A4 Stainless Steel Hex Head Bolt are supplied to GB/T 5782 / ISO 4014. The grade provides superior, including marine and chloride environments and is largely non-magnetic; the practical service range is approx. -200 °C to +400 °C, subject to the property class and the joint. Property data, grade comparison and the full size table follow.
Why Choose A4 Stainless Steel for Hex Head Bolt — GB/T 5782 / ISO 4014 (Series 001)
Specified for marine, coastal and chemical applications. For hex head bolt — gb/t 5782 / iso 4014 (series 001), this matters when superior, including marine and chloride environments is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 3506 group A4 (316 / 1.4401), commonly supplied A4-80 |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C, subject to the property class and the joint |
| Corrosion characteristic | Superior, including marine and chloride environments |
Corrosion Behavior in Service
A4 (316) adds 2–3% molybdenum to the A2 (304) composition, which dramatically improves resistance to chloride-pitting corrosion. For Hex Head Bolt — GB/T 5782 / ISO 4014 (Series 001) in marine, coastal, swimming-pool or food-processing environments, A4 is the default selection.
Galvanic & Galling Considerations
Two important notes for stainless hex head bolt — gb/t 5782 / iso 4014 (series 001): (1) stainless can gall on stainless threads under load — use a thread lubricant or anti-galling compound, especially for M6 and below; (2) when joined to aluminum or galvanized steel, stainless can drive galvanic corrosion of the less-noble metal in wet service — isolate with a coating or sleeve where appropriate.
Using Stainless Fasteners in Aluminum
Stainless steel is more noble than aluminum, so in the presence of an electrolyte — rain, condensation, salt spray — the aluminum becomes the anode and corrodes at the joint. The effect is driven by the area ratio: a small stainless fastener in a large aluminum section is normally acceptable, while a large stainless fastener in thin aluminum is not. Where the joint is wet, isolate the two metals with a coated or nylon washer and a sealant, or specify an aluminum or coated fastener instead.
Sizes of Hex Head Bolt — GB/T 5782 / ISO 4014 (Series 001) Available in A4 Stainless Steel
| Size | Pitch (mm) | Nominal diameter d (mm) | Length L (mm) | Width across flats s (mm) | Width across corners e (mm) | Head height k (mm) |
|---|---|---|---|---|---|---|
| M3 | 0.5 | 3 | 20 | 5.5 | 6.01 | 2.0 |
| M4 | 0.7 | 4 | 25 | 7.0 | 7.66 | 2.8 |
| M5 | 0.8 | 5 | 30 | 8.0 | 8.79 | 3.5 |
| M6 | 1.0 | 6 | 40 | 10.0 | 11.05 | 4.0 |
| M8 | 1.25 | 8 | 50 | 13.0 | 14.38 | 5.3 |
| M10 | 1.5 | 10 | 60 | 16.0 | 17.77 | 6.4 |
| M12 | 1.75 | 12 | 80 | 18.0 | 20.03 | 7.5 |
| M14 | 2.0 | 14 | 80 | 21.0 | 23.36 | 8.8 |
| M16 | 2.0 | 16 | 100 | 24.0 | 26.75 | 10.0 |
| M18 | 2.5 | 18 | 100 | 27.0 | 30.14 | 11.5 |
| M20 | 2.5 | 20 | 120 | 30.0 | 33.53 | 12.5 |
| M24 | 3.0 | 24 | 150 | 36.0 | 39.98 | 15.0 |
| M30 | 3.5 | 30 | 180 | 46.0 | 50.85 | 18.7 |
| M36 | 4.0 | 36 | 200 | 55.0 | 60.79 | 22.5 |
