Skip to content

Bearings & Bushings · ISO / DIN

A2 Stainless Steel Deep Groove Ball Bearing — ISO / DIN (Series 129)

When Deep Groove Ball Bearing — ISO / DIN (Series 129) are required in A2 Stainless Steel, the alternative grades and the trade-offs between them matter as much as the dimensions. This page covers both, plus mechanical and corrosion data.

Why Choose A2 Stainless Steel for Deep Groove Ball Bearing — ISO / DIN (Series 129)

The most common stainless grade for indoor and general outdoor fasteners. For deep groove ball bearing — iso / din (series 129), this matters when good general corrosion resistance is the primary requirement.

Mechanical & Physical Properties

Grade designationA2-70 (304)
Magnetic responseLargely non-magnetic
Service temperatureapprox. -200 °C to +400 °C
Corrosion characteristicGood general corrosion resistance

Corrosion Behavior in Service

A2 (304) gives excellent atmospheric and most-water corrosion resistance and is the most common stainless for Deep Groove Ball Bearing — ISO / DIN (Series 129) in indoor and general outdoor service. In chloride-bearing environments (marine air, road salt, swimming pools) consider stepping up to A4 (316).

Comparable Grades

For Deep Groove Ball Bearing — ISO / DIN (Series 129), the alternative stainless grade is A4 (316). A2 (304) suits general indoor and outdoor service; A4 (316) adds molybdenum for marine and chloride environments. Where higher strength matters more than corrosion, switch to plated alloy-steel class 8.8 or 10.9.

Sizes of Deep Groove Ball Bearing — ISO / DIN (Series 129) Available in A2 Stainless Steel

Bore d (mm)Outer diameter D (mm)Width B (mm)Dynamic load C (kN)Limit speed (rpm)Reference standard
103095.132000ISO 15 / GB/T 276
1232106.9528000ISO 15 / GB/T 276
1535117.6524000ISO 15 / GB/T 276
1740129.5622000ISO 15 / GB/T 276
20471412.718000ISO 15 / GB/T 276
25521514.016000ISO 15 / GB/T 276
30621619.513000ISO 15 / GB/T 276
35721725.511000ISO 15 / GB/T 276
40801830.710000ISO 15 / GB/T 276
45851933.29500ISO 15 / GB/T 276
50902035.19000ISO 15 / GB/T 276
601102252.77500ISO 15 / GB/T 276

Technical Drawing

Customize the parameters below — every spec field is editable, and the drawing redraws to match the values you choose. Changing the size will snap the other fields to that size's standard values; you can then override any individual value.

Sends the selected values to the quote form below.

Request a Quote

Adjust the parameters in the drawing above and click "Request this configuration" to send the exact specification straight to this form.

Request a Quotation

Specification
Business Information

Dimensions & Specifications (ISO / DIN)

Bore d (mm)Outer diameter D (mm)Width B (mm)Dynamic load C (kN)Limit speed (rpm)Reference standard
103095.132000ISO 15 / GB/T 276
1232106.9528000ISO 15 / GB/T 276
1535117.6524000ISO 15 / GB/T 276
1740129.5622000ISO 15 / GB/T 276
20471412.718000ISO 15 / GB/T 276
25521514.016000ISO 15 / GB/T 276
30621619.513000ISO 15 / GB/T 276
35721725.511000ISO 15 / GB/T 276
40801830.710000ISO 15 / GB/T 276
45851933.29500ISO 15 / GB/T 276
50902035.19000ISO 15 / GB/T 276
601102252.77500ISO 15 / GB/T 276

Frequently Asked Questions

Can A2 Stainless Steel Deep Groove Ball Bearing — ISO / DIN (Series 129) gall during installation?

Yes — stainless on stainless is prone to thread galling under load, especially at smaller sizes. Use an anti-galling lubricant or wax thread compound, and slow the tightening rate where possible.

Is A2 Stainless Steel food-grade?

A2 (304) is widely accepted for food contact in non-chloride environments; A4 (316) is preferred where chlorides are present.

Can A2 Stainless Steel Deep Groove Ball Bearing — ISO / DIN (Series 129) be used with aluminum?

Yes, but stainless drives mild galvanic corrosion of aluminum in wet service — isolate with a coating, sleeve or paint, or accept the trade-off if the joint is dry and indoor.

What's the service temperature limit for A2 Stainless Steel?

The practical service range is approx. -200 °C to +400 °C.

How do I request a quotation?

Use the technical drawing on this page to pick the exact configuration, then submit it with the quote form. We respond within one business day.