Tab Lock Washer for Round Nut manufactured in A2 Stainless Steel (ISO 3506 group A2 (304 / 1.4301), commonly supplied A2-70) are dimensioned to GB/T 858. The sections below give the mechanical and physical properties of the grade, its behavior in corrosive and elevated-temperature service, and the full size table.
Why Choose A2 Stainless Steel for Tab Lock Washer for Round Nut — GB/T 858 (Series 073)
The most common stainless group for indoor and general outdoor fasteners. For tab lock washer for round nut — gb/t 858 (series 073), this matters when good general corrosion resistance is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 3506 group A2 (304 / 1.4301), commonly supplied A2-70 |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C, subject to the property class and the joint |
| Corrosion characteristic | Good general corrosion resistance |
Corrosion Behavior in Service
A2 (304) gives excellent atmospheric and most-water corrosion resistance and is the most common stainless for Tab Lock Washer for Round Nut — GB/T 858 (Series 073) in indoor and general outdoor service. In chloride-bearing environments (marine air, road salt, swimming pools) consider stepping up to A4 (316).
Comparable Grades
For Tab Lock Washer for Round Nut — GB/T 858 (Series 073), the alternative stainless grade is A4 (316). The practical dividing line is chlorides: A2 (304) is fine until salt is involved, and A4 (316) exists for the cases where it is — coastal, marine and road-salt service. Neither reaches the strength of a plated class 8.8 or 10.9 fastener.
Using Stainless Fasteners in Aluminum
Expect the aluminum to corrode, not the fastener — stainless sits higher in the galvanic series, so the aluminum is the one that gives up material. A small fastener in a thick section spreads the loss over a large area and is usually fine; a large fastener in thin sheet concentrates it and is not. Keep water out of the joint, or isolate the two metals with a nylon or coated washer and a sealant.
Sizes of Tab Lock Washer for Round Nut — GB/T 858 (Series 073) Available in A2 Stainless Steel
| For shaft / nut size | Inner diameter d1 (mm) | Outer diameter d2 (mm) | Thickness t (mm) | Tab length (mm) | Reference standard |
|---|---|---|---|---|---|
| M10 | 10.5 | 21 | 1.0 | 8 | GB/T 858 |
| M12 | 12.5 | 25 | 1.0 | 9 | GB/T 858 |
| M16 | 16.5 | 30 | 1.0 | 10 | GB/T 858 |
| M20 | 20.5 | 38 | 1.5 | 12 | GB/T 858 |
| M24 | 24.5 | 45 | 1.5 | 14 | GB/T 858 |
| M30 | 30.5 | 55 | 1.5 | 16 | GB/T 858 |
| M36 | 36.5 | 65 | 2.0 | 18 | GB/T 858 |
| M48 | 48.5 | 85 | 2.0 | 20 | GB/T 858 |
| M60 | 60.5 | 105 | 2.5 | 24 | GB/T 858 |
Dimensions are independent of the material: every size above is available in A2 Stainless Steel.
Custom manufacturing · Made to drawing
Need this washer in a grade that is not listed?
A2 Stainless Steel is one of the grades the catalog describes. Bore, outside diameter, thickness, temper and finish are the variables here — there is no thread to specify, so the fit and the bearing area are what the drawing has to pin down. Made by stamping or punching.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
