A4 Stainless Steel (ISO 3506 group A4 (316 / 1.4401), commonly supplied A4-80) is specified for marine, coastal and chemical applications. When castellated hex nut are specified in this grade, the dimensions remain per GB/T 6180 / ISO 7036; the material determines corrosion behavior (superior, including marine and chloride environments) and the service temperature range (approx. -200 °C to +400 °C, subject to the property class and the joint). Both are covered below with the size table.
Why Choose A4 Stainless Steel for Castellated Hex Nut — GB/T 6180 / ISO 7036 (Series 048)
Specified for marine, coastal and chemical applications. For castellated hex nut — gb/t 6180 / iso 7036 (series 048), this matters when superior, including marine and chloride environments is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 3506 group A4 (316 / 1.4401), commonly supplied A4-80 |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C, subject to the property class and the joint |
| Corrosion characteristic | Superior, including marine and chloride environments |
Galvanic & Galling Considerations
Two important notes for stainless castellated hex nut — gb/t 6180 / iso 7036 (series 048): (1) stainless can gall on stainless threads under load — use a thread lubricant or anti-galling compound, especially for M6 and below; (2) when joined to aluminum or galvanized steel, stainless can drive galvanic corrosion of the less-noble metal in wet service — isolate with a coating or sleeve where appropriate.
Comparable Grades
For Castellated Hex Nut — GB/T 6180 / ISO 7036 (Series 048), the alternative stainless grade is A2 (304). The practical dividing line is chlorides: A2 (304) is fine until salt is involved, and A4 (316) exists for the cases where it is — coastal, marine and road-salt service. Neither reaches the strength of a plated class 8.8 or 10.9 fastener.
Using Stainless Fasteners in Aluminum
Stainless steel is more noble than aluminum, so with an electrolyte present — rain, condensation, salt spray — the aluminum becomes the anode and corrodes at the joint. Area ratio decides how bad it gets: a small stainless fastener in a large aluminum section is normally acceptable, a large stainless fastener in thin aluminum is not. Where the joint gets wet, isolate the metals with a coated or nylon washer and a sealant, or specify an aluminum or coated fastener instead.
Sizes of Castellated Hex Nut — GB/T 6180 / ISO 7036 (Series 048) Available in A4 Stainless Steel
| Size | Pitch (mm) | Width across flats s (mm) | Width across corners e (mm) | Total height m (mm) | Slot width (mm) | Reference standard |
|---|---|---|---|---|---|---|
| M3 | 0.5 | 5.5 | 6.01 | 4.0 | 1.2 | ISO 7036 / GB/T 6180 |
| M4 | 0.7 | 7.0 | 7.66 | 5.0 | 1.5 | ISO 7036 / GB/T 6180 |
| M5 | 0.8 | 8.0 | 8.79 | 6.7 | 1.8 | ISO 7036 / GB/T 6180 |
| M6 | 1.0 | 10.0 | 11.05 | 7.7 | 2.0 | ISO 7036 / GB/T 6180 |
| M8 | 1.25 | 13.0 | 14.38 | 9.8 | 2.5 | ISO 7036 / GB/T 6180 |
| M10 | 1.5 | 16.0 | 17.77 | 12.4 | 2.8 | ISO 7036 / GB/T 6180 |
| M12 | 1.75 | 18.0 | 20.03 | 15.8 | 3.5 | ISO 7036 / GB/T 6180 |
| M14 | 2.0 | 21.0 | 23.36 | 17.8 | 4.0 | ISO 7036 / GB/T 6180 |
| M16 | 2.0 | 24.0 | 26.75 | 20.8 | 4.5 | ISO 7036 / GB/T 6180 |
| M18 | 2.5 | 27.0 | 30.14 | 22.5 | 4.5 | ISO 7036 / GB/T 6180 |
| M20 | 2.5 | 30.0 | 33.53 | 24.0 | 5.5 | ISO 7036 / GB/T 6180 |
| M24 | 3.0 | 36.0 | 39.98 | 29.5 | 6.0 | ISO 7036 / GB/T 6180 |
| M30 | 3.5 | 46.0 | 50.85 | 36.0 | 7.0 | ISO 7036 / GB/T 6180 |
| M36 | 4.0 | 55.0 | 60.79 | 43.0 | 8.0 | ISO 7036 / GB/T 6180 |
Dimensions are independent of the material: every size above is available in A4 Stainless Steel.
Custom manufacturing · Made to drawing
Need this nut in a grade that is not listed?
A4 Stainless Steel is one of the grades the catalog describes. Thread, height, across-flats, property class, locking feature and flange form can all be varied, including thread sizes the standard series does not run to. Made by cold heading or tapping.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
