Mechanical properties, corrosion behaviour and the full dimensional range for this grade.
A2 Stainless Steel Thrust Bearing are supplied to ISO 3506 group A2 (304 / 1.4301), commonly supplied A2-70. Corrosion behaviour is good general corrosion resistance, the material is largely non-magnetic, and the usable service range is approx. -200 °C to +400 °C, subject to the property class and the joint. In practice this grade is the most common stainless group for indoor and general outdoor fasteners.
Grade
ISO 3506 group A2 (304 / 1.4301), commonly supplied A2-70
Corrosion resistance
Good general corrosion resistance
Magnetic response
Largely non-magnetic
Service temperature
approx. -200 °C to +400 °C, subject to the property class and the joint
Property values are typical for the grade. Certified mechanical test data is available on request for production orders.
Hidden Deck Fasteners Sourcing: Manufacturing, Types & Material Compatibility
A2 Stainless Steel is not a material thrust bearing are supplied in. Thrust Bearing are specified by bore diameter, and this combination does not describe a part that exists.
Need this bearing & bushing in a grade that is not listed?
A2 Stainless Steel is one of the grades the catalog describes. Dimensions, material, finish and form are specified from the drawing — a bearing & bushing outside the standard range is a variation on existing tooling rather than a new design.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
Customize the parameters below — every spec field is editable, and the drawing redraws to match the values you choose. Changing the size will snap the other fields to that size's standard values; you can then override any individual value.
Dimensioned line drawing of 10 Thrust Bearing — ISO / DIN (Series 110). Side view and top view, drawn to the dimensions in the table below and redrawn for any size selected.
Outer diameter D (mm)
24
Total height H (mm)
9
Dynamic axial load Ca (kN)
9.65
Limit speed (rpm)
4000
Opens a short step to confirm the exact specification before you enter contact details.
Request a Quote
Click “Request this configuration” under the drawing to confirm the exact specification, then add your contact details. You can also send the request without a specification — but only an accurate selection gets an accurate quote.
Dimensions & Specifications (ISO / DIN)
Bore d (mm)
Outer diameter D (mm)
Total height H (mm)
Dynamic axial load Ca (kN)
Limit speed (rpm)
Reference standard
10
24
9
9.65
4000
ISO 104 / GB/T 301
15
28
9
11.5
3800
ISO 104 / GB/T 301
20
35
10
17.0
3200
ISO 104 / GB/T 301
25
42
11
22.0
2800
ISO 104 / GB/T 301
30
47
11
27.0
2400
ISO 104 / GB/T 301
40
60
13
42.5
2000
ISO 104 / GB/T 301
50
70
14
52.0
1700
ISO 104 / GB/T 301
60
85
17
70.0
1500
ISO 104 / GB/T 301
80
105
19
93.0
1200
ISO 104 / GB/T 301
Materials & Grades
Select a material class to see the grades we supply it in. Each designation is listed with its ISO/EN, AISI/SAE, JIS and GB equivalents.
Third-party video, selected automatically for this topic. It is not produced by Engineering Hardware and is not a specification source — use the tables on this page for dimensional data.
Inside the plant
Manufactured in our own plant
This part is cold-formed, threaded, heat-treated and finished in-house. The stages below are where its class and finish are actually decided.
01
Cold heading
Wire rod is drawn to size and cold-formed into blanks. Forming rather than cutting keeps the grain flow continuous around the head, which is where a bolt is most likely to fail.
Head dimensions and under-head radius checked at set-up and per shift.
02
Thread rolling
Threads are rolled between hardened dies rather than cut. Rolled threads are stronger in fatigue than cut threads and hold pitch and flank angle far more consistently across a batch.
Go / no-go ring gauges to ISO 965 tolerance class 6g.
03
Heat treatment
Quench-and-temper brings carbon and alloy steel to the property class ordered — 8.8, 10.9 or 12.9 — with the furnace charge tracked so a finished lot can be traced back to it.
Core hardness and tensile tested per lot to ISO 898-1.
04
Surface treatment
Zinc, zinc-nickel, hot-dip galvanizing, black oxide, phosphate and Dacromet, selected against the service environment rather than against the price list.
Coating thickness and neutral salt spray hours to ISO 9227.
Frequently Asked Questions
Is A2 Stainless Steel food-grade?
A2 (304) is widely accepted for food contact in non-chloride environments; A4 (316) is preferred where chlorides are present.
Can A2 Stainless Steel Thrust Bearing — ISO / DIN (Series 110) be used with aluminum?
Yes, but stainless drives mild galvanic corrosion of aluminum in wet service — isolate with a coating, sleeve or paint, or accept the trade-off if the joint is dry and indoor.
What's the service temperature limit for A2 Stainless Steel?
The practical service range is approx. -200 °C to +400 °C, subject to the property class and the joint.
Can A2 Stainless Steel replace plated alloy steel structurally?
Only at the standard strength classes — A2-70 / A4-80 are roughly equivalent to class 7 steel; A4-100 reaches class 8.8. For class 10.9 or 12.9 strength, plated alloy steel is required.
How do I request a quotation?
Use the technical drawing on this page to pick the exact configuration, then submit it with the quote form. We respond within one business day.
This website uses only necessary and functional cookies to operate, secure, and improve basic website performance.
We do not use advertising cookies, Google Analytics, or cross-site tracking technologies.
Privacy Policy
