A2 Stainless Steel Phillips Pan Head Wood Screws, Metric are supplied to DIN 7996. The grade provides good general corrosion resistance and is largely non-magnetic; the practical service range is approx. -200 °C to +400 °C, subject to the property class and the joint. Property data, grade comparison and the full size table follow.
Why Choose A2 Stainless Steel for Phillips Pan Head Wood Screws, Metric
The most common stainless group for indoor and general outdoor fasteners. For phillips pan head wood screws, metric, this matters when good general corrosion resistance is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 3506 group A2 (304 / 1.4301), commonly supplied A2-70 |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C, subject to the property class and the joint |
| Corrosion characteristic | Good general corrosion resistance |
Corrosion Behavior in Service
A2 (304) gives excellent atmospheric and most-water corrosion resistance and is the most common stainless for Phillips Pan Head Wood Screws, Metric in indoor and general outdoor service. In chloride-bearing environments (marine air, road salt, swimming pools) consider stepping up to A4 (316).
Galvanic & Galling Considerations
Two important notes for stainless phillips pan head wood screws, metric: (1) stainless can gall on stainless threads under load — use a thread lubricant or anti-galling compound, especially for M6 and below; (2) when joined to aluminum or galvanized steel, stainless can drive galvanic corrosion of the less-noble metal in wet service — isolate with a coating or sleeve where appropriate.
Using Stainless Fasteners in Aluminum
The galvanic couple here runs the wrong way: aluminum is the less noble metal, so it corrodes and the fastener does not. What governs the rate is the ratio of areas — a large anode and a small cathode is a tolerable combination, the reverse concentrates the attack into thin material around the hole. An isolating washer plus sealant breaks the circuit; where that is impractical, match the fastener to the substrate.
Sizes of Phillips Pan Head Wood Screws, Metric Available in A2 Stainless Steel
| Size | Head diameter dk (mm) | Head height k (mm) | da (mm) | r (mm) | d3 (mm) | Pitch P (mm) | Cross recess size | m (mm) | e (mm) | Length range l (mm) | Reference standard |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 2 mm | 4 | 1.4 | 2.8 | 1.6 | 1.4 | 0.9 | 0 | 2.1 | 0.75 | 11~13 | DIN 7996 |
| 2.5 mm | 5 | 1.7 | 3.3 | 2.0 | 1.7 | 1.1 | 1 | 2.3 | 0.85 | 10~30 | DIN 7996 |
| 3 mm | 6 | 2.1 | 3.8 | 2.4 | 2.1 | 1.35 | 1 | 2.7 | 1.3 | 10~40 | DIN 7996 |
| 3.5 mm | 7 | 2.35 | 4.3 | 2.8 | 2.4 | 1.6 | 2 | 3.7 | 1.22 | 10~45 | DIN 7996 |
| 4 mm | 8 | 2.8 | 5.0 | 3.2 | 2.8 | 1.8 | 2 | 4.1 | 1.62 | 12~50 | DIN 7996 |
| 4.5 mm | 9 | 3.1 | 5.5 | 3.6 | 3.1 | 2.0 | 2 | 4.4 | 1.88 | 16~60 | DIN 7996 |
| 5 mm | 10 | 3.5 | 6.0 | 4.0 | 3.5 | 2.2 | 2 | 4.8 | 2.28 | 16~80 | DIN 7996 |
| 5.5 mm | 11 | 3.8 | 6.6 | 4.4 | 3.5 | 2.2 | 2 | 4.8 | 2.28 | 11~13 | DIN 7996 |
| 6 mm | 12 | 4.2 | 7.2 | 4.8 | 4.2 | 2.6 | 3 | 6.6 | 2.82 | 40~80 | DIN 7996 |
| 7 mm | 14 | 4.9 | 8.2 | 5.6 | 4.9 | 3.2 | 3 | 7.3 | 3.52 | 11~13 | DIN 7996 |
| 8 mm | 16 | 5.6 | 10.2 | 6.4 | 5.6 | 3.6 | 4 | 8.8 | 3.93 | 11~13 | DIN 7996 |
Dimensions are independent of the material: every size above is available in A2 Stainless Steel.
Custom manufacturing · Made to drawing
Need this screw in a grade that is not listed?
A2 Stainless Steel is one of the grades the catalog describes. A non-standard screw is quoted from the drawing; where one already exists in the catalog, the special is usually a variation on its tooling. Made by cold heading or warm forging.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
