When Lag Screws (Hex Wood Screws) are required in A2 Stainless Steel, the alternative grades and the trade-offs between them matter as much as the dimensions. This page covers both, plus mechanical and corrosion data.
Why Choose A2 Stainless Steel for Lag Screws (Hex Wood Screws)
The most common stainless grade for indoor and general outdoor fasteners. For lag screws (hex wood screws), this matters when good general corrosion resistance is the primary requirement.
Mechanical & Physical Properties
| Grade designation | A2-70 (304) |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C |
| Corrosion characteristic | Good general corrosion resistance |
Corrosion Behavior in Service
A2 (304) gives excellent atmospheric and most-water corrosion resistance and is the most common stainless for Lag Screws (Hex Wood Screws) in indoor and general outdoor service. In chloride-bearing environments (marine air, road salt, swimming pools) consider stepping up to A4 (316).
Galvanic & Galling Considerations
Two important notes for stainless lag screws (hex wood screws): (1) stainless can gall on stainless threads under load — use a thread lubricant or anti-galling compound, especially for M6 and below; (2) when joined to aluminum or galvanized steel, stainless can drive galvanic corrosion of the less-noble metal in wet service — isolate with a coating or sleeve where appropriate.
Sizes of Lag Screws (Hex Wood Screws) Available in A2 Stainless Steel
| Nominal diameter (mm) | Pitch (mm) | Width across flats s (mm) | Head height k (mm) | Pilot/guide hole (mm) | Common length range (mm) | Reference standard | Notes |
|---|---|---|---|---|---|---|---|
| 5 | 2.0 | 8.0 | 3.5 | 3.0 | 25~100 | DIN 571 | Wood screw, self-tapping point |
| 6 | 2.5 | 10.0 | 4.0 | 4.0 | 30~150 | DIN 571 | Wood screw, self-tapping point |
| 8 | 3.0 | 13.0 | 5.5 | 5.0 | 40~200 | DIN 571 | Wood screw, self-tapping point |
| 10 | 3.5 | 16.0 | 6.5 | 7.0 | 50~250 | DIN 571 | Wood screw, self-tapping point |
| 12 | 4.0 | 18.0 | 7.5 | 8.5 | 60~300 | DIN 571 | Wood screw, self-tapping point |
| 14 | 4.0 | 21.0 | 9.0 | 10.0 | 60~300 | DIN 571 | Wood screw, self-tapping point |
| 16 | 4.5 | 24.0 | 10.0 | 11.5 | 80~300 | DIN 571 | Wood screw, self-tapping point |
| 18 | 5.0 | 27.0 | 11.5 | 13.0 | 80~300 | DIN 571 | Wood screw, self-tapping point |
| 20 | 5.0 | 30.0 | 12.5 | 14.5 | 100~300 | DIN 571 | Wood screw, self-tapping point |
| 22 | 5.5 | 32.0 | 14.0 | 16.0 | 100~300 | DIN 571 | Wood screw, self-tapping point |
| 24 | 6.0 | 36.0 | 15.0 | 17.5 | 100~300 | DIN 571 | Wood screw, self-tapping point |