A4 Stainless Steel Plain Washer are supplied to GB/T 858. The grade provides superior, including marine and chloride environments and is largely non-magnetic; the practical service range is approx. -200 °C to +400 °C, subject to the property class and the joint. Property data, grade comparison and the full size table follow.
Why Choose A4 Stainless Steel for Plain Washer — GB/T 858 (Series 071)
Specified for marine, coastal and chemical applications. For plain washer — gb/t 858 (series 071), this matters when superior, including marine and chloride environments is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 3506 group A4 (316 / 1.4401), commonly supplied A4-80 |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C, subject to the property class and the joint |
| Corrosion characteristic | Superior, including marine and chloride environments |
Corrosion Behavior in Service
A4 (316) adds 2–3% molybdenum to the A2 (304) composition, which dramatically improves resistance to chloride-pitting corrosion. For Plain Washer — GB/T 858 (Series 071) in marine, coastal, swimming-pool or food-processing environments, A4 is the default selection.
Galvanic & Galling Considerations
For stainless plain washer — gb/t 858 (series 071) the compatibility question is galvanic rather than galling: joined to aluminum or galvanized steel in wet service, stainless drives corrosion of the less-noble metal. Isolate with a coating, sleeve or non-conductive washer where the joint sees moisture. Note also that stainless is softer than hardened carbon steel, so where the part carries a wear or shear duty, check the load against the grade before substituting.
Using Stainless Fasteners in Aluminum
Expect the aluminum to corrode, not the fastener — stainless sits higher in the galvanic series, so the aluminum is the one that gives up material. A small fastener in a thick section spreads the loss over a large area and is usually fine; a large fastener in thin sheet concentrates it and is not. Keep water out of the joint, or isolate the two metals with a nylon or coated washer and a sealant.
Sizes of Plain Washer — GB/T 858 (Series 071) Available in A4 Stainless Steel
| For bolt size | Inner diameter d1 (mm) | Outer diameter d2 (mm) | Thickness t (mm) | Reference standard |
|---|---|---|---|---|
| M3 | 3.2 | 7.0 | 0.5 | ISO 7089 / GB/T 97.1 |
| M4 | 4.3 | 9.0 | 0.8 | ISO 7089 / GB/T 97.1 |
| M5 | 5.3 | 10.0 | 1.0 | ISO 7089 / GB/T 97.1 |
| M6 | 6.4 | 12.0 | 1.6 | ISO 7089 / GB/T 97.1 |
| M8 | 8.4 | 16.0 | 1.6 | ISO 7089 / GB/T 97.1 |
| M10 | 10.5 | 20.0 | 2.0 | ISO 7089 / GB/T 97.1 |
| M12 | 13.0 | 24.0 | 2.5 | ISO 7089 / GB/T 97.1 |
| M14 | 15.0 | 28.0 | 2.5 | ISO 7089 / GB/T 97.1 |
| M16 | 17.0 | 30.0 | 3.0 | ISO 7089 / GB/T 97.1 |
| M18 | 19.0 | 34.0 | 3.0 | ISO 7089 / GB/T 97.1 |
| M20 | 21.0 | 37.0 | 3.0 | ISO 7089 / GB/T 97.1 |
| M24 | 25.0 | 44.0 | 4.0 | ISO 7089 / GB/T 97.1 |
| M30 | 31.0 | 56.0 | 4.0 | ISO 7089 / GB/T 97.1 |
| M36 | 37.0 | 66.0 | 5.0 | ISO 7089 / GB/T 97.1 |
Dimensions are independent of the material: every size above is available in A4 Stainless Steel.
Custom manufacturing · Made to drawing
Need this washer in a grade that is not listed?
A4 Stainless Steel is one of the grades the catalog describes. Bore, outside diameter, thickness, temper and finish are the variables here — there is no thread to specify, so the fit and the bearing area are what the drawing has to pin down. Made by stamping or punching.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
