A4 Stainless Steel (ISO 3506 group A4 (316 / 1.4401), commonly supplied A4-80) is specified for marine, coastal and chemical applications. Specified on hollow wall anchors (molly bolts) it determines the corrosion behaviour (superior, including marine and chloride environments) and the service temperature range (approx. -200 °C to +400 °C, subject to the property class and the joint); the dimensions are ours rather than a standard's, and are listed in full below.
Why Choose A4 Stainless Steel for Hollow Wall Anchors (Molly Bolts)
Specified for marine, coastal and chemical applications. For hollow wall anchors (molly bolts), this matters when superior, including marine and chloride environments is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 3506 group A4 (316 / 1.4401), commonly supplied A4-80 |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C, subject to the property class and the joint |
| Corrosion characteristic | Superior, including marine and chloride environments |
Corrosion Behavior in Service
A4 (316) adds 2–3% molybdenum to the A2 (304) composition, which dramatically improves resistance to chloride-pitting corrosion. For Hollow Wall Anchors (Molly Bolts) in marine, coastal, swimming-pool or food-processing environments, A4 is the default selection.
Galvanic & Galling Considerations
Two important notes for stainless hollow wall anchors (molly bolts): (1) stainless can gall on stainless threads under load — use a thread lubricant or anti-galling compound, especially for M6 and below; (2) when joined to aluminum or galvanized steel, stainless can drive galvanic corrosion of the less-noble metal in wet service — isolate with a coating or sleeve where appropriate.
Using Stainless Fasteners in Aluminum
The galvanic couple here runs the wrong way: aluminum is the less noble metal, so it corrodes and the fastener does not. What governs the rate is the ratio of areas — a large anode and a small cathode is a tolerable combination, the reverse concentrates the attack into thin material around the hole. An isolating washer plus sealant breaks the circuit; where that is impractical, match the fastener to the substrate.
Sizes of Hollow Wall Anchors (Molly Bolts) Available in A4 Stainless Steel
| Screw size | Drill hole diameter (mm) | Wall thickness range (mm) | Anchor length (mm) | Flange diameter (mm) | Setting | Material | Screw retained |
|---|---|---|---|---|---|---|---|
| M4 | 8 | 3~13 | 32 | 11.0 | Screw-set / setting tool | Zinc plated steel | Yes u2014 removable |
| M5 | 10 | 5~20 | 38 | 13.0 | Screw-set / setting tool | Zinc plated steel | Yes u2014 removable |
| M5 | 10 | 13~30 | 52 | 13.0 | Screw-set / setting tool | Zinc plated steel | Yes u2014 removable |
| M6 | 12 | 5~25 | 45 | 16.0 | Screw-set / setting tool | Zinc plated steel | Yes u2014 removable |
Dimensions are independent of the material: every size above is available in A4 Stainless Steel.
Custom manufacturing · Made to drawing
Need this anchor & concrete fixing in a grade that is not listed?
A4 Stainless Steel is one of the grades the catalog describes. Length and corrosion protection are the usual specials. The load a fixing will take is decided by the concrete and the edge distance, not by ordering a longer anchor. Made by hot forging or thread rolling.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
