A2 Stainless Steel Stud Bolt, Double-End are supplied to GB/T 901 / DIN 939. The grade provides good general corrosion resistance and is largely non-magnetic; the practical service range is approx. -200 °C to +400 °C, subject to the property class and the joint. Property data, grade comparison and the full size table follow.
Why Choose A2 Stainless Steel for Stud Bolt, Double-End — GB/T 901 / DIN 939 (Series 091)
The most common stainless group for indoor and general outdoor fasteners. For stud bolt, double-end — gb/t 901 / din 939 (series 091), this matters when good general corrosion resistance is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 3506 group A2 (304 / 1.4301), commonly supplied A2-70 |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C, subject to the property class and the joint |
| Corrosion characteristic | Good general corrosion resistance |
Corrosion Behavior in Service
A2 (304) gives excellent atmospheric and most-water corrosion resistance and is the most common stainless for Stud Bolt, Double-End — GB/T 901 / DIN 939 (Series 091) in indoor and general outdoor service. In chloride-bearing environments (marine air, road salt, swimming pools) consider stepping up to A4 (316).
Galvanic & Galling Considerations
Two important notes for stainless stud bolt, double-end — gb/t 901 / din 939 (series 091): (1) stainless can gall on stainless threads under load — use a thread lubricant or anti-galling compound, especially for M6 and below; (2) when joined to aluminum or galvanized steel, stainless can drive galvanic corrosion of the less-noble metal in wet service — isolate with a coating or sleeve where appropriate.
Using Stainless Fasteners in Aluminum
Stainless steel is more noble than aluminum, so in the presence of an electrolyte — rain, condensation, salt spray — the aluminum becomes the anode and corrodes at the joint. The effect is driven by the area ratio: a small stainless fastener in a large aluminum section is normally acceptable, while a large stainless fastener in thin aluminum is not. Where the joint is wet, isolate the two metals with a coated or nylon washer and a sealant, or specify an aluminum or coated fastener instead.
Sizes of Stud Bolt, Double-End — GB/T 901 / DIN 939 (Series 091) Available in A2 Stainless Steel
| Thread size | Pitch (mm) | Length L (mm) | Engagement depth bm (mm) | Material | Reference standard |
|---|---|---|---|---|---|
| M6 | 1.0 | 50 | 8 | Cl. 8.8 alloy steel | DIN 939 / GB/T 901 |
| M8 | 1.25 | 60 | 10 | Cl. 8.8 alloy steel | DIN 939 / GB/T 901 |
| M10 | 1.5 | 80 | 15 | Cl. 8.8 alloy steel | DIN 939 / GB/T 901 |
| M12 | 1.75 | 100 | 18 | Cl. 8.8 alloy steel | DIN 939 / GB/T 901 |
| M14 | 2.0 | 120 | 21 | Cl. 8.8 alloy steel | DIN 939 / GB/T 901 |
| M16 | 2.0 | 150 | 24 | Cl. 8.8 alloy steel | DIN 939 / GB/T 901 |
| M20 | 2.5 | 180 | 30 | Cl. 8.8 alloy steel | DIN 939 / GB/T 901 |
| M24 | 3.0 | 200 | 36 | Cl. 8.8 alloy steel | DIN 939 / GB/T 901 |
| M30 | 3.5 | 240 | 45 | Cl. 8.8 alloy steel | DIN 939 / GB/T 901 |
| M36 | 4.0 | 280 | 54 | Cl. 8.8 alloy steel | DIN 939 / GB/T 901 |
