Specifying Fender Washers in A2 Stainless Steel pairs the dimensional form of Fender Washers (DIN 9021) with the engineering properties of A2 Stainless Steel. This page explains when to choose the grade, how it behaves in service, and which grades to compare it against.
Why Choose A2 Stainless Steel for Fender Washers
The most common stainless grade for indoor and general outdoor fasteners. For fender washers, this matters when good general corrosion resistance is the primary requirement.
Mechanical & Physical Properties
| Grade designation | A2-70 (304) |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C |
| Corrosion characteristic | Good general corrosion resistance |
Galvanic & Galling Considerations
Two important notes for stainless fender washers: (1) stainless can gall on stainless threads under load — use a thread lubricant or anti-galling compound, especially for M6 and below; (2) when joined to aluminum or galvanized steel, stainless can drive galvanic corrosion of the less-noble metal in wet service — isolate with a coating or sleeve where appropriate.
Comparable Grades
For Fender Washers, the alternative stainless grade is A4 (316). A2 (304) suits general indoor and outdoor service; A4 (316) adds molybdenum for marine and chloride environments. Where higher strength matters more than corrosion, switch to plated alloy-steel class 8.8 or 10.9.
Sizes of Fender Washers Available in A2 Stainless Steel
| For bolt size | Inner diameter d1 min (mm) | Outer diameter d2 max (mm) | Thickness h (mm) | Reference standard | Notes |
|---|---|---|---|---|---|
| M3 | 3.2 | 9.0 | 0.8 | DIN 9021 / ISO 7093 | Oversized OD for bearing on soft materials |
| M4 | 4.3 | 12.0 | 1.0 | DIN 9021 / ISO 7093 | Oversized OD for bearing on soft materials |
| M5 | 5.3 | 15.0 | 1.2 | DIN 9021 / ISO 7093 | Oversized OD for bearing on soft materials |
| M6 | 6.4 | 18.0 | 1.6 | DIN 9021 / ISO 7093 | Oversized OD for bearing on soft materials |
| M8 | 8.4 | 24.0 | 2.0 | DIN 9021 / ISO 7093 | Oversized OD for bearing on soft materials |
| M10 | 10.5 | 30.0 | 2.5 | DIN 9021 / ISO 7093 | Oversized OD for bearing on soft materials |
| M12 | 13.0 | 37.0 | 3.0 | DIN 9021 / ISO 7093 | Oversized OD for bearing on soft materials |
| M14 | 15.0 | 44.0 | 3.0 | DIN 9021 / ISO 7093 | Oversized OD for bearing on soft materials |
| M16 | 17.0 | 50.0 | 3.0 | DIN 9021 / ISO 7093 | Oversized OD for bearing on soft materials |
| M20 | 21.0 | 60.0 | 4.0 | DIN 9021 / ISO 7093 | Oversized OD for bearing on soft materials |
| M24 | 25.0 | 72.0 | 5.0 | DIN 9021 / ISO 7093 | Oversized OD for bearing on soft materials |
| M30 | 31.0 | 90.0 | 6.0 | DIN 9021 / ISO 7093 | Oversized OD for bearing on soft materials |
| M36 | 37.0 | 110.0 | 8.0 | DIN 9021 / ISO 7093 | Oversized OD for bearing on soft materials |