A2 Stainless Steel Thin Hex Castle Nut are stocked to GB/T 6181 / ISO 4035. The grade provides good general corrosion resistance and is largely non-magnetic; the practical service range is approx. -200 °C to +400 °C. Property data, grade comparison and the full size table follow.
Why Choose A2 Stainless Steel for Thin Hex Castle Nut — GB/T 6181 / ISO 4035 (Series 053)
The most common stainless grade for indoor and general outdoor fasteners. For thin hex castle nut — gb/t 6181 / iso 4035 (series 053), this matters when good general corrosion resistance is the primary requirement.
Mechanical & Physical Properties
| Grade designation | A2-70 (304) |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C |
| Corrosion characteristic | Good general corrosion resistance |
Corrosion Behavior in Service
A2 (304) gives excellent atmospheric and most-water corrosion resistance and is the most common stainless for Thin Hex Castle Nut — GB/T 6181 / ISO 4035 (Series 053) in indoor and general outdoor service. In chloride-bearing environments (marine air, road salt, swimming pools) consider stepping up to A4 (316).
Galvanic & Galling Considerations
Two important notes for stainless thin hex castle nut — gb/t 6181 / iso 4035 (series 053): (1) stainless can gall on stainless threads under load — use a thread lubricant or anti-galling compound, especially for M6 and below; (2) when joined to aluminum or galvanized steel, stainless can drive galvanic corrosion of the less-noble metal in wet service — isolate with a coating or sleeve where appropriate.
Sizes of Thin Hex Castle Nut — GB/T 6181 / ISO 4035 (Series 053) Available in A2 Stainless Steel
| Size | Pitch (mm) | Width across flats s (mm) | Width across corners e (mm) | Total height m (mm) | Slot width (mm) | Reference standard |
|---|---|---|---|---|---|---|
| M3 | 0.5 | 5.5 | 6.01 | 4.0 | 1.2 | ISO 7036 / GB/T 6180 |
| M4 | 0.7 | 7.0 | 7.66 | 5.0 | 1.5 | ISO 7036 / GB/T 6180 |
| M5 | 0.8 | 8.0 | 8.79 | 6.7 | 1.8 | ISO 7036 / GB/T 6180 |
| M6 | 1.0 | 10.0 | 11.05 | 7.7 | 2.0 | ISO 7036 / GB/T 6180 |
| M8 | 1.25 | 13.0 | 14.38 | 9.8 | 2.5 | ISO 7036 / GB/T 6180 |
| M10 | 1.5 | 16.0 | 17.77 | 12.4 | 2.8 | ISO 7036 / GB/T 6180 |
| M12 | 1.75 | 18.0 | 20.03 | 15.8 | 3.5 | ISO 7036 / GB/T 6180 |
| M14 | 2.0 | 21.0 | 23.36 | 17.8 | 4.0 | ISO 7036 / GB/T 6180 |
| M16 | 2.0 | 24.0 | 26.75 | 20.8 | 4.5 | ISO 7036 / GB/T 6180 |
| M18 | 2.5 | 27.0 | 30.14 | 22.5 | 4.5 | ISO 7036 / GB/T 6180 |
| M20 | 2.5 | 30.0 | 33.53 | 24.0 | 5.5 | ISO 7036 / GB/T 6180 |
| M24 | 3.0 | 36.0 | 39.98 | 29.5 | 6.0 | ISO 7036 / GB/T 6180 |
| M30 | 3.5 | 46.0 | 50.85 | 36.0 | 7.0 | ISO 7036 / GB/T 6180 |
| M36 | 4.0 | 55.0 | 60.79 | 43.0 | 8.0 | ISO 7036 / GB/T 6180 |