A4 Stainless Steel (ISO 3506 group A4 (316 / 1.4401), commonly supplied A4-80) is specified for marine, coastal and chemical applications. Specified on indexing plungers it determines the corrosion behaviour (superior, including marine and chloride environments) and the service temperature range (approx. -200 °C to +400 °C, subject to the property class and the joint); the dimensions are ours rather than a standard's, and are listed in full below.
Why Choose A4 Stainless Steel for Indexing Plungers
Specified for marine, coastal and chemical applications. For indexing plungers, this matters when superior, including marine and chloride environments is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 3506 group A4 (316 / 1.4401), commonly supplied A4-80 |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C, subject to the property class and the joint |
| Corrosion characteristic | Superior, including marine and chloride environments |
Corrosion Behavior in Service
A4 (316) adds 2–3% molybdenum to the A2 (304) composition, which dramatically improves resistance to chloride-pitting corrosion. For Indexing Plungers in marine, coastal, swimming-pool or food-processing environments, A4 is the default selection.
Galvanic & Galling Considerations
Two important notes for stainless indexing plungers: (1) stainless can gall on stainless threads under load — use a thread lubricant or anti-galling compound, especially for M6 and below; (2) when joined to aluminum or galvanized steel, stainless can drive galvanic corrosion of the less-noble metal in wet service — isolate with a coating or sleeve where appropriate.
Using Stainless Fasteners in Aluminum
Stainless steel is more noble than aluminum, so with an electrolyte present — rain, condensation, salt spray — the aluminum becomes the anode and corrodes at the joint. Area ratio decides how bad it gets: a small stainless fastener in a large aluminum section is normally acceptable, a large stainless fastener in thin aluminum is not. Where the joint gets wet, isolate the metals with a coated or nylon washer and a sealant, or specify an aluminum or coated fastener instead.
Sizes of Indexing Plungers Available in A4 Stainless Steel
| Thread size | Pin diameter (mm) | Pin stroke options (mm) | Types | Housing | Pin | Knob |
|---|---|---|---|---|---|---|
| M8×1 | 4 | 4 / 6 | B / BK / C / CK / G / GK | blackened steel | hardened steel | polyamide |
| M10×1 | 5 | 5 / 8 | B / BK / C / CK / G / GK | blackened steel | hardened steel | polyamide |
| M12×1.5 | 6 | 6 / 9 | B / BK / C / CK / G / GK | blackened steel | hardened steel | polyamide |
| M16×1.5 | 8 | 8 / 12 | B / BK / C / CK / G / GK | blackened steel | hardened steel | polyamide |
| M20×1.5 | 12 | 12 / 15 | B / BK / C / CK / G / GK | blackened steel | hardened steel | polyamide |
| M24×2 | 16 | 16 / 20 | B / BK / C / CK / G / GK | blackened steel | hardened steel | polyamide |
Dimensions are independent of the material: every size above is available in A4 Stainless Steel.
Custom manufacturing · Made to drawing
Need this pin in a grade that is not listed?
A4 Stainless Steel is one of the grades the catalog describes. Tolerance class is what a special pin usually turns on — a locating pin and a retaining pin want very different fits in the same nominal size. Made by cold heading or turning.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.







