Material page for stud / threaded rod in A4 Stainless Steel (ISO 3506 group A4 (316 / 1.4401), commonly supplied A4-80). The sizes below are the ones we supply; there is no published dimensional standard for this article, so the table rather than a standard number is what to quote. Corrosion behaviour is superior, including marine and chloride environments and the service range is approx. -200 °C to +400 °C, subject to the property class and the joint.
Why Choose A4 Stainless Steel for Stud / Threaded Rod — ISO / DIN (Series 154)
Specified for marine, coastal and chemical applications. For stud / threaded rod — iso / din (series 154), this matters when superior, including marine and chloride environments is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 3506 group A4 (316 / 1.4401), commonly supplied A4-80 |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C, subject to the property class and the joint |
| Corrosion characteristic | Superior, including marine and chloride environments |
Corrosion Behavior in Service
A4 (316) adds 2–3% molybdenum to the A2 (304) composition, which dramatically improves resistance to chloride-pitting corrosion. For Stud / Threaded Rod — ISO / DIN (Series 154) in marine, coastal, swimming-pool or food-processing environments, A4 is the default selection.
Comparable Grades
For Stud / Threaded Rod — ISO / DIN (Series 154), the alternative stainless grade is A2 (304). A2 (304) covers general indoor and outdoor service. A4 (316) adds molybdenum, which is what buys the chloride resistance for marine and de-icing-salt exposure. Where strength matters more than corrosion, plated alloy steel in class 8.8 or 10.9 is the swap to make.
Using Stainless Fasteners in Aluminum
Expect the aluminum to corrode, not the fastener — stainless sits higher in the galvanic series, so the aluminum is the one that gives up material. A small fastener in a thick section spreads the loss over a large area and is usually fine; a large fastener in thin sheet concentrates it and is not. Keep water out of the joint, or isolate the two metals with a nylon or coated washer and a sealant.
Sizes of Stud / Threaded Rod — ISO / DIN (Series 154) Available in A4 Stainless Steel
| Thread size | Pitch (mm) | Length L (mm) | Engagement depth bm (mm) | Material | Reference standard |
|---|---|---|---|---|---|
| M6 | 1.0 | 50 | 8 | Cl. 8.8 alloy steel | DIN 939 / GB/T 901 |
| M8 | 1.25 | 60 | 10 | Cl. 8.8 alloy steel | DIN 939 / GB/T 901 |
| M10 | 1.5 | 80 | 15 | Cl. 8.8 alloy steel | DIN 939 / GB/T 901 |
| M12 | 1.75 | 100 | 18 | Cl. 8.8 alloy steel | DIN 939 / GB/T 901 |
| M14 | 2.0 | 120 | 21 | Cl. 8.8 alloy steel | DIN 939 / GB/T 901 |
| M16 | 2.0 | 150 | 24 | Cl. 8.8 alloy steel | DIN 939 / GB/T 901 |
| M20 | 2.5 | 180 | 30 | Cl. 8.8 alloy steel | DIN 939 / GB/T 901 |
| M24 | 3.0 | 200 | 36 | Cl. 8.8 alloy steel | DIN 939 / GB/T 901 |
| M30 | 3.5 | 240 | 45 | Cl. 8.8 alloy steel | DIN 939 / GB/T 901 |
| M36 | 4.0 | 280 | 54 | Cl. 8.8 alloy steel | DIN 939 / GB/T 901 |
Dimensions are independent of the material: every size above is available in A4 Stainless Steel.
Custom manufacturing · Made to drawing
Need this bolt in a grade that is not listed?
A4 Stainless Steel is one of the grades the catalog describes. Dimensions, material, finish and form are specified from the drawing — a bolt outside the standard range is a variation on existing tooling rather than a new design. Made by cold heading or hot forging.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
