A4 Stainless Steel Concealed-Head Self-Clinching Studs and Standoffs are supplied to our own published dimensions — this is a trade-series article rather than one covered by a dimensional standard, so confirm the figures against the part you are replacing. The grade provides superior, including marine and chloride environments and is largely non-magnetic; the practical service range is approx. -200 °C to +400 °C, subject to the property class and the joint.
Why Choose A4 Stainless Steel for Concealed-Head Self-Clinching Studs and Standoffs
Specified for marine, coastal and chemical applications. For concealed-head self-clinching studs and standoffs, this matters when superior, including marine and chloride environments is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 3506 group A4 (316 / 1.4401), commonly supplied A4-80 |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C, subject to the property class and the joint |
| Corrosion characteristic | Superior, including marine and chloride environments |
Galvanic & Galling Considerations
Two important notes for stainless concealed-head self-clinching studs and standoffs: (1) stainless can gall on stainless threads under load — use a thread lubricant or anti-galling compound, especially for M6 and below; (2) when joined to aluminum or galvanized steel, stainless can drive galvanic corrosion of the less-noble metal in wet service — isolate with a coating or sleeve where appropriate.
Comparable Grades
For Concealed-Head Self-Clinching Studs and Standoffs, the alternative stainless grade is A2 (304). Choose A2 (304) for general use and A4 (316) wherever chlorides are present; the molybdenum in A4 is the whole difference. Remember that stainless is the corrosion answer, not the strength answer — for load, look at class 8.8 or 10.9 instead.
Using Stainless Fasteners in Aluminum
Stainless steel is more noble than aluminum, so with an electrolyte present — rain, condensation, salt spray — the aluminum becomes the anode and corrodes at the joint. Area ratio decides how bad it gets: a small stainless fastener in a large aluminum section is normally acceptable, a large stainless fastener in thin aluminum is not. Where the joint gets wet, isolate the metals with a coated or nylon washer and a sealant, or specify an aluminum or coated fastener instead.
Sizes of Concealed-Head Self-Clinching Studs and Standoffs Available in A4 Stainless Steel
| Thread size | Form | Maximum tightening torque (Nu00b7m) | Test sheet options | Installation |
|---|---|---|---|---|
| M3 | concealed-head standoff or stud | 0.55 | cold-rolled steel / 5052-H34 aluminum | self-clinching in sheet metal |
| M4 | concealed-head standoff or stud | 2.0 | cold-rolled steel / 5052-H34 aluminum | self-clinching in sheet metal |
| M5 | concealed-head standoff or stud | 3.6 | cold-rolled steel / 5052-H34 aluminum | self-clinching in sheet metal |
| M6 | concealed-head standoff or stud | 7.2 | cold-rolled steel / 5052-H34 aluminum | self-clinching in sheet metal |
Dimensions are independent of the material: every size above is available in A4 Stainless Steel.
Custom manufacturing · Made to drawing
Need this nut in a grade that is not listed?
A4 Stainless Steel is one of the grades the catalog describes. Thread, height, across-flats, property class, locking feature and flange form can all be varied, including thread sizes the standard series does not run to. Made by cold heading or tapping.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.







