Material specification page for button head socket screws in A4 Stainless Steel. Covers the grade designation (ISO 3506 group A4 (316 / 1.4401), commonly supplied A4-80), corrosion and magnetic behavior, comparable grades and their trade-offs, and the sizes available to ISO 7380.
Why Choose A4 Stainless Steel for Button Head Socket Screws
Specified for marine, coastal and chemical applications. For button head socket screws, this matters when superior, including marine and chloride environments is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 3506 group A4 (316 / 1.4401), commonly supplied A4-80 |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C, subject to the property class and the joint |
| Corrosion characteristic | Superior, including marine and chloride environments |
Corrosion Behavior in Service
A4 (316) adds 2–3% molybdenum to the A2 (304) composition, which dramatically improves resistance to chloride-pitting corrosion. For Button Head Socket Screws in marine, coastal, swimming-pool or food-processing environments, A4 is the default selection.
Comparable Grades
For Button Head Socket Screws, the alternative stainless grade is A2 (304). A2 (304) covers general indoor and outdoor service. A4 (316) adds molybdenum, which is what buys the chloride resistance for marine and de-icing-salt exposure. Where strength matters more than corrosion, plated alloy steel in class 8.8 or 10.9 is the swap to make.
Using Stainless Fasteners in Aluminum
Stainless steel is more noble than aluminum, so with an electrolyte present — rain, condensation, salt spray — the aluminum becomes the anode and corrodes at the joint. Area ratio decides how bad it gets: a small stainless fastener in a large aluminum section is normally acceptable, a large stainless fastener in thin aluminum is not. Where the joint gets wet, isolate the metals with a coated or nylon washer and a sealant, or specify an aluminum or coated fastener instead.
Sizes of Button Head Socket Screws Available in A4 Stainless Steel
| Size | Pitch (mm) | Head diameter dk (mm) | Head height k (mm) | Hex socket s (mm) | Reference standard |
|---|---|---|---|---|---|
| M3 | 0.5 | 5.7 | 1.65 | 2.0 | ISO 7380-1 / DIN 7380 |
| M4 | 0.7 | 7.6 | 2.2 | 2.5 | ISO 7380-1 / DIN 7380 |
| M5 | 0.8 | 9.5 | 2.75 | 3.0 | ISO 7380-1 / DIN 7380 |
| M6 | 1.0 | 10.5 | 3.3 | 4.0 | ISO 7380-1 / DIN 7380 |
| M8 | 1.25 | 14.0 | 4.4 | 5.0 | ISO 7380-1 / DIN 7380 |
| M10 | 1.5 | 17.5 | 5.5 | 6.0 | ISO 7380-1 / DIN 7380 |
| M12 | 1.75 | 21.0 | 6.6 | 8.0 | ISO 7380-1 / DIN 7380 |
| M14 | 2.0 | 24.5 | 7.7 | 10.0 | ISO 7380-1 / DIN 7380 |
| M16 | 2.0 | 28.0 | 8.8 | 10.0 | ISO 7380-1 / DIN 7380 |
| M20 | 2.5 | 35.0 | 11.0 | 12.0 | ISO 7380-1 / DIN 7380 |
Dimensions are independent of the material: every size above is available in A4 Stainless Steel.
Custom manufacturing · Made to drawing
Need this screw in a grade that is not listed?
A4 Stainless Steel is one of the grades the catalog describes. Where the standard stops, the drawing takes over: fine pitches, left-hand threads, partial threading, and property classes above the catalogued grade where material and heat treatment allow. Made by cold heading or warm forging.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
