A4 Stainless Steel Round Head Solid Rivet combine the dimensional form of GB/T 867 / DIN 660 with the material properties of grade ISO 3506 group A4 (316 / 1.4401), commonly supplied A4-80: superior, including marine and chloride environments, largely non-magnetic, service range approx. -200 °C to +400 °C, subject to the property class and the joint. This page summarizes the grade data, its corrosion behavior in service, the comparable grades, and the sizes supplied.
Why Choose A4 Stainless Steel for Round Head Solid Rivet — GB/T 867 / DIN 660 (Series 097)
Specified for marine, coastal and chemical applications. For round head solid rivet — gb/t 867 / din 660 (series 097), this matters when superior, including marine and chloride environments is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 3506 group A4 (316 / 1.4401), commonly supplied A4-80 |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C, subject to the property class and the joint |
| Corrosion characteristic | Superior, including marine and chloride environments |
Galvanic & Galling Considerations
For stainless round head solid rivet — gb/t 867 / din 660 (series 097) the compatibility question is galvanic rather than galling: joined to aluminum or galvanized steel in wet service, stainless drives corrosion of the less-noble metal. Isolate with a coating, sleeve or non-conductive washer where the joint sees moisture. Note also that stainless is softer than hardened carbon steel, so where the part carries a wear or shear duty, check the load against the grade before substituting.
Comparable Grades
For Round Head Solid Rivet — GB/T 867 / DIN 660 (Series 097), the alternative stainless grade is A2 (304). A2 (304) suits general indoor and outdoor service; A4 (316) adds molybdenum for marine and chloride environments. Where higher strength matters more than corrosion, switch to plated alloy-steel class 8.8 or 10.9.
Using Stainless Fasteners in Aluminum
Stainless steel is more noble than aluminum, so in the presence of an electrolyte — rain, condensation, salt spray — the aluminum becomes the anode and corrodes at the joint. The effect is driven by the area ratio: a small stainless fastener in a large aluminum section is normally acceptable, while a large stainless fastener in thin aluminum is not. Where the joint is wet, isolate the two metals with a coated or nylon washer and a sealant, or specify an aluminum or coated fastener instead.
Sizes of Round Head Solid Rivet — GB/T 867 / DIN 660 (Series 097) Available in A4 Stainless Steel
| Nominal diameter (mm) | Length L (mm) | Head diameter dk (mm) | Head height k (mm) | Material | Reference standard |
|---|---|---|---|---|---|
| 2.5 | 8 | 5 | 1.6 | Aluminum | GB/T 867 / DIN 660 |
| 3 | 10 | 6 | 1.9 | Aluminum | GB/T 867 / DIN 660 |
| 4 | 16 | 8 | 2.5 | Carbon steel | GB/T 867 / DIN 660 |
| 5 | 20 | 10 | 3.1 | Carbon steel | GB/T 867 / DIN 660 |
| 6 | 25 | 12 | 3.8 | Carbon steel | GB/T 867 / DIN 660 |
| 8 | 32 | 16 | 5.0 | Carbon steel | GB/T 867 / DIN 660 |
| 10 | 40 | 20 | 6.3 | Carbon steel | GB/T 867 / DIN 660 |
| 12 | 50 | 24 | 7.5 | Carbon steel | GB/T 867 / DIN 660 |
