Mechanical properties, corrosion behaviour and the full dimensional range for this grade.
A2 Stainless Steel Cylindrical Roller Bearing are supplied to ISO 3506 group A2 (304 / 1.4301), commonly supplied A2-70. Corrosion behaviour is good general corrosion resistance, the material is largely non-magnetic, and the usable service range is approx. -200 °C to +400 °C, subject to the property class and the joint. In practice this grade is the most common stainless group for indoor and general outdoor fasteners.
Grade
ISO 3506 group A2 (304 / 1.4301), commonly supplied A2-70
Corrosion resistance
Good general corrosion resistance
Magnetic response
Largely non-magnetic
Service temperature
approx. -200 °C to +400 °C, subject to the property class and the joint
Property values are typical for the grade. Certified mechanical test data is available on request for production orders.
Hidden Deck Fasteners Sourcing: Manufacturing, Types & Material Compatibility
A2 Stainless Steel is not a material cylindrical roller bearing are supplied in. Cylindrical Roller Bearing are specified by bore diameter, and this combination does not describe a part that exists.
Need this bearing & bushing in a grade that is not listed?
A2 Stainless Steel is one of the grades the catalog describes. Dimensions, material, finish and form are specified from the drawing — a bearing & bushing outside the standard range is a variation on existing tooling rather than a new design.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
Customize the parameters below — every spec field is editable, and the drawing redraws to match the values you choose. Changing the size will snap the other fields to that size's standard values; you can then override any individual value.
Dimensioned line drawing of 20 Cylindrical Roller Bearing — ISO / DIN (Series 112). Side view and top view, drawn to the dimensions in the table below and redrawn for any size selected.
Outer diameter D (mm)
47
Width B (mm)
14
Dynamic load C (kN)
28.4
Limit speed (rpm)
11000
Opens a short step to confirm the exact specification before you enter contact details.
Request a Quote
Click “Request this configuration” under the drawing to confirm the exact specification, then add your contact details. You can also send the request without a specification — but only an accurate selection gets an accurate quote.
Dimensions & Specifications (ISO / DIN)
Bore d (mm)
Outer diameter D (mm)
Width B (mm)
Dynamic load C (kN)
Limit speed (rpm)
Reference standard
20
47
14
28.4
11000
ISO 246 / GB/T 283
25
52
15
33.5
10000
ISO 246 / GB/T 283
30
62
16
49.5
8500
ISO 246 / GB/T 283
35
72
17
67.0
7500
ISO 246 / GB/T 283
40
80
18
78.0
6700
ISO 246 / GB/T 283
50
90
20
93.0
6000
ISO 246 / GB/T 283
60
110
22
138
5000
ISO 246 / GB/T 283
75
130
25
180
4300
ISO 246 / GB/T 283
90
160
30
238
3600
ISO 246 / GB/T 283
Materials & Grades
Select a material class to see the grades we supply it in. Each designation is listed with its ISO/EN, AISI/SAE, JIS and GB equivalents.
Third-party video, selected automatically for this topic. It is not produced by Engineering Hardware and is not a specification source — use the tables on this page for dimensional data.
Inside the plant
Manufactured in our own plant
This part is cold-formed, threaded, heat-treated and finished in-house. The stages below are where its class and finish are actually decided.
01
Cold heading
Wire rod is drawn to size and cold-formed into blanks. Forming rather than cutting keeps the grain flow continuous around the head, which is where a bolt is most likely to fail.
Head dimensions and under-head radius checked at set-up and per shift.
02
Thread rolling
Threads are rolled between hardened dies rather than cut. Rolled threads are stronger in fatigue than cut threads and hold pitch and flank angle far more consistently across a batch.
Go / no-go ring gauges to ISO 965 tolerance class 6g.
03
Heat treatment
Quench-and-temper brings carbon and alloy steel to the property class ordered — 8.8, 10.9 or 12.9 — with the furnace charge tracked so a finished lot can be traced back to it.
Core hardness and tensile tested per lot to ISO 898-1.
04
Surface treatment
Zinc, zinc-nickel, hot-dip galvanizing, black oxide, phosphate and Dacromet, selected against the service environment rather than against the price list.
Coating thickness and neutral salt spray hours to ISO 9227.
Frequently Asked Questions
Can A2 Stainless Steel replace plated alloy steel structurally?
Only at the standard strength classes — A2-70 / A4-80 are roughly equivalent to class 7 steel; A4-100 reaches class 8.8. For class 10.9 or 12.9 strength, plated alloy steel is required.
Are A2 Stainless Steel Cylindrical Roller Bearing — ISO / DIN (Series 112) magnetic?
A2 Stainless Steel Cylindrical Roller Bearing — ISO / DIN (Series 112) are largely non-magnetic.
What corrosion resistance do A2 Stainless Steel Cylindrical Roller Bearing — ISO / DIN (Series 112) offer?
A2 Stainless Steel Cylindrical Roller Bearing — ISO / DIN (Series 112) provide good general corrosion resistance with a service range of approx. -200 °C to +400 °C, subject to the property class and the joint.
Should I choose A2 Stainless Steel or A4 (316) for Cylindrical Roller Bearing — ISO / DIN (Series 112)?
For Cylindrical Roller Bearing — ISO / DIN (Series 112), A2 Stainless Steel suits general indoor and outdoor use; A4 (316) is preferred for marine, coastal and chemical environments. Choose by corrosion exposure first.
How do I request a quotation?
Use the technical drawing on this page to pick the exact configuration, then submit it with the quote form. We respond within one business day.
Need a fastener quote or a spec sheet?Message our engineers on WhatsApp — send a drawing or DIN number and get pricing back fast.Start WhatsApp Chat →
This website uses only necessary and functional cookies to operate, secure, and improve basic website performance.
We do not use advertising cookies, Google Analytics, or cross-site tracking technologies.
Privacy Policy
