.0 | 14.38 | 8.0 | ISO 7040 / DIN 985 |
| M10 | 1.5 | 16.0 | 17.77 | 10.0 | ISO 7040 / DIN 985 |
| M12 | 1.75 | 18.0 | 20.03 | 12.0 | ISO 7040 / DIN 985 |
| M14 | 2.0 | 21.0 | 23.36 | 14.0 | ISO 7040 / DIN 985 |
| M16 | 2.0 | 24.0 | 26.75 | 16.0 | ISO 7040 / DIN 985 |
| M18 | 2.5 | 27.0 | 30.14 | 18.0 | ISO 7040 / DIN 985 |
| M20 | 2.5 | 30.0 | 33.53 | 20.0 | ISO 7040 / DIN 985 |
| M24 | 3.0 | 36.0 | 39.98 | 22.0 | ISO 7040 / DIN 985 |
| M30 | 3.5 | 46.0 | 50.85 | 25.0 | ISO 7040 / DIN 985 |
| M36 | 4.0 | 55.0 | 60.79 | 29.0 | ISO 7040 / DIN 985 |